Search Documents

By Stewart R

Potential acid rock drainage from the destruction of metalliferous sulph-ides is recognised as a critical factor in the design and economics of any mining venture. While this realisation is relatively new, mining companies have embraced the issue with the aim of scientifically quantifying the magnit-ude of the problem, specific to indiv-idual properties.Coinciding with the development of the open pit mine at Porgera, a comprehensive assessment of the potent-ial for the formation of acid rock drainage was initiated in 1991. Detail-ed study of the mineralogical charact-eristics of all rock types, along with extensive test work to determine the maximum potential of rocks to generate and consume acid (known as acid base accounting or ABA), has been conducted. Correlating this with the known and interpreted geology of the open pit has indicated a strong relationship between rock type, sulphur content and the acid base character. This relationship is used daily as a simple, cost effective means for classification and management of the variety of material types produced from the minincx operation.

Jan 1, 1994

By J. C. Taylor, J. A. Davis

"Existing environmental, health and safety regulations have forced pyrometallurgical facilities worldwide to drastically change some of their traditional methods of operation. In extreme cases, a number of facilities have been closed due to their inability to conform to these existing regulations. Tougher future legislation and government policy will lead to more stringent regulations and enforcement policies. The efficient control of smelter secondary emissions will, therefore, become critical to successful smelter operation.Much attention has been paid to the smelter primary process off-gas systems, including the development of new process designs to reduce the number of uncontrolled transfer operations. However, even the most modem smelter design requires control of its secondary contaminant sources, which mayor may not be directly related to the process operation.This paper discusses some of the potential secondary emissions encountered in many of the present process technologies. A few of the emission sources presented are only periodic in nature, such as those caused by maintenance procedures, but which have the capability of forcing smelter shut-down because of their direct impact on worker health and safety. The paper deals with a variety of topics relating to the efficient control, maintenance and monitoring of secondary emissions in copper, nickel, aluminum, magnesium and lead smelters, as well as in iron foundries and steel making facilities. Examples of the typical problems encountered in each of the above process operations are presented, including fume control at furnace tapping and slagging locations, metal transfer stations, tapping launders, and ladle transfer operations. The parameters for the most efficient design of fume capture systems, problems encountered with the handling and clean-up of certain collected emissions, and examples of successful solutions in particular operations are discussed."

Jan 1, 1994

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Gary A. Perry

Cyprus Sierrita produces copper and molybdenum from its Sierrita and Twin Buttes open pit mines south of Tucson, AZ. Both pits were started in the late 1960s and are more than 460 m (1500 ft) deep. Sierrita has used a Caterpillar 992C Remote Controlled Loader since January 1993. The loader was justified to increase safety and profits at Sierrita. It has exceeded all expectations. As of June 1993, the 992C had produced additional profits of more than $1.5 million. Safety and Geotechnical The safety of Cyprus personnel and equipment is always of prime concern. The remote controlled loader removes personnel from the active raveling area. But it requires prudent operation. The remote controlled loader discussed here is always intended to be used in a safe manner under a managed slope. Any increase in slope angle or use of any equipment under a critical slope is taken only after careful analysis of the specific

Jan 1, 1994

ARTICLE I - General Section 1. Name. The name of the corporation shall be The Rocky Mountain Coal Mining Institute. Section 2. Objects and Purposes. The objects and purposes of The Rocky Mountain Coal Mining Institute and the nature of the business to be carried on by it are as follows: (a) To sponsor educational programs pertaining to coal mining technologies and production techniques, mining management and safety, federal, state, and local laws, rules and regulations pertaining to coal mining, and other energy related issues. (b) To disseminate to the public and to educational and scientific institutions knowledge, and the results of study and research into recent developments in coal mining technologies and production techniques, mining management and safety, federal, state, and local laws, rules, and regulations pertaining to coal mining, and other energy related issues. (c) To do and engage in all lawful activities that further or are consistent with the preceding objects and purposes of the corporation. Section 3. Nonprofit Corporation. This corporation shall operate as a nonprofit corporation under the laws of the State of Colorado. ARTICLE 11- Principal Office and Corporate Seal Section. 1. Principal Office. The principal office and place of business of the corporation in the State of Colorado shall be in the County of Jefferson, Colorado, or at such other location as the Board of Directors may from time to time determine. Other offices and places of business may be established from time to time by resolution of the Board of Directors. Section 2. Corporate Seal. The seal of the corporation shall be inscribed with the name of the corporation, the year of its incorporation, and the words "Colorado" and "Seal," and shall be in a form approved by the Board of Directors, which may alter the same at pleasure. ARTICLE III - Members Section 1. Classes. The membership of the corporation shall be divided into three classes, consisting of active members, life members, and senior members, who shall have such rights, privileges, and qualifications as these bylaws may provide. Section 2. Qualifications. The members of the corporation shall have the following qualifications: (a) Any individual interested in the goals and purposes of the corporation may become an active member of the corporation upon payment of such annual dues as the Board of Directors may determine from time to time by resolution. (b) An individual who has devoted long and dedicated service to the corporation and to its goals and purposes may become a life member of the corporation upon being elected to that status by the Board of Directors, and such individual shall retain such status for life. (c) An individual who has been at any time an active member of the corporation and who has reached 70 years of age may become a senior member upon payment of such annual dues as the Board of

