Search Documents

By E. Fregeau-Wu

The major obstacle in recycling steelmaking slags to the blast furnace is their phosphorus content. Removal of the phosphorus, which is primarily associated with the silicate and phosphate phases, would allow for greater recycle of these slags for their iron, manganese, and lime contents. Calculations show that separation of the silicates from the oxide phases would remove nearly 90% of the phosphorus from the slag. The variable grain size of the as-received slag made liberation by fine grinding difficult. Therefore, slow-cooling experiments were undertaken to improve the grain size distribution. The grain size distributions were determined using in-situ image analysis. The samples were ground to their apparent liberation size and high gradient magnetic separation was used to separate the magnetic oxides from the nonmagnetic silicates and phosphates. Liberation analysis and modeling was performed on selected separation products for discussion of benefication characteristics.

Jan 1, 1995

By S. W. Beckman, L. Williams, A. E. Seep, R. Fischer, J. Hubbard

Introduction The Summitville Mine located in southwestern Colorado was added to the National Priorities List in June of 1994. Summitville was the site of mining operations that began in 1873 with the discovery and development of gold placer and lode deposits in the late 1800's. The mine site is located about 25 miles south of Del Norte, Colorado in the San Juan Mountains adjacent to the Rio Grande National Forest at an approximate altitude of 11,600 feet. The site was mined for gold, silver and copper between 1873 and 1947. The Summitville Consolidated Mining Corporation, Inc. (SCMCI), a wholly-owned subsidiary of Galactic Resources, Ltd of Vancouver, Canada ran a large tonnage open-pit mine and cyanide heap leach operation from 1986 to 1992 (Pendleton and Posey, 1992) During the mine operation by SCMCI, approximately 10 million tons of gold ore was mined, crushed and stacked on a lined leach pad. Heap leach operations experienced water balance and unplanned solution discharges from the start of the mine life. Despite the production of 249,000 troy ounces of gold during the mine operation, SCMCI was unable to meet remedial requirements and notified the state of Colorado of its intention to file a Chapter VII bankruptcy in December 1992. The EPA Region VIII Emergency Response Branch took over site operations on December 16, 1992 to prevent a catastrophic release of hazardous substances to the environment. The multiple contamination sources at the mine site are due to both historic and SCMCI mining operations. Emergency response operations at the site have prevented releases of severely contaminated solution and a permanent treatment for all waste units at the site is under investigation. A Request for Proposal (RFP) was issued in October 1993 by Environmental Chemical Corporation (ECC) at the Request of EPA Region VIII, Department of the Interior and Bureau of Reclamation. The RFP requested that interested companies provide information on their ability to implement innovative treatment technologies to improve treatment efficiency and reduce treatment costs for remediation of the heap leach pad (HLP) spent ore and ore leachate solutions. Dames & Moore and Pintail Systems, Inc. (PSI) jointly submitted a proposal suggesting application of biotreatment processes for detoxification of cyanide in spent ore and HLP leachate solutions. The proposal was accepted for pilot and field demonstration under the SPA Superfund Innovative Technology Demonstration Program (SITE) with additional funding from EPA Region VIII. This report discusses the test program and results of a Focused Feasibility Study which demonstrated biotreatment processes for spent ore cyanide detoxification.

Jan 1, 1995

The response was good-one of the best the SAIMM has had to its various questionnaires. 231 replies were received from 2768 members representing a response of 8,35%. For fellows and Members together, the response was 13,7%. The spread of responses based on respondents' work situation appeared to be well balanced with some bias from those in consulting organizations. Members' perceptions of their employers' positions withrespect to environmental management looked somewhat optimistic, but it is encouraging to note that they reported that more than half were developing environmental management systems. Training of varying degree was taking place at al levels in their organizations. Members saw their Institute as an important agent inlifting environmental awareness, literacy and responsibility not only through the journal and symposia, but also by liaison with government departments and educational institutions. Most respondents saw environmental legislation both from local and overseas sources as affecting their organizations, their products and services with the emphasis on corporate image, core business and sales.

