Search Documents

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By Prof. Dr. T. R. Boulos

The Egyptian marine phosphorite of Sebaiya West, the Nile Valley, consisting of both non-oxidized hard siliceous and oxidized leached friable ore types, is subjected to a roughing-cleaning silica flotation circuit for production of wet-process phosphoric acid concentrate. Operating at its maximum capacity of 268 t/hr, the following were the main problems encountered during the early stages of running the plant: 1. The tremendous amount of slimes generated by scrubbing the crushed ore causing turbidity in the plant thickener after a short time of operation, regardless of the added flocculant. 2. Rod mill choking leading to inefficient performance of all other equipment and poor flotation results. 3. The drastic increase in imported oleic acid price. Pulp density and slurry flowrate measurements at different points of the plant as well as ore microscopy, size distribution analysis, chemical analysis and x-ray diffraction analysis of representative ore samples coupled with Work Index measurements of feed samples showed that the wide variation in the ore's hardness was responsible for such problems. Application of the locally produced non-edible rice bran oil as a substitute to imported oleic acid in flotation resulted in total saving of U.S.$2 million in 1990. The total unsaturated fatty acid content of the oil is high, ranging from 75.2 to 81.5 mole % of which the C18-unsaturated fatty acid content ranges from 72 to 79 mole %.

Jan 1, 1993

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

By Broderick E. Davis

Each year, about 45 Mt (50 million st) of flotation tailings are discarded in Florida phosphate operations. These tailings only contain about 4% of the phosphate in the ore. However, more than half of the phosphate in the tailings is concentrated in the +600 µm (+28 mesh) size fraction at grades of up to 20% P205. Many phosphate producers have attempted to solve this problem by floating the +425 µm (+35 mesh) flotation feed separately. However, phosphate recoveries in these circuits are typically only 60%. For seven sampled phosphate operations, the phosphate content of the +600 µm (+28 mesh) fatty acid tailings ranged from 15% to 25% P205. In every case, the +600 µm (+28 mesh) fatty acid tailings was higher in grade than the overall flotation feed. Attempts to efficiently recover this coarse phosphate have apparently been unsuccessful at these seven phosphate operations. Recovery of this coarse phosphate would provide an additional 900 kt to 2.5 Mt (I to 2.7 million st) of phosphate annually and add an additional year to the reserves of these important deposits. A typical central Florida phosphate matrix is composed of three different mixtures of minerals. The +1.18 mm (+ 16 mesh) portion is chiefly phosphate pebbles and is beneficiated by sizing. The -106 µm (-150 mesh) portion contains virtually all of the clay minerals and is discarded in the hydrocyclone overflow. The -l mm +106 µm (-16 +150 mesh) material is a mixture of quartz and phosphate minerals.

Jan 1, 1993

By Bruce W. Downing, Philip G. Claridge

"The availability of environmental data is a major concern in the development of an exploration project through the permitting and feasibility stages. The collection of these data should ideally start very early in a major exploration program. Although a large proportion of the environmental data can also be used for exploration purposes, (e.g. stream-sediment, soil, and rock analyses), environmental sampling will rarely have been initiated at an early date. For the Windy Craggy project, a major environmental concern is the potential for generation of acid rock drainage from waste-rock piles. The project is reviewed with respect to the environment of the deposit, deposit geology, mineralization and reserves, the sequence of exploration activities to the present, the potential for the development of acid rock drainage, the geochemistry and water quality, and the integration of exploration and environmental databases and their application to environmental planning. IntroductionIn the classical sense of exploration of a mineral deposit, the efforts throughout exploration are routinely directed at confirming the existence of the deposit and defining its extent, grade and continuity. Environmental issues are usually tackled separately, possibly by different personnel at a later date. When that is the case, an opportunity is lost to build, from an early date , a comprehensive database that (I) will satisfy the needs of conventional exploration and environmental monitoring, and (2) is usable as a predictive tool for environmental impact assessment.The concept of environmental geochemistry is not complex. The availability of environmental data is a major concern in the development of an exploration project to the feasibility and permitting stages. The collection of data should ideally start very early in any major exploration program. In many cases a significant proportion of the geochemical exploration data gathered early in the life of a project will also be used later for environmental purposes (e.g. stream-sediment, water, soil, and rock analyses). Rarely, however, will the data gathered in a geochemical exploration program provide information as complete as that attainable if environmental objectives had been considered in scoping the work.A knowledge both of local and regional geochemical processes can lead to a better understanding of environmental impacts. This understanding is the basis upon which good environmental management practices may be built. Geddes Resources Limited has undertaken a major study of the natural environment in the Windy Craggy area which includes geology, surface and underground waters, soils, stream sediments, glaciers and geomorphology (Geddes Resources Limited, 1990). This paper deals with the building and integration of the exploration and environmental databases."

