Search Documents

By John L. Watson

The dewatering of steel industry waste sludges prior to discard or recycling often presents significant problems due to the fineness of the sludge particles, which may blind the filter medium and/or produce a cake with limited porosity, Several steel plant wastes, such as sludges from BOF and EAF gas cleaning operations exhibit not only a very fine particle size, but also some degree of magnetic character, A novel process has been developed to utilize the magnetic character of such sludges to enhance dewatering through a multi-force operation involving magnetic, chemical and vacuum forces, The process consists essentially of undertaking vacuum filtration of a flocculated sludge in a magnetic field, This is achieved by installing a permanent magnetic in a fixed position on the axis of a vacuum drum filter, thus effecting filtration of magnetic and non- magnetic particles, bound together in flocs, in a magnetic field, Previous tests using a modified laboratory vacuum drum filter treating artificial (magnetite) and industry waste (BF sludge) feeds have demonstrated that filtration capacity may be enhanced significantly with increases of up to 3000/0, An explanation of the mechanisms associated with the enhanced filtration was not obvious, and this research was undertaken to permit the cake formation in the magnetic field to be monitored to provide an insight into the manner in which particles agglomerate to form the cake. These tests revealed that the magnetic field caused magnetic particles to be aligned perpendicular to the filter surface and to form channels through which filtrate could freely pass thus increasing capacity, The effects of various magnetic fields and field strengths on the filtration process were also investigated. A simple computer model was constructed to demonstrate the proposed theory of multi-force dewatering, The model output graphically illustrated the suggested mechanism and confirmed the enhanced capacity of the novel dewatering process,

Jan 1, 1996

By A. K. Kyllo, G. G. Richards

"The formation and control of accretions is an important aspect of process operation for gas injection. The nature of the accretion formed can have a considerable effect on a process, especially on the life of the lance or the refractories in the tuyere region. There are three basic shapes of accretion formed on tuyeres; pipes, hemispheres and hollow-cored hemispheres. However, there are wide variations within these shapes. Generally, the type of accretion formed will depend on the injector design, certain operating parameters and the physical properties of the bath materials. This paper seeks to collect the results of previous and current physical and mathematical modelling together with data gathered from operating furnaces, to obtain a better understanding of the effects of process design and operating variables on accretion formation.IntroductionAn important consideration in the design of a gas injection process is the possible freezing of the bath either around the tuyere or on the lance. With proper design, freezing may be controlled to provide protection of the lance or refractory, and to avoid blockage. Improper design may lead to tuyere blockage and significant refractory or lance erosion. In view of this, a good understanding of the heat transfer in the injection region is essential.While tuyere blockage has been a persistent problem since the inception of submerged gas injection processes, the problem of accretion formation was not studied in detail until the development of the shrouded tuyere by Savard and Lee. A number of studies relating to accretion formation have been carried out since then, but there is still little information available relating the nature of the accretion formed to the design of the injection system.The build up of materials on lances is a similar problem, and may also be either beneficial or detrimental, depending on circumstances. Unfortunately, there is even less information available regarding build up on lances than there is relating to tuyere accretions. While the form of build up on lances is generally a simple coating of the lance, accretions on tuyeres tend to be more complex. Tuyere accretions tend to occur in one of three basic forms: pipe, hemispherical and hollow-cored hemispherical (Figure 1). However, there appears to be a considerable variation within these forms."

Jan 1, 1996

By D. M. Jones

Dust generation data have been obtained from 19 industrial Outokumpu flash furnaces. Statistical analyses of the data have been carried out and the most significant factors affecting dust generation evaluated. The results indicate that dust production may most effectively be minimized by: 1) Minimizing the distance between the molten slag and the furnace roof 2) Optimizing burner design and combustion parameters.

Jan 1, 1996

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By C. J. Hunter

Prior to the commissioning of the Sansu Sulphide Treatment Plant (STP), Ashanti Goldfields' treatment facilities were capable of producing some 700 000 ounces of gold per annum. Ore sources were underground refractory sulphides, surface oxides and old tailings dams. In order to increase the mines production to 1 million ounces per annum and to accommodate the change in ore sources as surface mining moved into fresh sulphides, a part of the strategy adopted was -the construction of a new sulphide treatment plant with a capacity to mill 2.2 million tonnes per annum and produce 400 000 ounces of gold. The STP has been designed, built and commissioned. and has been in operation since February 1994. The Plant boasts the world's largest Bio-oxidation facility which is capable of treating 790 tonnes of sulphide concentrate per day at a grade of 11.4% sulphur and is currently undergoing an expansion to increase its capacity to 1050 tonnes per day. The following sections describe the reasons for selecting the BioX® Process, the plant design, the commissioning experience and the plant performance to date.

