Search Documents

By Boontanjai C, Boyapati ER

Reagents used for batch flotation tests were Aeroxanthate-343 & 350, Dow Z-6, & reagent-4037 (from Benambra) as copper collectors; Na2SiO3 & Na2S2O3as gangue depressants; lime & HCl as pH regulators; and pine oil & MIBC (methyl isobutyl carbinol) as flotation frothers. A Denver Sub A flotation cell of capacity 250 gms was used for the batch flotation experiments. Atomic absorption spectrophotometer was used for copper assays and microscopy for selectivity and liberation studies. Melbourne tap water was used throughout the experiments. Unless otherwise stated, the following parameters apply to the flotation experiments: flotation impeller speed - 1300 rpm, pulp density during flotation- 22%, reagents addition - in 4 stages, total conditioning time for collectors - 8 minutes, total flotation time- 9 minutes. A variable quantity of copper mineral collector according to the test in question was added, then conditioned the pulp for 2 minutes. The froth was removed by hand, scraping the full length of the cell at constant depth every 10 seconds. No frother is required for this copper tailing flotation. Four concentrates were collected after addition of collector and conditioning at 2,4,6 and 9 minutes. The pulp volume was maintained at a constant level to yield a constant froth depth.

Jan 1, 1990

By W. Nahas, T. C. Watson, A. R. Maycock

The development of roasting technology for the oxidation of sulfides in refractory gold ores is discussed. Case studies covering operations dating from the mid-1930's to the present day are used to illustrate this development. The roasting of ores and concentrates is reviewed and various gas cleaning flowsheets are discussed with particular reference to environmental requirements. A sequence chart is provided to show the development path of a potential roasting project.

Jan 1, 1990

By R. Eggert

Since the discovery of high temperature superconductors has led to extensive interest and conjecture regarding their potential to change contemporary technology, discussions of the impact on the metallurgical and other industries have naturally arisen. In this paper we present data showing the possible impact of these developments on the materials related to the fabrication and proliferation of devices based on superconductor materials. We observe that the largest volume of effort with LTSC will be for the demonstration of high power devices while applied research relating to processing will remain the principal HTSC activity. We also note that in the next decade copper consumption in the US is expected to remain essentially at the current level while the need for Nb and Sn,; two major components of LTSC, will grow at a faster rate both in the US and the world. Although the use of superconductor-based magnetic separation is anticipated to increase, no major impact of these components on the metallurgical industries is expected.

Jan 1, 1990

By Egons R. Podnieks, Wallace W. Roepke

Mining technology to utilize vital lunar resources will be required for any commitment to permanent lunar basing. Lunar mining must be viewed both as a major supporting element for space resource commercialization and for creation of human settlements on lunar and planetary surfaces to support long-range space exploration. The Apollo missions to the lunar surface and results from fundamental research on analogue lunar rocks by the Bureau of Mines, and others, have provided the initial data for developing lunar mining technology. The multi-disciplinary research projected in this paper outlines the scientific and engineering needs to realize the lunar mining goals.

Jan 1, 1990

By W. E. Cooper

The International Intercalibration and Intercomparison Program (HIP), consisting of several selected laboratories from four countries, held a radon progeny intercomparison measurement at the U.S. Bureau of Mines experimental Twilight Mine on September 12-14, 1988. Grab samples were taken at four different conditions of low and high radon progeny and condensation nuclei concentrations, respectively. The results showed good agreement among all seven participants. The coefficient of variation of all measurements was 4.7%; after minor corrections for flows and some systematic biases, it was reduced to 3.2%.

Jan 1, 1990

By D. R. Hardman

Coal mining has been practised in South Africa for over one hundred years. The total production increased gradually in the early pat of the twentieth century, but over the past twenty years the rate of growth has been considerable. Although opencast mining has contributed largely to this increase in production in recent years, underground bordand- pillar operations still contribute slightly less than 50 per cent of the total production. The paper highlights problems arising from old bord-and-pillar workings, and an indication is given of how some of the problems have been addressed.

Jan 1, 1990

By Kuipers A. J

Aberfoyle has been applying computer methods to mine geology in small to medium-sized underground mines since the early 1980's. Recently, the installation of DATAMINE software at the Hellyer Mine in Tasmania has allowed development of computerised applications which assist both mine geologists and mine planning engineers on a daily basis.Comprehensive data is entered into a database prior to survey coordinating to produce a processed database which can be accessed for construction of a variety of plots. The folded and faulted nature of the orebody contacts at Hellyer has necessitated the use of the structure contour method to provide a complete 3-D spatial interpretation. Computer-generated contact intersection points are hand-contoured before digitising and wireframing as a digital terrain model. This wireframe model can be sectioned in any plane for mine planning.