Jan 1, 1993

By Nelson G

The construction and placement of tunnels by means of jacking is continually advancing. This paper presents an outline of the construction of a major highway tunnel placed by a combination of mining and progressive placement by hydraulic jacking of precast units. Features of the project were the relatively shallow ground cover between rail and road routes over the tunnelling and jacking operations and also the weight of tunnel sections to be moved into position.

Jan 1, 1993

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By Reichardt Y

Fine feed fractions in the size range from 1 to 40 ¦m of materials with different hardness as limestone and silicon carbide have been stressed in two different devices. A tungsten-carbide-blodc allows a single stressing with a pressure up to 2000 MPa and a 4-piston-block enables a multiple stressing procedure in which the material bed is stressed in alternating directions with a pressure up to 700 MPa. The experiments show energy absorption as the major factor for the interparticle breakage of hard material, like quartz, zircon silicate, silicon carbide and smelted oonindum, pressure, however, does not influence the results within the investigated range from 100 to 700 MPa and even up to 2000 MPa for corundum. But the breakage of the middle-hard limestone depends on the pressure so far as more fineness can be produced if the same energy is introduced at a lower pressure level. The creation of very fine and microfine fragments decreases strongly with increasing hardness of the feed materiaL The energy consumption for producing microfine material with a multiple stressing procedure on a particle bed is much lower than that one of a usual milling process. But this procedure needs a classification with a seperation cut at a couple of microns, which is not easy to accomplish.

Jan 1, 1993

By Robert E. Moore

Synthetic spinel is proving to be a highly effective refractory for specific applications, but its cost limits applications. Formation of spinel from a raw material such as diaspore or bauxite could provide a simple and less costly starting material. In the study reported here, finely ground (-325 mesh) diaspore from Missouri and bauxite from Guyana and China are combined with hard burned MgO (-325 mesh) in appropriate proportions to yield spinel and spinel with secondary phases. A classical sintering and dilatometer study was completed, followed by a microstructure study to determine completeness of the reactions and morphologies of the reaction products.

Jan 1, 1993

By R. D. Grove, M. F. Elliott, R. L. Weigel

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators' vision when major deviations occur. An image analysis system has been developed by IMC Agrico Company (IMCA) to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By G. F. Raymond

Discussion by G.F. Raymond Knudsen's study presents two curious conclusions: • The kriging of blasthole assays can systematically overstate mill head grades by as much as 21% as a result of unbiased sample variance. • No estimation method is able to reduce this bias to a small margin. The study is based on a simulation using real data and what are presumed to be actual variogram parameters from a real deposit. Although I have no doubt that the first conclusion (21% overestimation) is correct for the author's simulation, I do not believe this represents a realistic mining situation. Over the past 15 years I have done extensive comparisons between exploration drill-hole assays, blasthole assays and mill head grades on seven major open-pit mines, including some very erratic gold deposits. Commonly, nugget effects on blasthole variograms were 10% - 20% higher than on exploration variograms. And in one extreme case, the difference was 50%. Even in the extreme case, ordinary kriging on blastholes agreed well with the mill head grade over the long term. In Knudsen's simulation, the blasthole nugget effect is assumed to be 200% higher than exploration data's. He supports this by variogram plots from each. My guess is that the apparent, large difference between these variograms results from a failure to account for the proportional effect (blasthole assays are likely from a higher-grade area). A simple check would be a comparison of the variance of exploration samples nearest blastholes. As for a nearly conditionally-unbiased estimator of a large random error, the arithmetic mean of all of the data certainly qualifies, provided there is an even data spacing. As a corollary, so does simple kriging, which would include, in this case, a large weighting to the arithmetic mean. Similarly, using a large number of samples with ordinary kriging or indicator kriging would significantly reduce the bias in the case of a large nugget effect for the variogram.[ ] Reply by H. Peter Knudsen Raymond questions two conclusions in the paper. First, he wonders whether a 21 % overestimation represents a realistic mining situation. I agree that 21 % is high, but overestimation in the range of 10% to 15% is certainly common in my experience. Furthermore, several years ago I consulted on a gold mine that was experiencing a 45% overestimation due, predominantly, to poor blasthole samples: In further questioning of the 21 % value, Raymond wonders whether the nugget effect of the blastholes is really so much larger than the nugget values of the exploration data. It is consistently larger throughout the deposit. In my experience with six Nevada gold mines, the high nugget value is not unusual. In fact, for some reason, nugget values for blasthole samples are typically about 0.0005 (opt squared). I am of the opinion that this high nugget effect observed at many gold mines is predominantly due to the inherent inadequacies of the blasthole sample and subsequent sample preparation. The second conclusion Raymond questions is the inability of the estimators tested to reduce the conditional bias. In fact, the conditional bias is extreme with the polygon estimator and greatly reduced by ordinary kriging. However, it was not eliminated. Raymond suggests using simple kriging, or perhaps a larger number of samples, to reduce the conditional bias. The technique of simple kriging may be less affected by the random errors in the data, but I did not test the technique. Using a larger amount of data presupposes that too few samples were used initially. In ordinary kriging and indicator kriging, the screen effect comes into play and ensures that samples beyond the second screen are given zero weight. Hence, increasing the sample size does not change the estimates nor the conditional bias. The main point of my paper is that the random unbiased errors (a fact of life in blasthole samples) cause a conditional bias in our estimates. The mechanics by which the conditional bias is introduced are nicely explained by Springett. My paper simply shows that the bias is also present when working with linear estimators, such as ordinary kriging, and even with nonlinear estimators, such as indicator kriging.[ ]

