Search Documents

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

Mintek now offers a service for the accurate measurement and analysis of air pollution in South Africa. 'The deteriorating air quality and general degradation of the environments in industrialized and urban regions of South Africa have been of concern for more than a decade', says Mintek's Dr Johann Engelbrecht. 'The accompanying effect on health, visibility, and damage to property and the environment have prompted the public, authorities, and industry to take appropriate action. A recent study conducted by the Medical Research Council on schoolchildren in the Vaal Triangle, clearly demonstrated the relationship between the deficient quality of the air in that area, and the resultant respiratory diseases.

Jan 1, 1996

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high-expansion foam generator. Thus allows fire fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600 ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Jan 1, 1996

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By Uwe Hess

For the Danish landworks for the coming fixed link between Denmark and Sweden across the Øresund the focus has been on the environmental aspects of the construction and operation of the facilities. This paper describes how the environmental objectives pertaining to the project have influenced the design and construction of one of the major elements of the Danish landworks, i.e. the tunnel in Sydhavnsgade and under Sydhavn Station. The chosen construction methods for the construction pit bracing and the groundwater lowering will be described along with the observed effects on the environment as shown by simulated or measured values for noise impact, settlements, pumped groundwater and extension of the drawdown cone.

Jan 1, 1996

By John A. Herbst, William T. Pate

"Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen, and the coordination of all unit operations in pursuit of the highest performance level. However, several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of unit operations to account for critical interactions within and between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significaritly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated with the models and can be effectively optimized. Financial goals seems to be the objectives of choice.This paper discusses recent progress in overcoming the challenges and illustrates a promising approach which is being pursued at Mexicana de Cobre's La Caridad copper ore concentrator. At M de C, advanced control strategies have been installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, increased from 76,000 tpd to 90,000 tpd. Plantwide integration is expected to gain an additional 3% improvement in profitability."

Jan 1, 1996

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Jan Tegtmeier, Horst Gerhardt

INTRODUCTION Under certain circumstances the closure of former mines which are located above a certain flood level can result in problems such as the emanation of detrimental substances after having completed filling and reclamation operations. This especially applies to uranium mines in which the radiation dose could far exceed the dose of natural background radiation. By means of an example of the uranium mining in Germany in the following it will be demonstrated how to cope with this problem. On the basis of comparative investigations in various vein deposits and using ventilation scheme calculations proposals for the optimization of the necessary forced ventilation can be submitted. REPORT ON SITUATION In the period 1946 - 1989 the former Soviet-German joint- stock company "Wismut" developed into the biggest European uranium producer with a total output of about 220.000 t of uranium. A major mineraldeposit district was the deposit of Schlemaf Alberoda in the Saxon Ore Mountains, in which 80.000 t of uranium were produced. Thus it is among the biggest uranium de- posits of the world, from which various other metals were at- tracted for many centuries. The exploitation of the Schlemal Alberoda deposit involved steep veins in regions near the surface as well as depths of 1.800 m. Until 1991 a total excavation space of 40 million m3, which is flooded at present, was produced. With the average increase in the water level of 80 cm per week the final flood level is expected to be reached in the year 2003. The shaft 373 at present still being used for ventilation will be no longer available since the second quarter of 1998 after flooding the -540 m level because it is not connected with the excavation system near the surface. As a study shows, a radiation dose far above the natural back- ground radiation has to be expected for the town of Schlema due to the extensive mining activities near the surface and due to the subsequent displacement with missing depression fo the main mine ventilating fan. An uncontrolled air flow containing radon leaves the open mine excavation due to the effect of the natural ventilating pressure and emanation caused by the barometric pressure drop with atmospheric pressure fluctuations. This mine air with its high-level radioactive equilibrium results in a high radiation dose in buildings (see Figure l). After having switched off the main ventilating fan in order to investigate the effect of the missing depression the increase in radon concentrations amounted up to 700% in various buildings of Schlema. This was partially due to the inversion state of the weather at that time. The high radon concentration has detrimental effects on the health of the population and of the miners working on the further reclamation in regions above the flood level. ANALYSIS OF THE RADON EMANATION RATE EXPECTED Considering the composition of the radon inflow from the mine workings it becomes evident that 80 % of the radon inflow originates from abandoned excavations and only 20 %from open ventilated mine excavations. This fact has to be taken into account for the ventilation after having reached the final state of flooding. After completing ventilation the radiation dose on the surface is mainly due to the radon emanation from excavations close to the surface. Investigations of the Wismut GmbH showed the in- crease in the specific radon emanation rate by a factor of 100 for abandoned excavations as compared to new drivings. One reason is the larger specific surface of abandoned galleries caused by displacements due to mining activities as well as by fall of hanging. Furthermore the radon can enter the gallery through joints, which have subsequently opened by convergences. All these effects result in a larger free surface available for radon diffusion. The large number of drivings in the deposit sections near the surface and the fact that the highest uranium contents are found near the surface as well as the high fracturing are further reasons for higher emanation rates. Considering these facts it can be expected that the radon inflow of 10.000 kBq/s, which refers to an open mine excavation of about 1.4 million m3, represents a minimum. Only by increasing the specific surface, for which a numerical value has still to be determined, this value will increase with certainty. An extensive radon emanation from the residual excavation, which cannot be flooded, can only be prevented by maintaining the ventilation system. The low pressure produced by the fan in the mine openings prevents the emanation of air containing radon due to the effect of the natural ventilating pressure. Without the controlled withdrawal of the radon the population as well as the miners working on the further reclamation in areas above the flood level would be endangered. Therefore the follow-

Jan 1, 1996

By S. A. Pirzada

A thermal plasma assisted laminar flow reactor has been used to evaluate the kinetics of converting alumina to sodium aluminate in flight. Free energy minimization calculations were used to determine experimental conditions. The experimental variables include: alumina particle size, alumina/sodium nitrate molar ratio, temperature and residence time. A mathematical model for the conversion was developed and validated. Experimental and mathematical results are presented.

