Search Documents

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By Harnish Miller, Scott G. Giltner

One of the concerns with locating radioactive waste storage sites in salt deposits is how to permanently seal the underground storage areas once they have reached their storage capacity. The compaction of salt using explosives has been identified as a potential method of producing permanent seals in both entryways and shafts to storage areas. This paper describes the test procedure and results of a preliminary investigation to determine the feasibility of utilizing explosives in the compaction of salt. Three simple tests were carried out to measure the degree to which loose salt could be compacted.

Jan 1, 1996

By E. Kaya

Investigations of fine grinding of bituminous coal in a laboratory-scale pulverizer are described. The results indicate essentially "normal" breakage behavior at relatively coarse sizes (greater than about 20 µm) but show clear evidence for re-agglomeration in the fine size range (less than about 10 µm). A simplified population balance model for simultaneous growth and breakage has been formulated. Breakage rates and breakage distributions are assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behavior. Agglomeration rates are assumed to be determined by contact probability, i.e. by the relative numbers of interacting particles. Based on comparisons of model simulations and experimental data, it appears that agglomerate re-breakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1996

By C. R. Edwards, D. G. Feasby

"Over the last 50 years disposal of uranium mill tailings has evolved from dumping untreated tailings into the nearest depression to depositing chemically-stabilized tailings into highly engineered management facilities. This paper describes the evolution of disposal methods and the criteria which have determined the development path followed. Remediation techniques to bring older and now unacceptable tailings deposits into satisfactory compliance with today's· regulations are reviewed.With the closure of the uranium mines in Elliot Lake, Ontario, considerable effort is being made on decommissioning the tailings areas by developing long term maintenance of water covers. The innovative methods being used to develop these water covers are detailed. Methods now under development in Saskatchewan for subaqueous deposition of high density or paste tailings for permanent disposal in mined out open pits are described.SummaryThe technology for uranium mill tailings disposal in Canada has evolved considerably over the past 51 years. This evolution has been driven by an improving understanding of how best to safely and permanently store tailings, in conjunction with stricter environmental protection regulations. Old sites are being decommissioned in situ, but may require long term care and maintenance. The use of water covers is an important technique in eastern Canada to prevent intrusion, radon evolution and, for the Elliot Lake tailings, acid generation. The major drawback of water covers in any above ground disposal method is the requirement that a long term maintenance and monitoring plan be put into effect for each site.New higher grade mines in Saskatchewan will increasingly use disposal in mined-out pits using the pervious surround method and/or paste tailings technology as a method to permanently dispose of these wastes and to permit “walkaway” after a few years of monitoring."

Jan 1, 1996

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

By J. Pérez

A lead smelter slag with high copper, lead, arsenic and silver contents was treated at laboratory scale for arsenic removal. The slag was first leached at atmospberic pressure with sulfuric acid and oxygen. According to arsenic contents leaching of most of the arsenic was achieved in either one or two stages, producing a lead-silver rich residue and a solution high in copper and arsenic concentrations. Alternative routes were considered to treat the resulting solution. Firstly, solvent extraction of arsenic with a mixture of TBP and 2-etbyl-bexanol was tested and extractions of over 95 percent of arsenic were achieved. Secondly, a copper arsenate precipitation treatment was done to eliminate arsenic and copper from solution.