Jan 1, 1993

By J P. Ashby

Compared with elsewhere in the world, New Zealand quarries have tended to be mostly small. The reasons for this are a combination of the relatively high transport costs, low population density and a pioneering, self-employed attitude. The small size of the operations is reflected in low productivity, a tendency to repair and rebuild equipment rather than replace it, designed flexibility in the processing plant, minimal reserves investigation or development planning and a versatile and innovative work force who are generally not professionally trained. The Resource Management Act and the Health, Safety and Employment Act as well as a customer driven demand for higher quality and consistent products will have even greater influence upon future direction of the Industry. The trend will be towards fewer quarries operated by companies and professional managers that can adapt to the new demands.

Jan 1, 1993

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By J. W. Evans

Mathematical modeling has now become a standard technique in the development of new technology and the improvement of existing technology in the processing industries. Physical modeling has a longer history but a smaller following at present. The paper reviews some examples of the application of both types of modeling in non-ferrous metal extraction, particularly within the copper and aluminum industries. The objective is to show that well founded models can lead to results that have practical consequence in scaleup, design and operation.

Jan 1, 1993

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993

By R. A. Haney

The Mine Safety and Health Administration (MSHA) has conducted studies both in coal and non-coal mines to evaluate methods for sampling diesel particulates in underground mines. The agency is investigating size separation techniques to distinguish between diesel particulate and respirable coal mine dust. Additionally, ashing techniques have been used to distinguish diesel particulate from mineral dust in metal and non-metal mines. As part of these studies, personal exposures to diesel particulate for various mining occupations have been measured. This paper describes the measurement techniques and summarizes the exposure levels for various underground mining operations.

Jan 1, 1993

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By Maleki. Hamid

The U.S. Bureau of Mines implemented an inte¬grated static and geophysical monitoring program in a southern Wyoming mine to study changes in seismic wave propagation properties in roof strata. The purpose was to develop techniques to assess roof stability problems. The work consisted of record¬ing deformation and stress histories and calcu¬lating seismic velocity profiles. In addition. geology and roof conditions were mapped; the in¬struments were initially installed at the develop¬ment face; monitoring continued until the mecha¬nized retreat face retreated within 60 m of the instruments. Mining geometry consisted of a three-¬entry gate system using 5.2-m-wide pillars at depths of 426 m. Results were analyzed using stan¬dard history plots, velocity tomographs, and numer¬ical modeling techniques. Changes in velocity. frequency, amplitude, dynamic elastic modulus, and dynamic Poisson's ratio were related to roof defor¬mation, fracturing, and support requirements. A reduction in seismic velocity of 17 pct occurred after 60 mm of roof deformation following installa¬tion of supplementary support. Static measurements revealed significant dilation in the mine floor, spreading to the pillar and the mine roof. Failure was initiated in the floor as a result of uniform pillar penetration.

Jan 1, 1993