Search Documents

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

In the past ten years or so there has been a renewed interest worldwide in the processing of refractory gold ores. The Archean province of Western Australia contains both numerous and major gold deposits, and has a long history in the development and practise of treating refractory ores (eg Blaskett and Woodcock, 1953). Depletion of shallow oxidised ores in recent years has re-focused attention on deeper sulphidic ores, and as a consequence has renewed interest in treatment methods for those ores which are refractory. Mineralogical factors he at the heart of reasons as to why these ores are refractory, and are the key to designing and improving treatment options in the longer term. This paper presents an overview of mineralogical factors that are relevant to the processing of refractory gold ores in the Archean of Western Australia. It is based on a number of research projects and other work on a variety of gold deposits, mainly in the Eastern Goldfields region, carried out over the past five years or so.

Jan 1, 1991

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By Deepak Malhotra

The economic viability of mineral companies not only depends on maximizing mineral recoveries but also on their ability to do so at minimum cost. Increasing pressure to cut costs has resulted In reduced staff, thereby decreasing the capabilities of routine metallurgical audits. This paper reviews a systematic approach to plant auditing which has been used successfully at several operations. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1991

By Valerie A. Rhodes, Catherine T. Aimone

Often blast damage litigation involves structural damage which clearly is not blast related. The fact that structures are observed to be damaged when blasting has taken place in the near vicinity of these structures does not necessarily mean that the damage was caused by blasting. If careful blasting and seismograph records were kept by the blaster which decisively indicate damage is not blast related, then other causes of structural damage need to be assessed. These include problematic soil characteristics and long-term changes in climate or subsurface soil moisture. This paper presents the evaluation process required to investigate soil problems leading to damage often attributed to blasting.

Jan 1, 1991

By N. B. Aughenbaugh

Compacted, fine-grained soils, often referred to collectively as clays, are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials for these liners include a variety of sand, silt and clay admixtures. These exhibit dramatically different engineering properties when densified. Therefore, it is imperative to adequately assess and characterize any soils being considered for compacted liners. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Because they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners also must include an evaluation of their flexibility. That is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1991

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

By J. J. Schwoebel, M. J. Mavor

Rapid coal extraction techniques in gassy mines may strain a ventilation system if a degasification approach is not utilized. Design of mine ventilation systems requires estimates of gas emission rates from unmined coal into the existing mine workings. A degasification system for a specific property can be properly engineered to improve mining economics if the proper geologic and reservoir information is collected. This paper describes methods to determine the degasification rates for horizontal boreholes and vertical (stimulated and unstimulated) wells and the rate of gas emissions into the mine workings. The methodology is demonstrated by a specific example. Horizontal boreholes drilled in advance of mining are demonstrated to be the most effective means of coal seam degasification and reduction of gas emissions into mine workings. The significance of the paper is that few published methods for these estimates are available

Jan 1, 1991

By Robert B. Parsons

"Exploration and development of mineral resources in developing countries by Canadian-based multinational mining companies is becoming increasingly common. One problem being encountered is that the objectives of the governments of developing countries can differ from those of developed countries. These objectives are not always consistent with maximizing returns from the projects, which can create conflicts between the mining company's responsibility to its shareholders and the desire to be a good corporate citizen. This article discusses how a mining tax regime can be designed to make the social goals of a government consistent with the economic goals of the company.IntroductionAt the recent International Seminar on Mining Taxation organized by CIM and the United Nations there was considerable discussion about the role of international mining companies operating in developing countries. Not surprisingly, given the diversity of backgrounds of individuals attending the Seminar, there were different opinions about what this role should be.Government PositionRepresentatives of governments pointed out the strong desires of their countries for technology, high-level technical training of their workforce, increased employment, and development of social infrastructure. They pointed out that, to a large extent, these objectives could be more efficiently met by mining companies operating in the country than by the governments themselves. For example, a multinational mining company (""MMC"") would have extensive knowledge of the various technologies available, and would have performed a detailed evaluation of the mineral resources before choosing the most cost-efficient technology for that project. They would, therefore be in an ideal position to assist the country in importing and developing such technology. Similarly, the company could provide opportunities for hands-on training, both at the technical and managerial levels, which would otherwise be unavailable to the government."

