Search Documents

By Lawson F

Synthetic calaverite (Au Tez) has been prepared and its physical properties checked.Simple flotation tests indicate that the recovery of calaverite should be possible using n-butyl or sec-butyl xanthate collectors under approximately pi I neutral conditions with a copper sulphate activator.Roasting calaverite in air at moderate temperatures resulted in its decomposition with the formation of elemental gold and tellurium dioxide.In alkaline oxygenated cyanide solutions, both gold and tellurium tend to dissolve. At pHs less than 14, about 50 per cent of the tellurium remains as elemental tellurium; however in very strongly alkaline solutions, essentially all of the tellurium is converted to the soluble tellurite ion (TeOl-).However, even at high pHs, the solubility of gold in the cyanide solution is still low due almost certainly to passivation effects.

Jan 1, 1991

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

Good morning ladies and gentlemen. It gives me great pleasure to talk to you today about a pet subject of mine, on when to mill and when to leach gold ores. According to Gold Fields Mineral Services of London, gold production in the United States in 1989 amounted to about 8.5 million ounces (259t), an increase of 29 per cent over 1988 and 67 per cent over 1987. The U. S. Bureau of Mines reports that from the major producing states of Nevada, California, Montana, and Alaska, some3.2million ounces of the 1989 production were produced from milling gold ores and 2.3 million ounces from heap or dump leaching. Ap- proximately 45 million tons of ore were milled and 140 million tons of ore were heap or dump leached.

Jan 1, 1991

By Mwaba CC

Ok Tedi Mining Ltd has been using flotation for the production of copper/gold concentrates from a complex copper sulphide ore for several years. During this period, much effort has been devoted to metall- urgical treatment of the ore. This paper examines some of the mineralogical aspects of the sulphide minerals in the ore using the electron microprobe analyser. Results have revealed the complexity of the copper sulphide minerals and in particular, chalcocite. Analysis of both plant and laboratory flotation products has provided further insight into the effects of mineralogy on the flotation of copper and iron sulphides. A significant observation is that some of the pyrite minerals apparently exhibit natural floatability. The implications of the mineralogical characteristics of the sulphide minerals on the flotation of the ore are also discussed.

Jan 1, 1991

By Corby G. Anderson

Since 1985, the Sunshine Mining Company has used a patented nitric-sulfuric acid pressure leaching system for production of silver and copper from a refractory sulfide ore body. To better understand this novel process, a program of lab scale testing was undertaken to quantify the effect of system variables on silver recovery. Some of the factors studied include temperature, agitation, acidity, vessel pressure, particle size, percent solids and oxidizer amount. In turn, this knowledge will be applied in actual plant practice to upgrade reaction time, increase concentrate throughput, raise silver recovery and lower reagent costs. A discussion of plant process changes resulting from lab scale testing is included.

Jan 1, 1991

By Clarke DS

The igneous intrusions in SE Papua New Guinea are part of a sub-volcanic to plutonic, high-K calc-alkaline to shoshonitic suite. High-K andesitic to dacitic intrusives on Misima and Woodlark Islands, and shoshonitic intrusives in Milne Bay and the eastern Owen Stanley Ranges are related to late Cenozoic andesitic volcanism. Both suites are associated with epithermal Au-Ag deposits and weak porphyry Cu-Au mineralisation. All significant alluvial and lode gold occurrences in the region are spatially related to intrusions. Intrusions in the D'Entrecasteaux Islands and near Mt Suckling are core plutons related to basement doming, and appear to have no association with either volcanism or hydrothermal mineralisation. The core plutons are not petrochemi:ally distinct from the volcano-re:-ed Intrusions.