Jan 1, 1995

By Clarici E, Marsden J. R, Calderbank P. A

Evaluation of previous studies of multi-layer perceptron type artificial neural networks in the modelling of the deformability behaviour of rock have suggested that a deviation from the standard method of laboratory testing of rock under triaxial loading at constant confining stresses and constant axial strain rates may be inappropriate when the data produced are used to train an artificial neural network. In this paper, preliminary results of adopting such a strategy are reported. Of specific concern is the establishment of a suitable schedule for the stress path during testing. Furthermore, the training element of back propagation optimisation was directed towards prediction of new stresses given old stresses and old strain increments. Adoption of this method of supervisation in artificial neural network training facilitates the integration of the trained neural network within existing numerical methods used in rock mechanics. The target code was a finite difference Lagrangian formulation for the analysis of continua. Sandstone rock taken from a quarry in the UK was used in the study which showed that the method has great potential.

Jan 1, 1995

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By Sadan Kelebek, S. O. Fekete, Gerhard W. Heinrich, Peter F. Wells

"For many years, rejection of pyrrhotite at the milling stage has been a viable method for sulphur dioxide abatement. Pyrrhotite rejection options have included the use of selective pyrrhotite depressants in flotation; a depressant which has recently come into use is diethylenetriamine (DETA). This reagent has been the subject of recent research and development efforts in the processing of nickel-copper sulphide ores.In the present study, adsorption trends for DETA have been monitored under the dynamic conditions of flotation using a spectrophotometric method which has been adopted for this purpose at Falconbridge Limited. The results indicate that the adsorption of DETA is quite fast and in the majority of cases, accounts for the disappearance of 75-95 % of this reagent from pulp's liquid phase. The adsorption decreases linearly with an increase in the DET A dosage from 100 git to 600 git. The tailings produced in flotation tests were subjected to washing with deionized water at 60 °C to examine the desorption of DET A. These results indicate that the amount desorbed increases with increasing DETA dosage used during flotation but is less than 7 per cent of that adsorbed. It was found that adsorption of DETA alone, even at relatively high levels, does not always cause depression of pyrrhotite. A new combination of reagents identified in the metallurgical laboratories of Falconbridge Limited utilizes sulphur dioxide with DETA. These reagents together are capable of efficient depression of pyrrhotite on a consistent basis."

Jan 1, 1995

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

By W. Kennedy Gauger, Tim Oolman, Debra L. Bisson

Radian Corporation (Radian) has developed a process for treating Cr(V1)-contaminated soils that involves: 1) soil washing using an alkaline extractant, 2) biological reduction of Cr(V1) to Cr(II1) in the soil wash effluent, and 3) separation of Cr(II1) from the biologically treated effluent. Biological treatment has been demonstrated for immobilized cells in fluidized bed bioreactors and suspended cells in slurry bioreactors for Cr(V1) levels ranging from 30 to 600 mg/L which have been reduced to non-detectable levels (< 0.05 mg/L; method detection limit [MDL]) during hydraulic residence times as short as 12 hours. The resulting Cr(II1)-containing effluent stream was chemically treated to precipitate chromium hydroxide for removal by physical separation.

Jan 1, 1995

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By Mao Bai

Mining in situations where there exists a potential hazard from inundation has always existed in coal mining, and often reserves were left unmined in favor of reserves with no such hazard. However, increased pressure on expanding the minable reserves and on producing low-sulfur coal, has made mining under water hazards necessary in many parts of the world. Recent joint efforts by the authors to develop case-history data bases of mining under water hazards has allowed the bringing together of Chinese and United States experience and guidelines for such mining. In China, mining under water hazards has been successfully accomplished for a number of years, allowing the development of a good data base from which to draw guidelines. In the United States, much more limited experience, and the longer delay in adopting longwall mining compared to the rest of the world, has forced reliance on a more limited data base and European experience. In the United States (and Canada), the data base is continuing to increase as more operations start-up. Developing a generally-applicable set of guidelines for international use, based upon extensive Chinese and other experience, appears feasible. The Chinese and United States experiences are detailed by case histories.

Jan 1, 1995

By Zhang Zhitie

The limitations in mechanism research of mineral comminution in the past and the basic features of the comminution process have been analyzed. Two kinds of catastrophe model, i.e., cusp model and swallowtail one in the mineral comminution have been put forward. The dissipative structure of the mineral comminution: entropy production rate, extra entropy, extra entropy production and system stability has been discussed. The physical nature of the behavior that an old structure was destroyed and a new one was produced in the mineral comminution process has been brought to light.

