Search Documents

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By Sean Gallagher

This report describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries.

Jan 1, 1989

By William Petruk

An investigation was conducted to determine types of particles that tend to be recovered in concentrates by mineral beneficiation. It was found that, in concentrates of the same grade the proportion of desired mineral occurring as apparently liberated grains varies widely. In contrast the proportion is nearly constant when the grains considered are apparently liberated grains plus unliberated grains in particles composed largely of the desired mineral. It was also found that the types of particles which tend to be recovered in concentrates are dependent upon the concentrate grade. Hence it is much more important to determine the characteristics of recoverable particles and to measure the percentage of mineral that occurs in recoverable particles. than to measure the percentage of totally liberated mineral. A relationship between concentrate grade and type of particle that tends to be recovered in concentrates was established.

Jan 1, 1989

By R. Hogg, S. Chander

"INTRODUCTION The behavior of particulate systems in general is determined by the properties of the solid and fluid phases and of the interfaces between them. As particle size is reduced, the inter facial effects become increasingly important until, in colloidal systems, they become completely dominant. Interfacial phenomena are especially important in coal processing for a variety of reasons. Because coal is naturally hydrophobic and its density is low, surface forces begin to dominate over gravity at relatively coarse sizes. Coal is thermodynamically unstable in the presence of air, so that surface oxidation occurs readily leading to important variations in surface properties with time and environment. These effects are further compounded by the inherent heterogeneity of the material.Surface characteristics and properties play a significant role in most aspects of coal processing. Comminution, for example, is a process of creating new surface, while agglomeration involves the reduction of surface area and is usually controlled by surface forces. Both solid-solid and solid-liquid separations are influenced by interracial phenomena, Gravity separations are usually performed in a liquid phase and are affected by the wetting characteristics of the various solids present and by the need to ensure proper dispersion of the individual particles. Froth notation, of course, separates particles on the basis of differences in surface characteristics. Chemical processes such as leaching generally involve interfacial reactions whose rates depend on surface area and may be influenced by electrochemical effects in the electrical double layer at the solid-liquid interface, or by adsorption of reactant and/or product species from solution. Solid-liquid separations and associated processes such as flocculation are strongly dependent on the nature and properties of the solid-liquid interface.In characterizing solid surfaces, it is important to consider first the surface area, since this determines the relative importance of the interfacial effects. The structure and chemical composition of the surface may depend on the distribution of different petrographic constituents and impurities such as finely disseminated mineral matter, on the extent of surface oxidation, and on adsorption from the environment. These, in turn, will generally determine the surface properties which define particle behavior. Since the relationships between structure etc. , and properties are not generally known, it is usually necessary to measure properties such as wettability and electrical charge directly."

Jan 1, 1989

The mining industry has a well deserved reputation earned over the years for innovation, engineering, management and the quick application to mining of emerging technology. The cumulative result is the economic exploitation of lower grade resources. The developments during the last decade have done nothing to tarnish the reputation. There are many that come easily to mind: the use of contractors for both surface and underground operations, a trend toward mine management contracts, the increasing recognition of the economic potential of ground support, and the development of physical measures to achieve it, - sophisticated measures to analyse blasting , and thus improve fragmentation, - instrumentation to assist geotechnical appraisal, - the development and application of the powerful and flexible, excavator, - the evolution of measures to improve grade control, - massive improvements in equipment productivity and reliability built largely around the application of hydraulics, - the development of powerful computer packages for orebody modelling, mine design and extraction, - simple "dense" fill systems, - maintenance management techniques including the greater use of off-site maintenance of exchange components, - the utilisation of communication systems for data transfer.

Jan 1, 1989

By Meliton M. Garcia, Satya Harpalani

This paper discusses the results of an investigation carried out in an underground mine to characterize the volatile by-products adsorbed on airborne particulates following the detonation of four common explosives including ANFO. The primary objective of this study was to determine if any organic amine compounds, particularly nitrosamines, and any polycyclic aromatic hydrocarbons were produced and trapped in the dust that a miner might inhale during the workday. The production of these substances is of great concern because of their suspected carcinogenic nature. The results of the study indicated that a large variety of the by-products are adsorbed on the particulates generated, and thus remain airborne following the detonation of explosives. The major by-products retained by the dust were bis(2-ethylhexyl) phthalate, and aliphatic hydrocarbons with carbon chains ranging from C12 to C28. One explosive, a water gel, produced the polycyclic aromatic compound, trimethylnaphthalene. No nitrosamine compounds were detected.