Jan 1, 1994

By Patrick J. Coughlin

Shortly after Asarco Inc. purchased the Ray Mines Division from Kennecott in 1986, the company began an expansion program to increase copper production. The Bechtel Corp. oversaw engineering procurement and construction management for a new in-pit crusher, overland conveyor system and concentrator facility. Construction started in May 1990 on these facets of the expansion project. The concentrator was commissioned in February 1992. The Ray concentrator uses a single-line, semiautogenous grinding circuit (SAG) with a design through¬put of 27 kt/d (30,000 stpd). In the early 1960s, Kennecott conducted pilot plant grind tests of Ray mine ores to determine their amenability to SAG and autogenous grinding methods. Those tests, though, were not followed up. During 1973 and 1982, Kennecott conducted additional pilot testing on some of the softer ore types. In 1989, Asarco ran a final series of SAG pilot grinding tests at Lakefield Research, which became the basis of the new Ray concentrator grinding circuit. Even though pilot test work demonstrated that some of the Ray ores gave satisfactory results during the autogenous grinding tests, the SAG option was selected for the primary comminution device. Due to the wide range of mineralogies encountered in the Ray ore body, selective mining and blending of these ores would be required to achieve the necessary production efficiencies and throughput rates using an autogenous grinding circuit.

Jan 1, 1994

Carbonatites - igneous carbonate-silicate rocks - host the world's major resources for niobium, phosphorous and REE (rare earth elements).Carbonatites represent the least common products of mantle and igneous processes and their emplacement is principally controlled by lithospheric domes and rift structures. Intrusive carbonatites frequently comprise carbonate-amphibole-apatite-pyrocWore assemblages, occur as plugs, cores, dykes, sills sheets, veins, pipes and irregular bodies, are gecichemically anomalous (Ba, Ca, Cl, F, Hf, Mg, Nb, P, REE, S, Sc, SO4, Sri Tb, Ti, D, V, Zr), are associated with alkaline silica-undersaturated igneous rocks forming carbonatite complexes, and display large, intensive alteration haloes. Also carbonatites are similar to limestones, prone to weathering, and may form thick laterite profiles.Magmatic ores (pyrocWore, apatite, bastnaesite, monazite, magnetite, baddeleyite, phlogopite, fluorite, calcite) and weathering related residual and supergene ores (pyrochlore, apatite, magnetite, anatase, vermiculite) are currently being mined on all continents except Australia. Australia is underexplored for carbonatite associated primary magmatic and especially residual-supergene ore deposits. Chances are very high for the finding of new carbonatite, occurrences and associated ores.

Jan 1, 1994

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By D. Eyde

The zeolites review arrived too late for the June issue. The natural zeolite industry continues to grow even as some companies look for the exits. Production for 1993 was estimated at between 42 and 44 kt (46,000 and 48,000 st). That is between 7 and 9 kt (7700 and 9900 st) above 1992 production. GSA Resources, Saint Cloud Mining, Steelhead Specialty Minerals, Teague Minerals, UOP and Zeotech all reported continued growth last year. At the same time the East-West Minerals' Eastgate mordenite mine, and American Resources' Ash Meadows clinoptilolite operations both shut down their processing plants and are attempting to sell the mines and facilities. In addition, Tenneco Minerals continued its attempt to sell the Mud Hills clinoptilolite deposit. Unimin entered the natural zeolite industry through its acquisition of several properties of Aimcor. The properties included the Ben-Jel bentonite and Castle Creek clinoptilolite deposits and processing facilities near Caldwell, ID

Jan 1, 1994

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994

By C. Stapel, AA Groningen, R. J. De Meijer

"In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

In the past five years, there has been an evolution in the assessment and control of mining risks in the New South Wales coal mining industry. This change has involved the development and use of structured, systematic, team-based risk assessment exercises to identify, assess and control unacceptable risks to people, equipment and production. The outcomes have improved the management systems in the mine. This paper discusses the evolution of the risk assessment approach in equipment design and mine operations, as well as the specific risk assessment methodology. The paper also presents the reactive side of risk management, the method of investigating failures in the management system, usually referred to as incidents or accidents.