Jan 1, 1995

By Sengstock G. W, Spathis A. T

Benchmarks of mine equipment involved in the excavation process of coal mines would suggest that such equipment is not always operating at an optimum level. Dragline operations and truck/shovel operations rely on efficient use of their plant in order to maintain high mine throughput. The first process which affects the material to be excavated is the drilling and blasting process. Drilling and blasting delivers a fragmented material with a given disposition ready for excavation by mine equipment. As mine operators demand more productivity from their major excavating equipment, many sites are considering the use of productivity monitors to measure their outputs. Some of these productivity improvements will be directly related to the drilling and blasting process, so that as the monitoring systems improve, the opportunities to evaluate all drilling and blasting variables will also improve. This paper reviews current and newer methods for monitoring equipment productivity in mines. These include simple time and motion studies obtained by either manual timing of processes or by automated data collection equipment being adopted by the industry. Case studies for truck/shovel operations are discussed and the productivity improvements are compared with typical industry standards. These improvements relate specifically to parts of the load, haul and dump cycle and the potential for significant improvements are identified. Particular opportunities for drilling and blasting improvements are also presented.

Jan 1, 1995

By A. M. Al Taweel, S. M. El Mofty, T. A. Hassan, M. R. Moharam, A. M. Ramadan

The axial mixing characteristics of a pilot-scale flotation column were investigated with the objective of identifying means to mitigate the extent of axial mixing that adversely affects its grade/recovery performance. A wide range of design and operating conditions was investigated and the experimental results, obtained using the dynamic response method, were analyzed using three axial mixing models. The dynamic response of the column can best be described using the axial dispersion model. The results obtained suggest that the value of the axial dispersion coefficient, EL. can be signi6cantly reduced by judicial selection of hydrodynamic conditions and/or the use of column inserts that suppress the onset of hydrodynamic instabilities inherent to the operation of conventional flotation columns. Up to 40% reduction in the value of EL was thus obtained by using spargers that produce more uniform bubble sizes, while up to 30% reductions were obtained by controlling the residual frother concentration.

Jan 1, 1995

By Randall C

Energy studies have been undertaken at a number of open coal mines in the Hunter valley. A range of energy efficiency benchmarks and targets have been established, which, when applied across coal mines, will assist in leading to a significant improvement in energy efficiency in the coal mining industry in NSW, thereby leading to an improvement in environmental performance. Typically, energy efficiency improvements of 20 per cent and higher appear possible at many mines leading to a commensurate reduction in this controllable operating cost, ie energy. On the basis that annual energy costs and net profit are similar for many mines, a reduction in energy costs by 20 per cent will lead to increase of 20 per cent in net profit.

Jan 1, 1995

The 98th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 1995. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows R.C.J. Goode, F.G. Hill Life Fellows R.S. Cooke, J. W. V. Mortleman Fellows S. Craib, R.R. Hendry, T.J.B. Jones

Jan 1, 1995

By Kotaro Ohga, Kiyoshi Higuchi

In our laboratory, a new detection system using smell detectors was developed to detect the spontaneous combustion of coal and the combustion of other materials used underground. Laboratory experiments were carried out on several kinds of coals, including South African coals, and machine oil, wood and rubber used in belt conveyers. The following results were obtained: 1) Spontaneous combustion of coal can be detected earlier by smell detectors than by conventional CO detection methods. 2) There were no differences in the results using different kinds of coal. 3) Combustion of other materials can also be detected earlier by this system than by conventional detectors for gas and smoke. 4) Use of this detection system enables one to discern the source of the combustion gases, whether it be coal, wood, oil or rubber.

Jan 1, 1995

By Peirong C, Pei N, Shouxi H, Hongzhong X

Indosinian (T) orogeny amalgamated the Mongolia-Xingan fold zone, the North China continent, the Yangtzi platform and the SE China fold zone into a unified continent. The early to middle Yanshanian (J-K,) orogeny created a Cordilleran type active continental margin in East Asia, reactivated the consolidated East China continent, and generated a large amount of granitoids, calc-alkaline volcanics and W, Sn, Mo, Cu, Au, and U ore deposits. The late Yanshanian (K2) orogeny began a transition to the western Pacific type continental margin. A tensional environment led to the development of peralkaline magmatism and the formation of continental basins with red beds. The Himalayan (Tr-Q) orogeny was characterised by a backarc spreading and rifting regime. The dominant magmatism was continental basaltic.

Jan 1, 1995