Jan 1, 1996

By KNona C. Liddell

"Many metal recovery processes involve heterogeneous reactions in porous media accompanied by fluid flow and mass transfer. Modeling such systems is difficult because of the number of rate processes involved and is complicated even further by effects due to the structure of the porous medium. Data on even bulk properties of the medium are often severely limited or unavailable. For many such systems, a cell model may provide an attractive alternative to models based on transport mechanisms in a differential volume. A cell model requires less input data and is computationally efficient. Identical residence time distributions can be obtained with models of both types, and both allow conversion and concentration profiles and histories to be calculated. The formulation and properties of cell models for metals recovery are described in detail.INTRODUCTIONSubsurface mineral leaching, metal ion recovery and environmental remediation are significant modeling challenges. They involve one-, two-, or three-dimensional reactive flow in multi reaction open systems. Dissolution, adsorption, and ion exchange occur at reactive mineral surfaces, and these heterogeneous reactions are accompanied by acid-base, complexation, and redox reactions in the solution phase.Two approaches have been taken to reactive flow problems in geologic media: mixing cell and transport models. Mixing cell models, the subject of this review, are based on a network of connected cells, each with a specified number of input and output streams. Mixing cells are assumed to have no internal solute concentration gradients, that is, each cell behaves like a well-stirred tank. Gradients are represented by step changes between connected cells; this results in a model that is spatially discretized at the outset. Different methods of discretizing the model equations are considered more fully below. Although this is not strictly necessary, it has usually been assumed in subsurface flow applications that all cells in the network have the same volume and identical initial properties."

Jan 1, 1996

By J. D. McAteer

It is widely agreed throughout the mining community that federal mine safety and health legislation administered by the Mine Safety and Health Administration (MSHA) deserves significant credit for the past quarter-century's remarkable improvements in miner safety and health. Recently, however, it has been suggested that the mining industry in the United States has now evolved to a point that current mine safety and health law may be obsolete. This proposition deserves attention. Today, I propose to give it the close logical scrutiny that is its due. I conclude that the obsolescence of current mine safety and health law is not supported by the evidence. The existing mine safety and health law continues to serve as a critically important supplement to mine operators' safety programs at a modest cost to the taxpayer. At the same time, trends in a changing industry do call for responsive adaptations in the Federal mine safety and health program. I will argue that timely and appropriate responses to changing needs can be accomplished within the framework of existing legislation, provided federal officials avail themselves of the flexibility provided by existing law.

Jan 1, 1996

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996

By Rainer Schmid-Fetzer

"Isothermal solidification can be used to form strong bonds at low temperature which remain solid at much higher temperatures. The exploitation of this principally known technique for new high temperature processing steps and applications in electronic assemblies is the aim of this study. Three basically different variants of this bonding process are given. A comprehensive metallurgical screening is performed and the feasibility of binary material systems is given on a quantitative scale. Very attractive systems are spotted that have never been studied before. Detailed examples for the realization of bonding with complex ternary and multilayer systems are given. A highly innovative example is the chip stack or wafer to wafer bonding of unmetallized Si or SiC at 250°C. The proposed bond remains stable above the melting point of Si and enables entirely new semiconductor manufacturing steps. An improved die bonding process was proposed and verified experimentally.1. IntroductionIsothermal solidification can be applied to form strong bonds at relatively low temperature which remain solid at higher temperatures. The general principle of this type of joining processes is illustrated in Fig. 1. An interlayer of a low melting component, Lo, is provided as a foil or a thin film coating between the high melting joint components, Hi. The assembly is heated under moderate pressure to the bonding temperature, T 8 , and a liquid filler forms, either because the melting point of Lo is exceeded or due to a eutectic reaction between Lo and Hi. This molten filler initiates a rapid interdiffusion or reaction diffusion between Lo and Hi and the subsequent approach to an equilibrium state results in isothermal solidification. The solid phases formed at T 8 in the joint region exhibit a remelt temperature above T8 •"

Jan 1, 1996

By Peter K. Everett

One of the major driving forces behind the development of the Intec Copper Process has been the increasingly stringent regulations governing SO2 emissions and, in some parts of the world, a declining H2SO4 market. Other incentives include operating cost (9.2 US c/lb Cu), capital cost (US $1400/annual tonne Cu compared with smelter cost of US$3-4000/annual tonne Cu) and the ability to treat low grade and contaminated concentrates. With such advantageous features, widespread use of the process is expected over time, leading to the production of large amounts of residues containing around 25% elemental sulfur, together with approximately 50-60 % akaganeite (FeOOH) and the ganggue minerals originally present in the concentrate feed. This paper briefly describes the Intec process chemistry involved in the formation of elemental sulfur, thereby avoiding atmospheric sulfur dioxide pollution, and the investigations to be carried out either to extract it or to turn the residue into a valuable by-product while minimising any adverse environmental effects, The process is being developed jointly by a group of fifteen major international mining companies.