Jan 1, 1989

By N. S. Dalal, X. N. Hu, X. Shi, V. Vallyathan

"Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the major industrial health hazards all over the world. Although silicosis has. been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed subjects; personal respiratory patterns; and presence of any coexisting disease (such as tuberculosis or rheumatoid arthritis) all influence the expression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989

By M. G. B. Wheeler

SYNOPSIS This report outlines the development of a model to simulate the radiometric sorting of gold- and uranium-bearing ores. The developed program indicates the optimum mass, reject percentage, and expected reject gold and uranium grades for a radiometric sorter. It achieves this by statistical analysis of the data gathered from a large sample of rocks in the required size range for a particular mine. The program can be used in the optimization of existing sorters, as a design tool for new radiometric sorters, and in feasibility studies on radiometric sorting.

Jan 1, 1989

By Frank W. Pereira

The Montana Talc ore body was discovered in 1983 in Montana's Gravelly Range, about 40 km (25 miles) south of Ennis. Initial drilling indicated a 910-kt (1-million st) ore body of high purity talc. Preliminary analyses on ore cuttings included chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. Results indicated it was similar to talc currently being marketed from Montana and it would probably have good commercial value. Based on the positive test results, a test pit was made and a 180-t (200-st) sample of ore was mined. A portion of the ore was ground to various particle sizes and evaluated to determine its strengths, weaknesses, and other characteristics. The deposit is located close to the Cyprus Yellowstone deposit. It was therefore believed that Montana Talc ore may possess many of the same characteristics. Testing and analyses showed the talc to have a high purity and an extremely large surface area, even for Montanatype tales. The ore was also situated in a massive deposit, indicating low cost mining. While the lab analyses were encouraging, the true evidence would be obtained from commercial tests in the marketplace. About 91 t (100 st) of ore were ground to product specifications for pitch control, paint filler, and plastics filler. Consumers were contacted and requested to evaluate the sample talc products. A major trial for the talc as a pitch control agent was arranged at a Northeast paper mill. The trial indicated the new Montana Talc product performed as well or better than the current standard in the industry. In fact, due to a minor modification in the compaction process to make the transport of the talc easier, the product had substantially less dust than the currently used product. The operating people at the paper mill requested that management purchase this talc. Trials were also run at paint plants for use as a pigment filler. And the talc was fabricated into a number of plastics compounds. The initial product tests were largely positive and provided encouragement to proceed with the project. Different grinding mills were used and their performance evaluated. Significant data were generated by the custom grinders. They indicated how the Montana Talc ore ground and the particle size distributions produced at different grinding settings. Encouraged by the positive marketing tests, a prefeasibility study was commissioned. A talc grinding plant and mine plans were designed and capital and operating costs estimated. Initial economics showed an attractive return. The operating costs were among the lowest in the industry. The positive economics, along with the excellent results by the products in the marketing tests to the paper, paint, and plastics industries, led to the recommendation to proceed with the project. Plant construction began in June of 1985. The Montana Talc Co. (MTC) analyzed the data from the commercial tests. Based on the product's outstanding performance and the uniqueness of its high purity and platy structure, a strategy was developed to position the company as a premium talc supplier.

Jan 1, 1989

By S. Henley

There is much in common between the requirements of open-pit mining and quarrying operations. Both involve the extraction of large volumes of material from surface excavations. The principal differences are of degree: open-pit mining of materials such as coal or gold generally involves the extraction of only small volumes of 'mineral' and large volumes of waste-they are operations with very high stripping ratios, and are made viable only because of the high unit value of the extracted mineral. In quarrying operations, the unit value of the mineral - sand, aggregate, limestone, or clay - is much lower, but stripping ration Are also lower. Thus the same techniques of geological modelling, reserve estimation, and pit planning are applicable, as is shown in two examples from the British quarrying industry. In each case, a primary requirement is the definition of production volume or tonnage. Sometimes, this need may be addressed simply by the use of a survey data processing package. However, in other cases, such as the two examples addressed in this paper, of sand and clay quarries, detailed assessment of the variation of mineral grades is a vital part of the exercise, and simple volumetric modelling cannot in itself be sufficient. In these cases, a block model approach using simple logical and numerical post-processing is also required to obtain required parameters for commercial classification of the products to be extracted. Pit designs themselves may be optimised by use of algorithms such as Lerchs-Grossmann, but the value of mineral produced can be dependent on factors other than its grade in any one part of a single pit, and the 'optimised' pit itself must be considered only a good sub-optimal. Given the right degree of healthy skepticism, and a software package with sufficient flexibility to be adapted readily to the rather different requirements of the quarrying industry, there is no reason why the quarrying industry should not benefit from the many years of investment in mining software technology.

