Search Documents

By Little T. N

The Western Australian School of Mines is continuing to investigate the blasting techniques and mining strategies that are used for ore/waste separation (or high grade/low grade ore separation) or to prevent ore and waste mixing. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and undergoes no mixing of the various identified ore and waste blocks and is fully recovered at the minimum overall operating cost. The current study includes the use of computerised Knowledge Based Systems (KBS) technology to assist the user with the blast technique selection and blast design process. These aspects are highly dependent on the geology. (geometry, rock mass properties, grade distribution), explosive performance and the expectations of the mining company in terms of production rates and equipment utilisation. Most of these factors are not well defined and nor are they easy to quantify. However, a large amount of knowledge does exist and is available in the following forms: rules of thumb, empirical formulae, engineering judgement and past experience. KBS techniques are well adapted to handle such"forms of knowledge. The primary objective of this paper is to illustrate an approach for the use of Knowledge Based Systems during the analysis and interpretation stages of the blast design process. In particular, the components and methodology of the developed system are described for selective open pit gold mining. The Knowledge Based System developed was written using the declarative programming language PROLOG.

Jan 1, 1990

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

The word `environment' may have many different meanings but, for the purposes of this paper, I have assumed the definition included in the Environmental Protection Act 1986 (Western Australia). This Act defines `environment' as `... living things, their physical, biological and social surroundings, and interactions between all of these'. The Act further defines the `social surroundings of man' as `... his aesthetic, cultural, economic and social surroundings to the extent that those surroundings directly affect or are affected by his physical or biological surroundings'. This gives a very broad meaning to the idea of environment and environmental issues, and it is therefore understandable that the influence that environmental issues have on mining activity can vary so much from state to state, and even within states, and why the degree of influence can change so much with time.

Jan 1, 1990

By Keith A. Heasley

Pillar recovery in deep coal mines with competent roof and floor can concentrate stresses and generate hazardous bumps. Actual calculation of the geologic strain energy released in association with these coal bumps has been rare, although energy release values have been utilized successfully for indicating burst potential in numerous hard- rock mines. This paper advances the current knowledge of energy release calculations as applied to coal bumps through an extensive analysis of an actual bump occurrence. The U.S.B.M, displacement- discontinuity code, MULSIM/NL, is used to produce a numerical model which generates stress, displacements and energy values associated with a pillar retreat section. This model is calibrated with actual field data, and then dissipated energy values from the model are examined as to their suit- ability for indicating bump potential. Ultimately, it is determined that prudent application of dissipated energy calculations can be used as a tool to investigate the coal bump potential of a mining plan or cut sequence.

Jan 1, 1990

By Jaki Wilson, Les Armstrong, Neville T. Moxon

Low shock energy ANFO (ANFO) mixtures have been developed for use in fragmenting weak overburden materials and reducing damage.outside the blast zone in dry conditions. These mixtures can be readily produced on a minesite using conventional equipment and are formed by mixing low density additives such as polystyrene, bagasse and sawdust with ANFO.

Jan 1, 1990

By Batric Pesic

Gold dissolution with bromine was studied by using the rotating disc technique. Geobram TM 3400 was used as a source of bromine. The parameters studied were: rotating speed, Geobrom 3400 concentration, pH, temperature, sulfuric and hydrochloric acid concentration, and the concentration of various cations (copper, iron, zinc, aluminum, manganese, potassium and sodium) and anions (chloride, bromide, sulfate, nitrate, and iodide) According to the Levich plot and activation energy, gold dissolution was controlled by a chemical reaction rate. Copper, iron, and manganese in their highest oxidation states, aluminum, zinc, sodium and potassium did not have any effect on gold dissolution rate. The presence of manganous ion dramatically decreased the gold dissolution rate. Kinetic performance of bromine, in the form of Geobram TM 3400, was compared with performance of cyanide and thiourea.

Jan 1, 1990

Basic premises for evaluating special characteristics of gold-bearing porphyry metal systems stem from their contrasts with properties of the class as a whole. Included features are differences in geologic, thus tectonic, environments, subtle but real differences in the proportions of accessory metals Mo-Ag-Au that are regionally and within some regions, tempo-rally distinct, contrasts in the Ag:Au ratios, petrological-geo-chemical as well as isotopic differences between intrusive suites, the age and nature of host terranes, contrasts in alter-ation style, and zoning variations of mineralogical and physical properties of rocks. These properties are linked in various ways in different regions and suggest that in large gold-bearing systems where gold may be uniformly distributed, environ-ments of emplacement, and compositions or sources of igneous "progenitors" may dominate in importance over processes, and that systems in which gold is zoned are processes-dominant.