Jan 1, 1991

By Bengt H. Fellenius

It is a truism that in the design of pile foundations one must consider both capacity and settlement. As to capacity, most basic text books contain simple methods of design of capacity of single pile. More sophisticated methods are the subject of many journal papers. However, methods for design considering settlement of pile foundations are scarce. (Most confuse settlement with the movement due to load-transfer?the transfer of load from the pile to the soil). Furthermore, for both capacity and settlement, most methods include several simplifying assumptions regarding soil layering and neglect the effect of the frequently occurring fill and excavations, as well as changes of the groundwater table and pore pressure distribution. Therefore, the methods may provide qualitative results, but not quantitative. Because of this situation, pile design often appears as somewhat of a guessing game and a very subjective?and risky?occupation. This need not be. Pile foundation design is controlled by three factors: capacity, strength, and settlement requirements and these have been combined in a method called "the unified design of piles and pile groups considering capacity, settlement, and negative skin friction" (Fellenius, 1984; 1989), which method is summarized in this guide.

Jan 1, 1991

New Celebration Gold Mine is located 35 km SE of Kalgoorlie, Western Australia, in the Archaean Kalgoorlie-St Ives Greenstone belt. The leases total 119 sq kms and arepart of a joint venture between Newmont Australia Ltd (as manager) and Mt Martin Gold Mines N.L. Mining commenced in August, 1986 and is now producing over 115,000 ounces of gold per annum. A variety of gold mineralisation styles with a total resource of 23.5 million tonnes at 2.19g/t are associated with shear zones at New Celebration. Gold production is co-ordinated from 7 open pits with others planned to com- mence soon. A large scale underground trial mining operation has com- menced with a decline on the hanging wall of the main producing orebody, Hampton Boulder. Millfeed produced is classified on the stockpile according to grade and metallurgical performance and blended tomaximise throughput while main- taining grade through a CIL treatment plant currently operating at 1.7 million tonnes per year.

Jan 1, 1991

By Joseph M. Denk, Gary J. Wirth

This paper summarizes a three phase face ventilation study which was conducted from September 1989 through March 1990 to determine face area methane liberation patterns on two extended longwall sections. The coal seam being mined was considered gassy and the mine liberated an average of 14.4 million cubic feet per day (cfd) or 0.41 million cubic meters per day (cmd) of methane through the mine fans. The mine also used an extensive underground degasification program to recover up to 13.4 million cfd (0.38 million cmd) of methane. Data was collected while the longwall sections were mining from the beginning, middle and end of panel extraction to determine the relationship between the methane liberation and extent of longwall retreat. As expected, methane concentrations did increase from the headgate (intake) to the tailgate (return) side of the longwall face and peak concentrations were detected above the shearer as it passed a methanometer location during mining. There were significant differences in the methane liberations due to the location of the active face within the longwall panel. Results from this study could be used to determine a minimum design face air quantity for an extended longwall section operating under similar conditions.

Jan 1, 1991

By Majorkiewicz A

Engineering of gold treatment facilities complete with infrastruc- ture in a remote location such as Papua NewòGuinea present unique problems to the design team. Site location, topography, ground conditions and infrastructure are some of the major hurdles to overcome when setting out on the design of such plants. This paper discusses two such plants, located in two distinctly different areas of Papua New Guinea and the solutions evolved in order to design successful operating facilities.

Jan 1, 1991

By O E. Crenwelge

Seismograph measurements are usually made near blasting operations solely for the purpose of monitoring compliance with governmental regulations. However, recordings of seismograph signals have far greater potential than this, if the proper procedures are used for analyzing the transient data.

Jan 1, 1991

By H. L. Jessberger

In recent years piled raft foundations of multi-storey buildings on weak soils have generated much interest and discussion. By taking account of the effects of each component of the system - the pile group and the raft - it is possible to reduce the settlements and inclinations of the system and to have an expedient load distribution on the piles and the raft. Thus the structural design of the foundation can be optimised.

Jan 1, 1991

By Floyd W. Crump

New technology in video equipment, such as Super Video Tapes, Super Video Camera Recorders equipped with high speed electronic shutters, and VCR's with editing capabilities make it possible to resolve high speed events to still frames with an event elapsed time of 17 milliseconds (ms). This is far from the 2 ms resolution available with a High Speed 16 mm Film Camera such as the LOCAM at its maximum 500 frame persecond speed, but is adequate for many field blast evaluations.