Jan 1, 1990

By Alistair Frame

INTRODUCTION In April 1988 discussions were about to start with BP on the possibility of buying their- mineral interests, and it took a long time to arrange a deal. I will talk about RTZ without BP Minerals, look at the new RTZ with BP Minerals, discuss the outlook for metal prices, and review the problems in South Africa and develop the case against sanctions on that country. RTZAT THE END OF 1988 Late in 1987, after completing a worldwide review of our strategic thrust, we decided: 1. That the business focus would be to remain a major diversified natural resource group with interests in related industries. 2. To divest non-core and low growth businesses. 3. To develop a logical acquisition plan. 4. To emphasise organic growth and, most importantly, to enhance shareholders' wealth by capital increase and a progressive dividend policy. Subsequently, we concluded that we should sell our oil and gas business and dispose of several assets for which we saw little growth potential. The disposal programme raised some U.S.$ 1,600 million, representing a significant capital gain on our various investments. All transactions were carried out by our small Head Office staff in London, without the help of merchant banks and lawyers, and we were able to safeguard the employment of our staff in all these operations. The most interesting disposal was of our oil and gas interests. Before the 1987 strategic review, we had ambitions to develop our oil and gas interests and to become the leader in the second division of European oil companies. Our interests, which were purely in exploration and production of oil and gas, consisted of the 100% owned RTZ Oil and Gas company, and 29% of LASMO, a publicly quoted U.K. oil and gas company with extensive worldwide interests. LASMO, in turn, owned 25% of Enterprise Oil, one of the more successful of the North Sea oil exploration and production companies. Prior to the end of 1987, our intention was to acquire control of both LASMO and Enterprise. However, when we evaluated the net asset value of these two companies based on our oil price assumptions, which were pessimistic for the next five years or so, we concluded that they were both trading in the market at significant premiums. This, taken with the additional premium required for acquisition and the high cost of exploration, led us to conclude that, since funds could undoubtedly be used to better effect, we should sell our interests. Turning to the other major achievements in 1988, we commissioned, and built up to design levels in a very short period of time, the Morro do Ouro gold mine in Brazil. This mine reached its design output of 100,000 ounces of gold per year within three months of start-up, which was on time and under budget. We are now considering a possible expansion of this property. In South America, Utah International, Mitsubishi and RTZ arranged non-recourse finance, with post completion guarantees, for the giant Escondida Project in Northern Chile. Financing came from a group of banks in Japan, Germany and Finland -- the countries to which most of the concentrates will be sold -- and from the LEC. The average output of the mine for the

Jan 1, 1990

By H. Forrest

Lead smelting at Cookson Industrial Materials was formerly carried out using a combination of Blast and Reverberatory Furnaces. In the late 70' s these furnaces were replaced by two 20 tonne capacity Rotary Furnaces. This furnace type has proved to be more flexible in the range of feedstock that can be processed, including lead drosses, battery plate and even whole batteries. High rates of production have been achieved whilst attaining a good level of environmental control. The majority of the sulphur in the feedstock can be fixed by use of appropriate fluxes.

Jan 1, 1990

By S. B. Patton, T. Novak, R. L. Sanford

A comprehensive approach to the development and organization of an expert system designed to assist electricians in diagnosing electrical faults in mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach, which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures in the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchal structure are formulated by creating "what if' scenarios and performing a qualitative circuit analysis for each fault. Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide reference material and tutorials on the circuit are also described.