Jan 1, 1990

By M. Stefanakis, M. Errington, A. Kontopoulos, J. M. Prevosteau, K. Adam

The Olympias arsenical pyrite concentrate assaying 25 g/t Au, 40% S, 40% Fe and 12% As is highly refractory in nature; an oxidation pretreatment step is required to liberate gold and render it amenable to cyanidation. In the present study mineralogical analysis techniques including Image Analysis, SEM, EPMA, SIMS, Mossbauer, ICP/MS, etc., have been employed in order to investigate the mode of gold occurrence within the Olympias pyrites. Bacterial oxidation was used as a case pretreatment route and bacterially leached products were examined under SEM. The mineralogical observations and the relevant metallurgical and cyanidation test data were combined to establish a correlation between the mineralogical characteristics of the raw and oxidised products and conditions prevailing over the oxidative pretreatment step and the gold liberation achieved.

Jan 1, 1990

By Thomas P. Meloy

As the importance of particle shape in mineral processing is increasingly recognized as an major variable in predicting the behavior of both individual particles and particle systems, whether it be in dense media, froth flotation, comminution or the flow of particles, new method of shape characterization are being developed, particularly for use on image analyzers. These shape characterization methods may be broadly classified into the analytical, empirical and physical formation methods. Discussed are approaches and the strengths and weakness of each of these methods. Moreover old and new shape measuring techniques are reviewed, particularly the new image analysis methods techniques such as Fourier, Haar, Fractal, Walsh and Delta as well as a variety of other techniques such as tabling, the Cascadograph, settling and L/D ratios. Also discussed are the problems of doing shape research, current progress and the future of the field.

Jan 1, 1990

By Till M, McGee WA

The Hermit Islands are situated at 145¦ E 1 30'S in the Bismarck Sea approximately 200km WNW of Manus Island. They are dominated by basalt flows, one of which yielded a K/Ar isotopic date of 3.4 + 0.05Ma. All basalts examined were olivine-bearing, but one sample also contained hornblende. Although many outcrops were weathered, no evidence of pervasive hydrothermal alteration was observed on any islands and non-weathered rocks are petrographically fresh and many retain glass.

Jan 1, 1990

By Milner SC

Four quartz latite rheoignimbrite units (units I to IV) mapped in the Goboboseb Mountains have been traced to their eruptive source, the Messum intrusive complex; this is a complex multistage ring structure (18 km diameter) with well defined gabbroic, monzonitic, and syenitic intrusive phases, and a central ring zone containing mixed rhyolitic to latitic agglomerates. Three of the four quartz latite units are correlated with the upper and lower (2 units) Springbok quartz latites outcropping some 90-130 km north of McIsum. This implies minimum volumes of 300-500 km for wits I and III (Lower Springbok) and 2200-2600 km for unit IV (Upper Springbok). This latter unit is still ti 300 m thick at its outcrop limit, some 130 km from Messum. Each of the four units represents single cooling units. Lithologically, each can be divided into three zones: A basal, dark grey to black flinty or glassy zone, often with highly attenuated fiamme (ressembling flow banding); a central massive and strongly recrystallised zone; and an upper variable zone which exhibit breccias, contorted flow banding, and amygdaloidal to pumiceous clasts. Their overall characteristics tend to be intermediate between ash flows and lava flows. The rheoignimbrites are interpreted as the oproducts of dense, high temperature (950¦-1100 C) ash flows which underwent rheomorphism and lava-like flow prior to their final cooling.These large scale eruptions are related to the initial rifting of Africa and S. America, possiby in response to a major hot spot.

Jan 1, 1990

By C. W. Armbrust

At FHC Gold Company's Paradise Peak Mine gold and silver are produced. Precious metals recovery rates are very satisfactory along with the recovery and production of a relative high volume of mercury. At Paradise Peak precious metals are recovered via the Merrill-Crowe process and delivered to the refinery area as a mercury-bearing precipitate cake. The recovery of mercury is then obtained through a vacuum retort system. The balance of the material is mixed with fluxes and then melted and cast into dore' bars for shipping. Issues of retort capacity and concerns over efficiency led to research into the retort process itself.