Jan 1, 1996

By Frank Sames

A recently developed model is used as a tool to optimize blast designs based on the continuing combination of full scale blast assessment and performance prediction. The use of this tool has allowed to evaluate present blasting practices and proposed designs through a better under-standing of the influence of the various blast parameters. The empirical model has a modular structure covering all aspects of blast performance including 30 fragmentation, potential rock damage and 30 muckpile profile prediction. The modules are assisted by a terrain model which is compatible to most mine mapping systems, and a blast design editor. The evaluation is summarized in a blast management module. Various studies have recently been undertaken using the model to qualify and improve blast designs with respect to wall stability, optimized fragmentation and muckpile distribution, as well as to the control of the environmental effects such as blast vibration and airblast overpressure. To verify the predictions of the modeling, full scale blast assessment techniques were used to qualify blast geometry, explosives and initiation performance, rock movement, muckpile distribution, near- and far-field vibration levels and airblast ovepressures. The model provides a tool to gain an improved understanding of blasting and blast control. The modeling results are presented in a visual form which allows simple comparisons of proposed blast designs. Additionally, the model can be used for detailed analysis and blast management.

Jan 1, 1996

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By F. Patisson

During exothermic gas-solid reactions, heat generation makes temperature rise and modifies the rate of the various mass transfer processes, namely the chemical reaction itself, the pore diffusion and the external transfer. We have investigated this thermal effect during the oxidation of zinc sulfide porous pellets in a thermo balance furnace, between 550 and 900°C-and under O2-N2 atmosphere. The results have been' analyzed by using, firstly, the law of additive reaction times derived from the isothermal Grainy Pellet Model, and, secondly, a new numerical model taking into account non-isothermal conditions. Both the models can satisfactorily simulate conversion versus time, but the numerical model also depicts the temperature evolution within the pellet. Finally it is shown that owing to the heat generation the zinc sulfide oxidation takes place under diffusion control (3/4 internal, 114 external) in all the cases studied. During the course of reaction, the. pellet undergoes strong temperature variations, with thermal gradients confined to a shell oxide layer.

Jan 1, 1996

By C. A. Young

Cyanide is a toxic species that is found predominantly in industrial effluents generated by metallurgical operations. Cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent accidental spills. Various methods of cyanide remediation by separation and oxidation, including photolytic advanced-oxidation processes, are therefore reviewed. Reaction mechanisms are presented throughout the paper. The methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1996

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By G. Brien, O&apos

Selective in-plant breakage was investigated at a Central Queensland, Australia mine. Component seams and size fractions from in-plant samples were characterized petrographically and probability analysis of vitrinite reflectance data used to track the distribution of seam proportions through the plant. Results show that the 2 seams reported differentially to coarse and fine circuits, mainly as a function of coal type rather than rank. Seams were also preferentially concentrated in different size fractions of the coarse circuit. Breakage in the coarse coal centrifuge generated approximately 4% of -0.5 mm fines, but was not seam specific.

Jan 1, 1996

Prediction of fragmentation in Taconite Mining is an important aid to blasting engineers. A simple theory relates the intensity of radial fracture per unit length to distance from the borehole, from which a power law for mass fraction passing versus size is derived. For the lower end of the size distribution, the equation agrees well with several published examples of fragmentation from sieving of full scale blasts. Large size fragments arise from interaction of fractures from neighboring holes and pre-existing joints. Analysis of two assumptions regarding radial fracture interaction shows that complex fragmentation distributions can arise from the simple mechanisms proposed. Measured fragmentation falls between the two extremes calculated.