Jan 1, 1990

By J. B. Gwiazda

Maintenance of a constant load setting throughout longwall support units and selection of the proper initial bearing capacity depending on the type of roof strata are the basic factors that ensure good performance of roof support in a longwall. These requirements can only be met by hydraulic support. The greatest advantage of hydraulic support is achieved when uniform pressure is imposed on the roof throughout the length of the longwall. Such support, however, is provided only if each of the support units acts with the same force against the roof, i.e., has the same setting load. In such cases, the roof behaves like a uniform plate without bending and shearing stresses, thereby ensuring an undisturbed structure. Without a positive set value system, achieving an equal setting load for all units of the longwall support is impossible. Due to alterations of the feed line pressure of support units as well as some reasons related to man's psychology, operators extend the height at different setting loads. This produces nonuniform roof stress, and disturbs the structure. Consequently, the roof usually cracks. The author has developed a positive set value system, which is described in this Technical Note. Selection of the setting load Two pressure values in the feed lines are usually applied in longwall hydraulic systems. Lightweight support is fed by 25 MPa (250 bar) liquid, while heavy duty units receive a nominal pressure of 31.5 MPa (315 bar). Such pressure is required not only for the props but also to power the adjust¬ment jacks and the advancing ram. If the feed pressure is too low, there will be difficulty in shifting the unit despite the inversion system of the advancing rams. On the other hand, for many roof types, the feed pressure often appears to be too high when applied as the setting load pressure. An excessive setting load acts too strongly against the roof, crushing weak strata close to the roof. The author has recognized a case where an excessive setting load destroyed not only the nearby roof strata but also the strata above a 2-m (6.6-ft) sandstone layer. In addition, an excessive setting load relieves the side¬walls, increasing the resistance when using cutting machines. As a result, the yield of coarse coal is diminished, and increased fines dominate in the final product, lowering its economic value. As indicated, selection of the proper setting load, depend¬ing on the mining and geological conditions of the extracted seam, is extremely important. In some mines, measures applied to prevent disturbances include reduction of the feed line pressure by adjusting the feed pump valve. The disadvantage accompanying reduced feed line pressure is more difficult operation in advancing the ram. Due to the reduced feed line pressure, the force of the advancing ram is much lower than the designed value. Other designs suggest using a third feed line. However, installation of supplementary valves on the support units is required, a time-consuming and expensive procedure. The disadvantages of the powered supports are eliminated by a system designed by the author. So far, such a method of setting load control has not been used in any type of support. Setting load control unit The designed positive valve set for prop loading and the setting load control correspond to existing control systems for hydraulic powered support. The layout of the unit connected to the hydraulic prop control is presented in Fig. 1. The unit is marked LIDS. It incorporates three valves that may operate separately or connected. Valve A automatically opens and closes with liquid flow in the prop feed circuit. The valve is opened when the canopy touches the roof and closed when the support unit is withdrawn. Valve B serves as the setting load control. Valve C automatically opens and closes the flow in the line connecting the under-piston space of E to the prop F with the separator G. The valve block of each support prop is marked BZ. The UDS unit is connected by the hydraulic lines to the F prop control circuit. A valve is connected by H to pressure line J and by K to the G separator. In the UDS-3 version, line L is connected to M, linking the over-piston space of F prop with the G separator. Valve B is linked with valve A by a connector; it is also connected to the under-piston space E of prop F by line P. Valve C is fixed between lines K and P, connecting space E of prop F with the separator G. When setting the support, the liquid flows from line J through separator G, the BZ valve, and valve C to the space E of prop F. When reaching the roof with the canopy, valve A is opened and C closes. In this way it is impossible for the operator to cause the liquid pressure in space E of prop F to reach the level of line J. The prop pressure is set by valve B of the UDS unit. When withdrawing the support, valve C is automatically opened and A closed. Three UDS units have been fabricated and are designated

Jan 1, 1990

By N. A. McPherson, P. C. Stevens, A. J. Rigby

"There has been a consistent move in recent years to continuously cast small billets while utilizing ceramic stream protection between tundish and mould. The need to have ceramic stream protection has developed from a need to improve billet surface quality by submerged pouring. The need to protect the ladle to tundish stream in conjunction with tundish to mould protection is explained.The continuous casting of thin slabs is at the development state and will require a great deal of ceramic development to ensure the economic viability of the project. An insight is given to the main problems.IntroductionDuring the early development period o f the continuous casting of steel in the late 1940s and 1950s, much of the work was carried out on small cross section products. For example, the continuous casting of 50 mm square billets was carried out on a production scale in the United Kingdom at Barrow. Slab casting was initiated on a production basis on 100 mm thick stainless steel slabs at Atlas Steel, Weiland, Ontario. In the case of slab casting the thickness increased gradually until it was similar to Slabbing Mill feedstock , i.e. in the range 200 mm to 250 mm , although stainless steel continued to be lower at around 185 mm thick.For billets , a significant proportion of steel is now cast at around 100 mm square which creates specific difficulties when casting with a submerged pour - mould powder practice. The move back to smaller cross sections is further emphasized by the current interest in "" Near Net Shape Casting"" . If this move continues, then significant development will be required to create the refractories used between tundish and mould in the continuous casting process.Two specific areas which will receive attention are; (I) the casting of small cross section billet s; and (2) the casting of thin slab."

Jan 1, 1990

By M. M. Kim

Zn-27% Al was pressure infiltrated into a column of 20 micron diameter abrasive grade SiC particles to give billets with particle loading of 50 voli.une %. Some billets were heated to a temperature where they became semi-solid and diluted with liquid Zn-27% Al alloy to give billets with particle loadings of 12 and 16 volume %. Some of these billets were then extruded into wire with an area reduction of approximately 98%. Tensile properties of the as-cast billets were always inferior to those of the matrix alloys; however, the extruded composite samples showed at 37% improvement in ultimate tensile strength compared to their extruded conventional counterparts. The fracture surfaces of these samples are described.