Jan 1, 1990

By Windsor C. R, Thompson A, Bywater S

A new high tensile strength, steel cable, that may be grouted into boreholes has been developed for use as rode reinforcement. The manufacturing technique produces a birdcage pattern in which the cross section varies along the length of the cable. The load transfer from cement grouts to birdcage cables has been demonstrated in laboratory tests to be better than that of standard 15.2 mm diameter seven wire cables. The manufacturing process also allows for a wide range of capacities which may be specified by design engineers. The various birdcage cable configurations have been applied as rock reinforcement in a number of Australian underground and surface mines.

Jan 1, 1990

By Hutchinson H

Froth flotation is applied to mineral sand concentrates in order to produce commercially viable xenotime concentrates. Experiments indicate that a xenotime product containing 38% Y203 at 47% recovery or 34% Y203 at 83% recovery can be obtained from a 27% Y203 feed. The process involves a primary stage of reverse flotation at which oxide and silicate gangue is floated, and secondary stage of direct flotation at which xenotime is floated. Of the various collectors screened an amphoteric compound was found to be effective at both stages. This was made possible by the addition of sodium silicate at the second stage, which acted as depressant for the remainder of the gangue. Similar studies on a low grade feed material were somewhat unsatisfactory as the grade achieved fell short of what was targeted.

Jan 1, 1990

By Robert Voisey, Robert J. Spencer

"LynnGold's MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin's Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By Adams. M. D.

Most of the cyanide lost in carbon-In-pulp plants is due to the reaction of cyanide with base metals and sulphides during leaching. Some cyanide is also lost in the adsorption tanks as a result of oxidative and adsorption reactions with the activated carbon. The high rates of cyanide loss in the elution and electrowinning stages are atributable to hydrolytic decomposition and anodic oxidation, respectively. However, the relative amount of cyanide lost during these two stages is small for a given amount of ore treated.

Jan 1, 1990

Milling Practices Ore is direct tipped into a gyratory crusher and crushed to minus 209mm and fed to stockpiles for the blending of grade into the mills. Secondary and tertiary crushing reduces the mill feed to minus 12mm. Mill feed is a blend of breccia and porphyry ore into two primary mills with the overflow to a regrind mill and then into the leach tanks, followed by a conventional counter current carbon in leach circuit. Underflow from the cyclones feeds back into the primary mills for additional grind. An unusual feature of the Mt Leyshon milling circuit is a desire to produce scatts. The scatt by product is the polished base rock of the Mt Leyshon Breccia clast and contains little grade. These scatts are produced because of the additional time and energy required to produce a proportionally small quantity of gold. The residence of these scatts in the mills decreases the mill feed rate. Scatts account for twenty percent of the mill feed and are screened from the discharge of the primary mills.

Jan 1, 1990

By P. G. Semple, K. W. Major, R. M. Nendick

As free milling oxide gold ore reserves are depleted, more mining companies are having to evaluate the available alternatives for treating refractory deposits. The selection of a treatment process can be very difficult; and, despite the claims of their respective proponents, there is no one process that will continuously prove superior. Selection of the optimum process for an individual deposit is contingent on the size of the deposit, the grade of the deposit and the refractory nature of the ore. Since extensive metallurgical test programs are usually required to determine the optimum extraction process, an inappropriate initial selection may prove costly and time consuming. This paper discusses the steps involved in evaluating a refractory ore in order to expedite the evaluation of the required process through the feasibility study stage.

Jan 1, 1990

By B. Madelin

Over the last ten years, Minemet Recherche and Metaleurop have used an approach in order to investigate and improve the operation of its Smelting furnace and its lead blast furnaces. This approach gives importance- to three complementary means of investigation : - Probing campains in the industrial furnace (temperature and gas analysis profiles), - Chemical and physical modeling (coke combustion, sinter reduction modes, flows patterns, ?.) , - Staged mass and heat balances or kinetic model. This allows to define the limits of operation of each blast furnace and to predict the influence of operating parameters on the furnace performances. For the zinc Imperial smelting furnace, the probing results show the existence- of both an Isothermal reserve zone at 1015ºc and a chemical equilibrium between ZnO and gas which makes possible the use of a practical model for heat and material balances. In particular, very good prediction on the influences of operating parameters can be made. On the contrary, for lead blast furnaces, the probing results show that the thermal and chemical equilibria are not reached. Consequently, classical models for staged heat and mass balances are not sufficient. The use of the other means allows then to characterize the specific influences of operating parameters on the thermal instabilities of these furnaces and their allowed limits.

Jan 1, 1990