Jan 1, 1989

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By C. Dupuis

Thiourea is a promising reagent for gold extraction especially from refractory ores that cannot be treated by traditional cyanidation route. In this study recovery of gold from thiourea leaching solutions was investigated by direct electrowinning. The electrolysis cell consisted of a carbon flow-through cathode and a lead anode. The anodic and cathodic compartments were separated by a membrane. Galvanostatic mode was chosen for operation of the cell. Factors affecting recovery efficiency such as cathode thickness, linear flowrate, current intensity, thiourea and gold concentrations were investigated. The influence of some species in solution on efficiency and selectivity of recovery was investigated. Gold recovery reached 99% but current efficiency was lower than 10%. The complex formed with ferric ion and formamidine disulfide are reduced before gold-thiourea complex. Thiourea consumption occurred during leaching mainly by oxidation and reaction with dissolved copper.

Jan 1, 1989

By J. M. Menacho, J. M. Reyes

"Batch and continuous regrind tests were conducted in 3 kW and 15 kW tower mill units, respectively. Single particle size classes of a chilean copper sulphide concentrate were employed in the batch tests, while a fraction of the plant stream was deviated to the continuous unit operated under different conditions.Results are interpreted in terms of the simplified grinding kinetic model energy-based and conveniently adapted to this application. Based on the above figures plus some industrial data supplied by MPSI Inc., a scale-up relationship was developed for the apparent specific rate of breakage siE, as a function of the net power draw P, i.e.siE = siE text (P/P test) 0.089This equation fit very well the available data at the three scales and its application to regrind 4400 t/day of rougher copper concentrate from 70% below 325 Tyler mesh to 95% below same mesh, involves around 30% energy-saving compared to standard ball mill for same grinding task.INTRODUCTIONImpact and abrasion-attrition breakage are two extreme mechanisms present in any grinding system in a proportion defined by specific design and operating conditions. Impact breakage is generally efficient for coarse grinding, while abrasion-attrition is adequate to produce fine particles. Efficiency of conventional tumbling mills decreases as fineness of the product increases, even though distribution of applied stresses is always much stronger than internal force distribution in the particles. On the other hand.in a vertically stirred ball mill like the tower mill, distribution of applied stresses and particle strengths are in the same order of magnitude, making possible nearly ideal abrasion conditions (1).Tower mill configuration includes a cylindrical body vertically mounted and provided with a central screw with flights to produce circulation of balls moved up through the inner region to return down by the external space. Fresh material can be fed into the top , center or bottom in order to assure appropriate agitation of suspended particles. Size reduction and evacuation rates should compensate settling of coarse particles to avoid sanding of the screw. Detailed description of the tower mill and its operation have been given elsewhere (2),(3)."

Jan 1, 1989

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

Relatively lower recoveries (60%) of coarse phosphate (-16 +35 mesh) particles are attributed to the difficulty in transportation of coarse particles from the pulp to the froth column and rapid drainage of these particles from the froth column to the pulp. Increasing the hydrophobicity of coarse particles by higher, more efficient coating of the collector and using larger froth volumes have been suggested to overcome these problems. In this study, the role of emulsification of the fatty acid-fuel oil collector on the flotation recovery of coarse particles was examined. It was determined that emulsification can not only increase the coarse particle recovery, but do so at higher fractions of fuel oil in the collector, thereby reducing the reagent cost as well.

Jan 1, 1989

By David E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surface underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material. Extended seismic arrays were used to identify the vibration characteristics within a few tens of feet of the blasts and also as modified by the propagating media at distances over 1 mile. Production blasts and specially fired single-charge blasts allowed the determination of natural ground frequency and the influence of initiation delay timing. Vibration amplitudes from the production blasts at all sites exceeded historical norms, particularly at the greater distances. This contrasts with the near-normal results from single-charge blasts. Apparently, between-hole time delays were insufficient to separate vibrations from adjacent charges for the low-frequency waves present. Single-charge tests showed that the propagating media produced low-frequency, ground-roIl-type surface waves at nearly all sites. Large blasts at such sites could produce an unacceptable risk of vibration-induced cracks in nearby structures.

Jan 1, 1989

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By D. L. Johnson

A number of small but rich copper sulfide (chalcocite) ore deposits are located on Michigan's Keweenaw Peninsula. These deposits are considered too small to warrant the capital investment required for conventional mining. However, they are being considered for in-situ solution mining as a way to revitalize the area's once prosperous copper extraction industry. Geology, mineralogy and geohydrology of the deposits have been investigated to determine their suitability for leaching; Three conclusions were drawn from the work. First, the sulfide mineralization is found primarily in fractures (65%) and, therefore, is accessible to injected leach solutions. Second, the ores are shallow, occurring from surface exposure to about 200 meters depth; injection and recovery wells would not have to be excessively deep. Third, the rock was found to have low permeability, in the neighborhood of thirty millidarcys or less. However, preliminary hydraulic fracturing experiments indicate that this will be an effective method for permeability enhancement. In one experiment a permeability increase of 100 times was achieved using a very low injection pressure at shallow depth. Additionally, fracture aperture spacings measured from drill core were correlated with fair success to field permeabilities.

Jan 1, 1989