Search Documents

By Saied S. Navid, Michael A. Piepenburg, Richard F. Escandon, Robert C. Lindsay

INTRODUCTION Phase I of the Los Angeles Metro Rail Project, known as MOS-1 (Minimum Operable Segment-1), is the first phase of the 27 km± (17 mi) subway starter line. MOS-1 is currently under construction and involves approximately 6.4 km (4.4 mi) of subway, five stations, yards and shops routed through the downtown area of Los Angeles. The project will form the initial heavy rail backbone of a more extensive light and heavy rail transit system planned for the greater Los Angeles area in the future. Construction Contract A-171 is one of 4 tunnel contracts within MOS-1 and involves construction of twin tunnels running from the downtown metropolitan area west to MacArthur Park. The heavily populated and developed downtown area, potentially gassy ground conditions, and the possibility of undocumented abandoned oil wells in seismically active southern California made the design and construction of Contract A-171 a uniquely interesting project. This paper summarizes the construction history to date (December, 1988) including design geotechnical considerations, tunnel support design, as-built geologic conditions, shield tunneling performance through soft ground, and ground response. The findings presented herein may aid in the design and construction

Jan 1, 1989

By Jerry E. Olson

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied additional areas, encompassing 11,303 acres, on the east and west sides of the 20,727-acre Badlands study area (Olson, 1987) in order to evaluate their identified mineral resources. The Badlands study area additions are located in Crook and Deschutes Counties, OR, about 10 and 18 miles east of Bend, OR. No mineral resources were identified. The additional areas studied are underlain by Tertiary-and Quaternary-age basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, mining claims or mineralized areas occur within or near the Badlands study area additions. Slab lava of marketable grade and quantity was not found in either area. None of the study area is of current interest for geothermal resources, but the eastern study area addition has been leased (1984) for oil and gas.

Jan 1, 1989

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By Carolyn S. Watkins, Thomas E. Ward, Debby F. Bruhn, Vern Winston, Mary Lou Rowland, Deborah K. Bulmer

The genetic characteristics of members of the genus Acidiphilium are poorly understood. As part of our study of the genetics of these bacteria, a search was made for an endogenous bacteriophage. Such a bacteriophage has been discovered. Several properties of the phage have been investigated. The phage has a lambdoid morphology and is somewhat larger than lambda. A variety of factors which affect phage stability have been investigated. The bacteriophage infects several of the strains that have been tested. Study of this bacteriophage should greatly increase our understanding of genetic mechanisms in Acidiphilium.

Jan 1, 1989

By David C. McLean, Peter Penner, Martin de G. Salter

The Rogers Pass Project for C.P. Rail includes a 14.7 km tunnel and an 8.5m diameter concrete lined ventilation shaft to a depth of about 335m. The shaft collar is in bouldered water bearing glacial till to a depth of about 95m. Initial excavation in the overburden was with the aid of dewatering wells. When ground support problems arose the excavation was completed by a two stage freeze programme. Freeze holes were drilled from the shaft bottom. This most unusual method was successful in overcoming the difficulties safely and efficiently. The remainder of the shaft was sunk and lined conventionally. Finally, a central dividing wall was poured by jump forming from the bottom up. The wall was completed to a high standard at up to about 20 vertical metres per day.

Jan 1, 1989

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By B. L. Dorey

"Performance management is a systematic, practical approach to managing people. It is founded on some basic assumptions about people and is designed to focus on people in the work place. Organizing meaningful information and using it to involve people is a cornerstone of this system.Some common sense practices are developed to involve people in an organization's effort to improve performance. The successful implementation of this program requires solid commitment and total involvement from all levels of supervision and employees for maximum results and lasting impact. All levels of supervision participate in training sessions to tailor the systems for implementation in their areas. This style of management is data-oriented and the bottom line of success is to measurably improve performance. Basic Assumptions about PeopleMost people in an organization, regardless of level, take pride in their work and generally want to do a good job. When performance falls off, there is usually some explanation other than the employee not really caring. People like to know their exact responsibilities and clearly what is expected of them. People like to know where they stand with the boss and would like to be evaluated on what they do and accomplish, rather than on what others think or feel about them. Further, people like to be rewarded for their good results, indeed, to understand what motivates people, we must look at what happens as a result of their actions. Another belief is that supervisors often have a greater influence on the performance of their people than they fully realize. Simply letting people know how important their performance is can have an impact. The Key ElementsGiven these basic assumptions and beliefs about people, some common sense practices have been systematically developed to manage more effectively."