Jan 1, 1996

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By A. Andreas Hejja

Flow of slag and settling of matte in slag resistance electric furnaces are discussed in conjunction with furnace geometries, stirring action of the electrodes, buoyancy and electromagnetic effects. The rectangular electric furnace was regarded as a channel reactor and the mode of slag flow as a channel flow. The flow is affected both by buoyancy and electromagnetic forces, however the effect of electromagnetic forces is minimal. The flow velocity is made up of two components; (i) that developed by the action of the electrodes, and (ii) the bulk flow velocity determined by the smelting rate and the volume of the reactor. Slag samples were taken from various depths of the molten bath and were analyzed microscopically to determine the size and distribution of matte particles, The action of the electrodes was described by a simple mathematical formula indicating a balanced settling rate in the area of electrode action.

Jan 1, 1996

By A. M. Marabini, V. Alesse, Belardi. G.

An alternative flowsheet was designed for the flotation treatment of a complex sulfide ore from the Sotiel Mine in Spain. The ore contains 0.71% Cu, 2.24% Pb and 5.63% Zn. Two specially developed synthetic collectors, methyl-mercapto-benzoxazole (MMBO) and 6n-propoxy-mercapto-benzo-thiazole (PMBT), were examined. MMBO exerts a specific action on copper and zinc minerals after treatment with copper sulfate, and PMBT exerts a specific action on Pb minerals. Flotation operating variables (pH, frother type, frother quantity and feed particle size) were examined by means of rougher flotation tests to determine the optimum conditions for the new collectors. Once the optimum conditions were determined, a series of open flotation circuits were run on feeds of various particle sizes (obtained by different types of grinding). The objective was to obtain high-grade Cu and Zn concentrates. The results of the open-circuit tests demonstrated that a Cu concentrate grading from 18% to 23% Cu and a Zn concentrate grading from 40% to 48% Zn can be produced.

Jan 1, 1996

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By D. McConchie

Management of caustic red mud wastes at the QAL bauxite refinery uses an innovative approach . involving neutralising the red mud with seawater; solids settle in a Red Mud Dam and residual water (pH = 8.6) is discharged to a tidal inlet. A survey of 18 trace elements in sediment, water, mangroves and molluscs, and an ecological survey of benthic fauna in the inlet, and at near-pristine control sites, revealed no significant trends that were linked to the discharge, except for the concentration of Al which was slightly elevated within 100m of the outfall. Trace element concentrations in water samples were close to, or below, world average seawater values and oysters collected near the outfall were acceptable for human consumption. The impact of discharges is minimised by a high tidal range, >60% flushing of the inlet in each tidal cycle, and the very high trace element binding capacity of sediment in the dam (> 100meq/ 100g dry mud).

Jan 1, 1996

Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the interaction between the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussed on the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled.

Jan 1, 1996

By G. Van Weert

Oxygen transfer from dispersed air in agitated slurries represents an important unit operation in the minerals processing industry. Gold leaching, iron precipitation and especially bio-oxidation come readily to mind. However, little engineering information is available on the variations between impeller types on such O2 transfer. Engineering literature on the subject, i.e. information which relates slurry density and energy input to O2 transfer, is reviewed and compared to current experimental work. The latter was carried out with minus 50 micron sand/water slurries in a 64 I laboratory tank of standard proportions, equipped with a variable speed drive with torque meter. A standard Rushton turbine and a specifically sized A315 were compared. Results confirm an increasing impairment of O2 transfer with increasing slurry density for both impellers. The volumetric mass transfer coefficient, k,a, in a 10 vol. % slurry shows a decrease of 30% compared to the k,a in water. At 20 vol. % sand this decrease is near 50 %, depending somewhat on superficial gas velocities. Power efficiency, i.e. the kg O2/kWh, decreases about 25 % more rapidly for the Rushton turbine than for the A315 with the addition of sand. However, for equivalent O2 transfer the Rushton turbine was more efficient in this work. Experimental results are presented and their significance for slurry bio-oxidation discussed.

Jan 1, 1996

By Graham G. W. Mustoe, Andrew I. Hustrulid

An advanced numerical model based upon the Discrete Element Method (DEM) has been developed to provide the engineer with unique detailed information to assist in the design of transfer points in large industrial conveyor systems in mining operations. This modeling technique provides a quantitative description of the bulk solids movement through the transfer point. This information consists of the velocity distribution of the bulk solids and the stresses within the bulk solids. The DEM model also gives detailed information concerning the impact forces acting on the transfer structure and the conveyor belts from the bulk solids flow.

Jan 1, 1996

By Greg Barfoot, K. Payne

Condition monitoring of conveyor belting has become an established tool for maintenance programming, replacement strategies and quality assurance for belt conveyor systems. What is less well known is that the condition of the conveyor belting is usually a symptom of problems in other areas rather than the problem source. This paper presents an overview of the state of the art in belt monitoring and the move towards on-line NDT systems. The use of belt monitoring data as an indicator for overall system design, maintenance and operation is also discussed.

Jan 1, 1996

By Marina K. Peshkova, Izabell V. Pomorova

Computer modelling system for definition optimal way of in- vestment under condition of diverse directions of activities mining enterprises has been created. The main purpose of paper is to introduce the new scientific approach of finding effective variants of investment for mining industry under free market condition in Russia, it can be also interesting for domestic and foreign investors.

Jan 1, 1996