Jan 1, 1994

By Derek J. Fray

Electric arc furnace dusts, especially those containing zinc ferrite, are notoriously difficult to process to give valuable products and non-toxic residues. The ideal process would remove and recover the toxic non-ferrous metals as pure metals, of commercial value, and non-toxic residue which can be used as a raw material in the steel industry. From an examination of the thermodynamics of the oxides and chlorides of the various elements in the dust, it is apparent that the chlorides of the toxic non-ferrous elements are more stable than the oxides while the reverse applies to the ferrous elements. This offers the opportunity for a complete separation of the zinc, lead and cadmium from the iron oxide. Results are presented for the chlorination of electric arc furnace dusts under oxidising conditions and the subsequent treatment of the chlorides to recover the pure metals and chlorine which can be recycled back to the reactor.

Jan 1, 1994

By Peter W. Harben

Once considered the dowdy country cousins of the glamorous metallics, industrial minerals are shedding their old image. They are neither common nor easy and their time has come in an age of increasing specialization. Consider that of the 45 or so industrial minerals and rocks listed in [Table 1], almost three-quarters have ten or fewer significant suppliers (i.e., those individual countries contributing 2% or more of total world production); in more than half the cases, 85% of world production is accounted for by only five countries or fewer. Curiously, even materials that appear to be virtually ubiquitous like crushed rock and common salt have significant production vacuums. For example, there is a severe lack of sound aggregates along the US Gulf Coast and common salt production on a large scale is virtually absent in central Africa. These examples all underline the obvious, but acute truism that "The single most important fact about mineral resources is that they are not distributed equally over the world" (Flawn, 1966). Just as significant today is that human resources are not distributed equally over the world, and so arise some interesting commercial incongruities. In certain regions raw materials are plentiful but consumers are not, and without a market a mineral deposit is merely a geological curiosity. Elsewhere, there may be a market but no local raw material supply. For example, despite a huge market there is no or virtually no commercial production of chromite, diamonds, and manganese in the United States and Canada, nor phosphate rock, diamonds, rutile, and zirconium minerals in western Europe. In contrast, Australia with its small domestic market is the world's largest supplier of bauxite, diamonds, ilmenite, natural and synthetic rutile, and zircon; the same is true for South Africa which is a leading producer of chromite, manganese, diamonds, andalusite, ilmenite, rutile, and zircon (Table 2). In the commercial world, Nature's uneven distribution is counterbalanced by deep sea international trade.

Jan 1, 1994

By T. T. Natarajan, Nagy EI-Kaddah

"Numerical simulation of electromagnetic confinement systems generally requires large CPU time due to the strong coupling between the electromagnetic and the free boundary problems. The present paper examines the accuracy and the computational efficiency of the most common numerical schemes used in modeling such systems. Levitation melting was taken as a test case. In this study, a comparison was made between the finite element and surface integral methods for electromagnetic field calculations. The computational efficiency of Lagrange and the modified Hestenes methods for solving the free boundary problem were investigated. The convergence of the Lagrange method was found to be much faster than the modified Hestenes method. It was also found that finite element method not only gives accurate solutions, but faster convergence to the final equilibrium shape than the surface integral method. The applications and the limitations of these techniques in modeling electromagnetic confinement systems will be discussed.IntroductionIn recent years there has been a growing interest in the use of electromagnetic forces for confinement of molten metals as a means to eliminate molten metal contamination during melting and to improve surface quality of cast products. Continuous casting of metal without contact of a mold is now a reality, and is being commercially applied for casting of aluminum slabs /1/, and copper rods /2/. New applications of electromagnetic confinement in melting and casting include containerless melting (Magnetic Suspension Melting) /3/, edge containment in twin roll casting, and meniscus shape control in continuous casting of steel /4/.Modeling of confinement systems involves the determination of the electromagnetic field and the equilibrium shape. These two problems are strongly coupled due to the dependence of the field on the shape of the melt. While significant advances have been made in computational electromagnetics /5/, the application of developed computational techniques to electromagnetic confinement problems is not a simple task. The principal difficulty in using these methods is that the solution domain is not known a priori. due to coupling between the electromagnetic field and the free boundary problems. These two problems have to be solved simultaneously, leading to an iterative solution procedure. As a result, numerical simulation of electromagnetic confinement systems are computationally intensive with computational time at least an order of magnitude larger than the fixed domain problems."

Jan 1, 1994