Jan 1, 1989

The mining and resources industry in general has relied on macro separation technologies (greater than 1 micron) through processes which include: ò sedimentation ò flocculation and coagulation screening and filtration ò absorption ò magnetic separation ò chemical leaching and precipitation Essentially, these processes and technologies provide the industry with an effective arsenal to handle most separation requirements to date. Dewatering of solutions is one of the most significant requirements of the resources industry, as practically all mining endeavours use water in their process for leaching, extraction, cooling, dilution or for potable drinking water.

Jan 1, 1989

By V. Srajer

Operations research includes the application of systems analysis to mining operations, the acquisition of field data and the creation and verification of computer models of these operations. These activities result in the generation of computerized mine planning tools which have a firm base-in observational facts. The Surface Mining Laboratory of the Canada Centre for Mineral and Energy Technology (CANMET), in Devon, Alberta has been engaged in operations research activities since 1982. The work includes computer simulation of truck/shovel, continuous mining equipment and dragline operations. Other examples include cooperative programs with industry (such as the demonstration and evaluation of an integrated truck management system), the development of a device to measure off-highway truck rolling resistance, and an automated remote data transmission network. The presentation outlines existing and proposed research projects of the Operations Research group.

Jan 1, 1989

The Gympie Goldfield was the sixth largest producer of gold in historic terms in Australia. The Joint Venture Agreement between BHP Gold Mines Limited and Devex Limited was signed in January 1987. Since that time, some $20 million have been spent on underground and surface exploration work in the southern portion of the goldfield. The project is of considerable interest as the dewatering, rehabilitation and equipping of an old rectangular timber-lined shaft has been undertaken. The project is located in Gympie, a city of 10,000 people. The issues of dealing with urbanisation and associated environmental aspects are vital to the success of the project. An outline of the project and the geology of the mineralised structures follows:

Jan 1, 1989

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

The AusIMM/AMIC code for reporting Reserves seeks to improve the calibre of professional reporting on this subject. But have they gone far enough? Should the code appreciate that the degree of reliability of estimates required will vary with the type of mining planned? How does one "confirm continuity" as required by the code? The aim of optimum development drilling is to achieve appropriate ore zone definition for acceptable estimates of reserves and their economic extraction. Can this procedure be in conflict with the code? How does it affect finance decisions?

Jan 1, 1989

By D. R. Spears, C. E. Jordan

The U.S. Bureau of Mines examined the influence of turbulence on the fine bubble flotation of fine-sized (minus 40 micron) galena in order to improve flotation efficiency. Fine bubble flotation was carried out in a spinning-disk flotation cell and was compared to results obtained from flotation in a conventional cell at equivalent agitation levels. An automated electrochemical technique was used to monitor the turbulent velocity distributions of the fluid within the cell as a function of time and position. The velocity profiles were used to increase the precision of the fine particle, turbulent flotation model. While improved flotation response was obtained with intense agitation, the effect of bubble size was small. These results matched the model's predicted response for fine particle flotation.

Jan 1, 1989

By M. T. Holroyd

Digital computer applications to minerals exploration remained largely an experimental alternative to manual techniques until well into the 1960's. Due to the high cost of computer time, and the lack of digital data and appropriate software, the most favoured applications in the early days were computationally intense tasks - those which produced the most results with the least demands for programing and data input, e.g. forward modeling. When large digitisers and plotters became affordable, the computer took over simple labour intensive tasks such as data transcription, and when software caught up, more complex tasks such as contouring. Digital data acquisition systems and superminicomputers made total computerisation of geophysical compilation and cartography possible and affordable. Applications continued to develop into areas of much greater logical complexity. Software, the new labour intensive process, still lagged behind. The microcomputer made computer applications potentially available everywhere to everyone. Desk-top micros as powerful as the minis of ten years ago can take on any geophysical exploration task currently done by computer - when the software becomes available.