Jan 1, 1991

By Riches N, Harbort G

The Jameson flotation cell was developed jointly by Mount Isa Mines Limited and Professor GJ Jameson of the University of Newcastle. The cell has been used in a number of cleaning applications within Mount Isa Mines Limited. In 1989 Peko Mines tested the Jameson flotation cell at the Warrego concentrator to upgrade recleaner concentrate. 2 x 1.4 m diameter Jameson flotation cells were installed in 1990. This paper describes the testing, commissioning and operation of these Cells.

Jan 1, 1991

By John R. Woodcock

The Kitsault molybdenum deposit lies along the east margin of thecoast Batholith Complex near the head of the fiord of Alice Arm. It is 800 km (497 miles) northwest of Vancouver, British Columbia. The deposit is located on Lime Creek 8 km (5 miles) from the coast on a wide dissected upland valley at an elevation of 600 m (1969 ft). It is an area of coastal rain forest with high annual precipitation and extremely high winter snowfall. Although the area is of high relief, outcrops are largely restricted to ridges and canyons. Most of the area is covered by the coastal vegetation or wet swampy upland areas. The south edge of the molybdenum deposit was exposed in a sharp canyon; however, outcrops over the remainder of the deposit were largely restricted to a few small exposures of resistant hornfels. The mineralization is related to an elliptical porphyry stock of 52.3 m.y. age which intrudes argillites and microgreywackes of the Late Jurassic Bowser Group. A circular zone of alteration, with a diameter of about 700 m (2297 ft), occurs in the north end of the stock and the molybdenite mineralization is concentrated in the outer parts of this zone of alteration. Thus, the northern part of the mineralization occurs partly in the hornfels and partly in the stock, whereas the southern side of the ring of mineralization cuts across the middle of the stock. Zoning within this system includes a central circular area of almost complete replacement of quartz plus K- feldspar and this grades sharply outward into a phyllic zone. Clay alteration is largely localized along late faults. The ring of molybdenite mineralization is partly overlapped and partly surrounded by a zone of pyrite mineralization. Some chalcopyrite is coextensive with the pyrite zone. Late polymetallic veins fill two conjugate fracture sets. These quartz veins contain galena, pyrite, some chalcopyrite, and a number of lead-bismuth sulfosalts.

Jan 1, 1991

By Ogilvie M

South Bulli is the oldest and largest underground coal mine in Australia. Two longwall units are in operation and current production is 2.5 to 3 million tonnes of run of mine product per year with a workforce of 600. Prior to 1984 a workforce of around 1,200 produced 1.5 million tonnes. Advances in technology can. of course, account for some of this gain, but the changes made in the human resources area are also seen as playing a major role in South Bulli emerging as a reasonably stable operation.The human resources strategy adopted recognises the value of the workforce and is aimed at not only fostering cooperation as all levels, but also making employees aware of the direct contribution they can make to the success of the enterprise.

Jan 1, 1991

By John T. Aler

The U.S. Bureau of Mines has been studying the problem of why explosives detonate weakly or misfire during blasting in underground coal mines. Cross-borehole shock wave interaction has been identified as a predominant mechanism causing explosives to function improperly (1)(Underline numbers in parenthesis refer to items in the list of references at the end of this report.). Cross-borehole shock wave interaction can be simulated in a laboratory setting, making possible the replication of tests in sufficient numbers to understand and quantify some of its effects on permissible explosives (2). The work presented here investigates the capacity of explosives to partially recover from the desensitizing influence of the shock wave. The recovery trend of different explosives can indicate optimum blasting patterns useful for minimizing borehole charge malfunctions.

Jan 1, 1991

By B. K. Parekh

The International Symposium on Comminution was organized at Camborne School of Mines, Cornwall England. Papers covered the fundamental and practical aspects of comminution in the mineral industry. Although comminution equipment design has not changed fundamentally during the last 50 years, methods of control and optimization have improved considerably. A simulation model for batch ball milling in the rotating mill was developed as a step toward continuous simulation of ball and autogenous milling. New concepts in jaw crusher technology design and the concept of a 1.6- x 2.1-m (66- x 84- in) jaw crusher with open feed throat has resulted in power savings. The use of cone crusher technology in comminution circuits with particular reference to machine design, plant flowsheet and control figuration has been reported by Boliden Allis, of Sweden. The Whiten steady state crusher model form has been used to develop a quantitative model of 2.1-m (7-ft) cone crushers. This was done by incorporating liner age (wear) and liner length as variables on the selection of particles for breakage and thus on the product size distribution. Another paper by Lira and Karetsky discussed the development of a model based on a multisegment ball mill developed by Whiten and Kavetsky. It is capable of simulating the performance of a coarse grinding ball mill of a given diameter, ball size and mill speed.