Jan 1, 1996

By Lanny Pasternak

"This article is directed at plant production, engineering and maintenance personnel. Seldom does any industrial operation take the time to study the costs involved in the generation of what is probably their most expensive plant utility energy source.IntroductionIn the typical industrial plant in Canada, a 200 hp, 900 cfm, air compressor costs about $60,000* per year to operate (Fig. 1). In 1989 when BC Hydro embarked on their industrial energy management program Airflow Energy Ltd. were asked to spearhead the “Efficiency Compressed Air” portion of that program with a mandate to perform onsite overview surveys and physical hands-on testing of some 300 selected industrial plants throughout British Columbia for compressor efficiencies and wasteful air leaks (Fig. 2). The program duration lasted until 1995, during which time a tremendous amount of data were amassed relating to equipment types, clients’ operating habits, end-use applications and operating costs.During the past six years, Airflow Energy also performed somewhat similar surveys but on a smaller scale in Alberta, Ontario, the United States and the Republic of China. It was no surprise to find some inherent equipment concerns related to efficiency as well as neglected energy wasteful air leaks, so British Columbia was not alone and the problems appear somewhat universal."

Jan 1, 1996

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By Guy L. Fredrickson

A modified transpiration reactor was used to measure the composition of the equilibrium gas phase formed above compounds in the Hg-O-S system at high temperatures (600 to 900K). A thermodynamic database {(AGo°f AH°t. AS°t)} for-HgO, HgS, HgSO4, Hg2SO4, HgSO4?HgO, and HgSO4?2HgO was developed based on the experimental results. Prior to this study, only estimated data were available in the literature for the sulfates and oxysulfates at temperatures above 298K. A series of vapor pressure' stability diagrams were constructed from 473 to 973K with isobars of Hg(g), HgO(g), S2(g), and SO3(g). These diagrams were found to be significantly different than those available previously and do provide insight to the phase relations of importance during the thermal processing of Hg-containing wastes. The thermodynamic results were used to conduct a series of Gibbs energy minimization calculations for a thermal processor' afterburner system for the treatment of HgS-containing wastes. The retention of Hg in the discharge calcine was examined as a function of temperature and excess air. Hg was found to report to the calcine as HgSO4, Hg2SO4, or HgSO4 HgO depending on the process conditions, and Hg retention occurs at temperatures as high as 930K. The precipitation of Hg-containing phases from cooled afterburner discharge gas starts at approximately 900K and the cooling of the gas an additional 30K (to 870K) results in over 50% of the Hg being preCipitated as HgS04?HgO. It was also determined that for small amounts of Hg present in sulfide concentrates during roasting, the Hg will be retained as HgSO4 or HgSO4?HgO at temperatures as high as 870K.

Jan 1, 1996

By Rejane Tubino Geyer

The volume of electric arc furnace (EAF) plus oxygen (BOF) slag produced yearly in the world is about 84 million ton. Because of this, the study of recycling processes as a way to solve the storage problem of these slags rise in importance. There are, however, some inconvenients on using this byproduct: lime, which takes part of the process of steel production, remains as a non-reactive raw product in the slag. Since lime reacts in presence of humidity, forming expansive compounds, slag use is strongly limited. There are some utilizations for the electric arc furnace and oxygen slag in the Civil Construction Industry, mainly as base, subbase and asphalt covering in highways. However, independently of the type of recycling, a period of "cure" of about six months is necessary. Because of this slow cure process this byproduct may turn non-competitive in some regions if compared, for example, with the natural aggregate. The objective of this work is to present the flowsheet of the slags production as a residue both at the electric and oxygen steel plants and, through a bibliographic review, to analize the possibilities and limiting factors for the use of steelmaking slags in the Civil Construction Industry.

Jan 1, 1996

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By Gunnar Persson

The borehole pressure/time history of blasting practice is simulated in a twin pendulum apparatus, where the expanding shotfiring gases force two steel slab swingers apart. A pilot installation built at SveDeFo is described. The relevant factors, that govern the use of this test method as a means of classifying explosives with respect to their toxic fume potential, are described.

Jan 1, 1996

By B. W. Cavender

Innovative mining and metallurgical operating techniques and processes can be identified and developed by analyzing changes as they occurs within the mine, plant, technology or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions and the development of new knowledge. Innovation can be organized, practiced and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically designed policies regarding organizational structure and staffing, daily management practices and compensation and incentives.

Jan 1, 1996