Jan 1, 1996

By T. T. Chen

Canadian Electrolytic Zinc has developed the "cement-stabilization of jarosite residue" Garofix) process to stabilize zinc plant jarosite residues for disposal. The cement-jarosite mixtures cure quickly, have good mechanical strength and low hydraulic permeability; they possess good neutralizing capability and chemical stability. In the jarofix process, Portland cement partly decomposes jarosite to form (SO4MOH)12.nH2O, ferric hydroxide and an alkali sulphate. Approximately 40% of the jarosite reacts in mixtures containing 30% cement. The jarofix product also contains various Ca-Al-Fesilicate-sulphate-hydrate phases and gypsum, which bond the individual particles together imparting mechanical strength and reducing the permeability. Most of the reactions take place in the first few hours of curing. Ammonium jarosite is slightly more reactive than sodium jarosite but releases NH3 gas; water-soluble Zn in the jarosite residue is stabilized in the cement reaction products.

Jan 1, 1996

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By William F. Loftus

When high capacity diameter pipe piles are driven open-ended into the underlying bedrock, the material gathered inside the pipe often must be excavated to allow concrete to be placed within, in a clean environment. This paper discusses a method of dealing with this ?to be excavated material - the contaminated soil of the Harlem River in New York City, USA.?

Jan 1, 1996

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By Randall M. Gennan

Generally sintering is focused on the bonding of particles at high temperatures; possibly with simultaneous densification. However, an important aspect of sintering occurs during heating at relatively low temperatures where polymer processing aids are removed via control of the atmosphere, heating rate, or hold time at intennediate temperatures. New insights into burnout processes show impact from the polymenype, particle size, amount of polymer, atmosphere, part geometry, and thermal profile. This presentation focuses on the key parameters to demonstrate improved mechanical property levels are available in traditional powder metallurgy alloys by proper selection of the processing polymer and proper care in its thermal extraction. The focus is on mechanical property, where gains up to 40% are demonstrated due 10 changes in the processing polymer. Further, atmosphere control during polymer burnout provides a benefit by allowing formation of desirable carbonitrides, giving strength levels over 3 GPa (over 400 kpsi). Insight is? gleaned from powder injection molding, where high polymer contents mandate proper processing control.

Jan 1, 1996

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By R. J. Dippenaar, W. H. Van Niekerk

"An injectable lime-based desulphurization reagent for the treatment of liquid iron was developed. Firstly, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na20 to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. Subsequently, pilot plant and full scale industrial injection trials were conducted. It was found that lime-based slags, containing Na20 and CaF2, are able to desulphurize liquid iron efficiently. By the injection of a lime based reagent consisting of 60% lime, 25% soda ash and 15% fluorspar at a rate of 7 kg reagent/ton hot metal, the sulphur level in the metal (115kg) was reduced from 0,07% to 0,01 % within 5 minutes. The lime-based reagent developed in this study was successfully injected, both from a metallurgical and from a pneumatic point of view, on an industrial scale. The mathematical model utilised in this study, can be used successfully to predict the course and extent of desulphurization by lime-based slags. IntroductionMainly due to environmental difficulties encountered with pure soda ash, dry slag formation with CaC2 and high cost when Mg are used as desulphurizers, much incentive exists for the development of an inexpensive, environmentally friendlier desulphurization reagent. As a first step in the development of such a reagent, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na2O to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. This was followed by pilot plant injection experiments in which the kinetics of the relevant desulphurization reactions were evaluated. Finally, full scale industrial trials were conducted. All three phases of the investigation will be discussed with the major emphasis being placed on the kinetic study."

Jan 1, 1996