Jan 1, 1991

By Budden J. R, Rhodes M. K

Bacterial oxidation technology was successfully applied in a mine site pilot plant for the treatment of refractory gold concentrates. The bacterial culture was proven capable of selectively breaking down the refractory sulphide minerals to release the gold. Gold extractions greater than 90 per cent were possible when oxidised concentrate was leached with cyanide solution. The pilot plant was designed using data scaled up from laboratory testing and sized for transport by standard vehicles. The bacterial culture used to break down the refractory gold-bearing mineral was a natural mixed culture able to withstand temperatures up to 55¦C, thus making the technology particularly suitable for use in Australian and in some North American gold mining regions. The pilot plant was operated at the mine site over a six month period. Performance of the bacterial oxidation technology under site conditions was as predicted from the laboratory testing. It was demonstrated that the culture was robust under normal site condi- tions and that the culture could withstand wide variations in the feed and the operating conditions, while still achieving satisfactory oxidation levels. The technology was able to be utilised by site operators and supervisors with minimum intervention. Design data for a commercial facility was collected for a number of different concentrate samples and a feasibility study completed. Estimated capital and operating cost have been obtained.

Jan 1, 1991

By R. Hogg, M. Polat, S. Chander

A fresh dust generator was designed and built in order to study the agglomeration behavior and other characteristics of freshly generated airborne dust. The size distribution of the freshly generated quartz airborne dust produced by the generator was measured both directly in air and after dispersion in water. It was observed that same dust particles had an apparently coarser size distribution in air than in water, suggesting possible agglomeration of the dust particles. It was also observed that the size distribution obtained by a cascade impactor was very similar to the liquid dispersed size distribution, implying deagglomeration by the impactor. The agglomeration was confirmed by microscopic observations of particles in air and those collected on a microscope slide. The extent of agglomeration played a decisive role on the fraction of the dust actually becoming airborne. It was also found that contamination of the airborne dust by the rolls of the crusher was almost twice as much as that of the product.

Jan 1, 1991

By Wang Yingmin, Xu Zhuyun

The optimum of general mine ventilation networks is very difficult and has a considerable significance. Based on the content model, this paper presents a more general nonlinear programming model whose number of variables equals that of independent meshes. The constrained conditions are linear inequalities only. The model is changed into an unconstrained problem with multiper method. The optimum results are computed with DFP algorithm and the Improved Golden section method is used in its linear searching. The computer program written in Quick BASIC is suitable to the optimum of any type of large mine ventilation networks with different regulating devices. The paper presents two examples for optimum of ventilation networks.

Jan 1, 1991

By Gerald A. Zicg

The Sheep Creek project area lies between 15 and 20 miles north of White Sulphur Springs in west central Montana, on the southern flanks of the Little Belt Mountains. The Sheep Creek project is a joint venture in which Cominco American Resources, Inc., has a 50% operating interest and BHP-Utah International, Inc., has a 50% participatory interest. The property consists of over 40,000 acres of leased fee land and lode claims. Modern exploration of the Sheep Creek area began in 1973 and 1974, when Homestake Mining Co. examined the extensive Sheep Creek gossans with soil sampling, trenching, and drilling. Cominco American Inc. began exploration in the area in 1976. Between 1978 and 1985, Anaconda Copper Co., Exxon Minerals Co., and Freeport also conducted exploration programs in the area. In 1985, Cominco completed consolidation of the district, gained BHP-Utah International, Inc., as a joint venture partner, and the joint venture drilled the first significant copper mineralization on the property. Of six bodies of copper mineralization so far located, the best defined are an upper copper zone, which includes a probable resource of 4.5 million metric tonnes grading 2.5% Cu and 0.1 % Co, and a lower copper zone which includes a possible resource of 4.5 million metric tonnes grading 4% Cu. Exploration drilling of the property is in progress.

Jan 1, 1991

By K. R. Wood, P. M. Blythe, J. A. Finch, M. L. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1991

By G. E. Wasson

Consolidation Coal Co. tested the agglomeration of fine coal using a laboratory pellet mill. The principal operating variables examined were feed coal moisture, coal size distribution, and additives to the feed coal. The moisture of the feed coal was found to be critical to both the pellet mill operability and the product strength. Coals, with feed moistures too high to pelletize, could be pelletized if mixed with lime or a water absorbent material. The addition of dry starch binder improved the product strength.

Jan 1, 1991