Jan 1, 1989

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

Accidents in open pit mining have a high cost in lost time of person- nel, damage to equipment and installations, and lost production. The realities of export competition require that Mine Management sig- nificantly reduce the costs associated with accidents and workplace ill-health. Newer management approaches are proving effective in reducing the Total Cost of Risk through a strucured Occupational Health and Safety Programme exhibiting the following features: ò Formal Company Policy ò Accountability for OH&S performance clearly designated to each level of management and supervision ò Effective utilisation of a Mine Occupational Health and Safety Co- Ordinator and a Mine Occupational Health and Safety Adviser ò Development of realistic OH&S Objectives ò Training of Management, Supervision and Workforce in Occupa- tional Health and Safety ò Development and adoption of Safe Work Practices and Procedures ò Effective employee selection procedures, control of Contractors ò Monitoring of the health of the workforce ò Collection, recording and distributing information on all Mine inci- dents, accidents, injuries and damage ò Ensuring that the Mine environment is healthy and safe ò Effective Emergency Procedures to deal with injury, fire, rescue and other situations of risk ò Controlling those Mine hazards which cannot be removed ò Adopting a high standard of Occupational Rehabilitation ò On-going visible Management participation in the programme to ensure that momentum is developed and maintained. This approach requires that Occupational Health and Safety be given equal status with product quality, maintenance of plant and output per- formance; its implementation is rewarded with improved morale and major cost reductions.

Jan 1, 1989

By Jasinder S. Jaspal

Most of the underground coal in the United States is mined via room-and-pillar mining methods with continuous miners. These machines operate intermittently because they have to wait for shuttle cars to interchange positions. To overcome this discontinuity in shuttle car haulage and to realize the full production potential of continuous miners, the U.S. Bureau of Mines developed a multiple-unit continuous haulage (MUCH) system through a research contract with Jeffrey Mining Machinery Div. (JMMD). The MUCH system consists of 12 rubber-tired vehicles and a bridge conveyor. The rubber-tired vehicles are connected by a unique mechanical linkage system to form a 250-ft train. The mechanical linkage permits the vehicles to track-retrack the preceding vehicle in both inby and outby directions. The cut coal cascades from one vehicle to another until it is discharged on the section conveyor belt. The MUCH system provides continuous haulage to the continuous miner. The MUCH system was initially surface tested by JMMD. Subsequent extensive testing was conducted by the Bureau at its test facilities at Bruceton, P A. Deficiencies found during testing were corrected. This report summarizes initial tests by JMMD and subsequent extensive tests and evaluation by the Bureau.

Jan 1, 1989

By R. Hogg

"Particles play an important role in our environment and in many aspects of human activity. Much of the Earth's surface - sand, soil, rocks - consists of particles, as do clouds in the atmosphere, smoke from fires, and dust in our homes. Many of the foods we eat - cereals, flour, instant coffee - and everyday items such as pharmaceuticals, cosmetics, detergents and other cleaning products are encountered in the form of particles. Inks and paints consist of very fine particles dispersed in liquids. Modem agriculture uses huge quantities of fertilizers and pesticides, largely in particulate form. The list could be extended almost indefinitely; particle systems are obviously an important part of our daily lives. But what do we know about them? For most people, the answer is probably: not much.We are all familiar with the three common states of matter: gas, liquid and solid. In many respects, particle systems should be regarded as a distinct class of their own. The particles themselves may be solid but we all know that a heap of sand is quite different from a solid rock. A cloud of liquid droplets - fog - has much more in common with a cloud of solid particles - smoke - than it does with a bucket of water. There are certain characteristics and properties which are unique to the particulate state. The behavior of any particle system is determined not only by the material from which the particles are made, but also by interactions among the particles and with their environment. These interactions become increasingly important as the size of the particles decreases, and for exceedingly fine particles, smaller than about one micrometer (0.000001 meters or 0.00004 inches), these interactions dominate and we enter the realm of colloidal systems.Particle SystemsA system in which discrete entities - particles -are dispersed in a continuous medium can be regarded as a particulate system. The particles and the medium can consist of a solid, liquid or gas. The various combinations and some common examples are listed in Table 1. The properties and behavior of these systems depend on the characteristics of the particles, the nature of the medium, and the relative abundance of the two phases. In general, it is the latter which determines the kind of behavior exhibited by the system.As a general rule, the behavior of particle systems follows that of the dispersed phase (the particles) at high concentration, and that of the continuous phase (the medium) at low concentration. For example, both powders and smokes consist of solid particles in a gaseous medium. However, in a powder the solids typically occupy over one half of the total volume; in many respects powders behave like solids. In a smoke, on the other hand, the particles may take up only a few parts per million of volume, so that these systems generally behave like gases."

Jan 1, 1989

By Janine L. Beazley, James H. Kyle

The effects of pH, pH modifier (lime or caustic soda) and cyanide on the pulp rheology of a number of ore types ranging from highly siliceous to highly kaolinitic has been investigated. All experiments were performed in fresh water at solids concentrations of 25 and 45% solids and in the pH range 6 to 11. The kaolinitic ores exhibited greater changes in rheology with pH and calcium ion concentration than did the siliceous ores.

Jan 1, 1989

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989