Jan 1, 1991

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

This list of corrosion-related terms was compiled to encourage the use of the correct terminology, and to serve as a handy reference for students. It Is based on a similar list compiled by the National Association of Corrosion Engineers (NACE). To promote bilingualism, the Afrikaans terminology is included (in italics at the end of each entry).

Jan 1, 1991

By J. H. Lalor

The Olympic Dam deposit was discovered in July 1975 with the intersection of 38 m (125 ft) of 1.05% copper in diamond drill hole RD 1. A further eight holes were drilled with only marginal encouragement to November 1976 when RD 10 cored 170 m (558 ft) at 2.12% copper and an economic discovery was confirmed. The discovery of Olympic Dam is an excellent example of the application of broad-scale scientifically based conceptual studies to area selection combined with the backing of an exploration management willing to support its exploration scientists in testing their ideas with stratigraphic drilling. It also illustrates the persistence required in mineral exploration. The project began in 1969-1972 with the development of a conceptual model for the formation of sediment-hosted copper deposits. This model suggested that the alteration of continental-type basaltic rocks could release copper into solution from which it could be concentrated in favorable stratigraphic positions. In mid-1972, this concept was applied to a review of the Proterozoic and Lower Paleozoic rocks in South Australia aimed at defining targets for stratigraphic copper deposits.

Jan 1, 1991

The reduction in the number and duration of machinery and equipment failures is an important source of economical efficiency enhancement in the Polish coal mining industry.Non-dismantling methods have been thus developed to evaluate the technical state of machines. Among these viroacoustical methods are the most effectively employed. Two-directional organisation of the testing can be chosen, such as periodical and continuous inspection. The monitoring methods for ball bearing, rope tension uniformity, longwall shearers, main fans and shafts installations etc. Instrumentation for monitoring measurements are either of intrinsically - safe or explosion - proof construction, which enables using them in a gas-hazard atmosphere. The development of these procedures has led to the trials to insert the diagnostic methods into the organisational scheme of a coal mine.

Jan 1, 1991

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

Two types of low-sulphidation epithermal mineralisation may be recognised in volcanic terranes. Chalcedonic Silica- Adularia-Illite type mineralisation is most common in rhyolitic terranes, whereas Crystalline Quartz-Illite-(Adularia- Kaolinite) type mineralisation is more typically formed in andesitic terranes. A third type of epithermal mineralisation, the high sulphidation or Vuggy Silica-Alunite- Kaolinite-Illite type, is also common in andesitic terranes. Episodic violent boiling, accompanying hydraulic fracturing and hydrothermal eruptions, characteristic of geothermal systems in rhyolitic terranes, is stressed for the formation of Chalcedonic Silica mineralisation. Such boiling of deeply circulating meteoric groundwater, with some magmatic fluid contribution, provides chalcedonic veining, episodic banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S from the fluid to cause major gold deposition. Crystalline Quartz mineralisation is probably caused by the mixing of shallow acidic groundwater with ascending deep geothermal fluids beneath andesitic strato- volcanoes. The cooling effect, oxidation, and increased acidity, overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of metals. Extensive formation of base-metal sulphides further enhances gold deposition. Violent boiling is restricted to local structural dilation sites, potentially producing high grade "bonanza" gold mineralisation.

Jan 1, 1991

By M. ]. [Mohkam

The paper describes the features of the problems encountered and the countermeasures taken for two different tunneling projects. Where, slurry shields were used to excavate, in soft heterogeneaous water-bearing grounds, tunnels passing at very low cover beneath existing foundations of H.T. electric pylons, underground structures and major utilities. In order to avoid any ground failure and/or damage to the existing structures, one option was ground treatement by grouting or freezing technics. However, it was judged that, based on previous experiences, excavation with slurry shield could be carried on securely using an appropriate slurry enriched with polymers and applying a well determined pressure at ground face. A three dimensionnal limiting equilibrium analysis model was used to determine proper confinement pressures. And, the appropriate slurry compositions were stabilished based on laboratory test results. The tunnels were excavated successfully, no ground failure was experienced, and the maximum settlement recorded (on pylons) didn't exceed 3 mm.

Jan 1, 1991