Jan 1, 1990

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By M. Misra, I. Anazia

The effects of the enzyme, peroxidase, on the sedimentation and consolidation characteristics of Florida phosphate slimes were investigated. Results indicate that pretreatment with the enzyme was beneficial for slime dewatering and consolidation. Biological activity, resulting from slime pretreatment with the enzyme, induced higher mechanical binding between slime particles.

Jan 1, 1990

By D. J. Cook, R. H. Fan, D. R. Maneval, Y-H. Shen

In this study, two placer mine processing plant effluent waters of significantly different characteristics were tested to determine the applicability of polymers along with other techniques to achieve reduced levels of turbidity. The waters from a Gilmore Creek mine and a Crooked Creek mine were characterized both as to their chemical and physical properties. The inorganic minerals were in large measure identified, and the principal cations were identified. The fine solids were studied as m their mineral identification and the extent of their electrical charges. Test work was done using polyrthylene oxide (PEO) and a liquid cationic polymer along with adjunct additives to determine optimum amounts of these coagulants for minimum consumption and optimum settling efficiency.

Jan 1, 1990

By V. C. Wittchen, T. R. Yu, J. E. Croxall

"The consolidated rockfill at Kidd Creek Mines is a weakly cemented, minus 15 cm aggregate which posed problems for conventional drill/blast drifting methods. Consequently, lateral access to mineable ore adjacent to backfilled areas was gained by drifting around the fill in shattered rock.In mid-1987, Kidd Creek Mines began to investigate means of mechanically excavating drifts in backfill . The results of this investigation led to a trial program using a Dosco MK-2A Roadheader to excavate the required drifts in backfill.The roadheader was tested at Kidd Creek Mines from July to November 1988, in 28-735 X /C to be used as the top access for drilling and blasting 32-74/ ST. During this period, the roadheader excavated 54 m of a 4.3 m by 3. 7 m arched drift in backfill. Cutting rates over the period averaged 0.8 m/cutting hour as projected with a daily high of 2.0 m/cutting hour.Wood-lagged 2-piece steel arches on 1.2 m centres were chosen as ground support for the trial. Shotcrete will be tested in a roadheader drive for its potential to improve productivity by replacing the steel arches.The trial program included evaluations of point-attack picks, two sizes of cutter motor, 20 MPa (3000 psi) water-assisted cutting, cuttings-removal systems, and environmental control devices."

Jan 1, 1990

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By Douglas C. Peters

Part of the ground control research at the U.S. Bureau of Mines is involved with improving ground control data collection and analysis methods. A geographic information system (GIs) is being used within this research effort to standardize the data collected and provide a common graphical and tabular format and analysis system for researchers to access information on underground coal mines. In addition, GIS's can perform relational analyses on multiple map and tabular data sets which are not possible through map-creation or CAD packages or through data bases alone. In addition to standardizing ground control analyses, there is an increasing need for rapid analysis of ground control data in connection with increasing production rates at longwall mines. The examination of a large number of interrelated parameters and their impact on short-term mine safety and productivity under the time constraints imposed by rapid production requires computer-aided techniques. A GIs provides the means to quickly, quantitatively, and reproducibly evaluate mine-wide conditions. This overview of GI8 techniques for mine data integration and analysis, using a mine in Colorado as an example site, will cover the input of data into a GIs, including mine-wide monitoring system data and general data such as roof control plans and geology. The methods to geographically reference these data sets and retrieve and combine them also will be covered. Automation of such processes briefly will be reviewed to allow future users to automate their mine data analyses.

Jan 1, 1990

By Perring CS, Vearncombe J. R, Ho SE, Groves DI

Large Late Archaean greenstone belts in Western Australia, Canada and Zimbabwe, contain abundant mesothermal gold, volcanogenic massive base-metal sulphide, and komatiite-associated Ni-Cu mineralization. These greenstone belts are similar in many respects to convergent and accretionary plate margins found in the Pacific rim; modem environments which are cor-respondingly rich in gold and base-metal mineralization. The giant gold placer deposits of the Late Archaean Witwatersrand Basin (the world's largest gold producer) formed in a foreland or retro-arc basin; in a similar tectonic setting to much modem placer mineralization around the Pacific. Gold and volcanogenic base-metal sulphide mineralization are abundant in Late Archaean terranes and the Pacific rim because1. gold mineralization is a product of convergent margin tectonics, and 2. accretion in convergent margin orogens provides the best chance of preserving base-metal mineralization related to submarine volcanism.It is therefore likely that the abundance of gold and base-metal sulphide mineralization in the Late Archaean reflects the widespread growth and sta-bilization of continental crust via tectonic processes broadly similar to those operating in the present Pacific basin.

Jan 1, 1990