Search Documents

Gold Fields Ghana Ltd (GF Ghana) currently operates an underground mine at Tarkwa, in south--west Ghana. The mine was operated by Tarkwa Goldfields Limited, a wholly owned subsidiary of the State Gold Mining Corporation of Ghana (SGMC). The mine was making operating losses and in a poor state of repair. Tarkwa Goldfields retrenched all the staff and GF Ghana assumed management responsibility for its own account on I July 1993.

Jan 1, 1997

By R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1997

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By John A. Thorpe, Gary R. Maxwell, Kirk M. Schall, Kenneth A. Brunk

"Gold ores containing oxide and some sulfide copper minerals incur significant cost penalties when leached with cyanide, because 4-5 moles of cyanide are consumed for each mole of leached copper. This equates to ~4 kg of NaCN per kg of leached copper. Total cost of excess NaCN consumption plus CN destruction can exceed $4.00 per tonne of ore. AuGMENT Technologies has patents pending on a process that can 1) economically recover 70-80% of the cyanide that is fed to a mill, 2) produce salable copper cathodes, and 3) reduce the need for a cyanide destruction facility. Standard equipment for resin processing and electrowinning are used to recover the cyanide and produce the copper cathodes. Steps have been taken to determine: 1) how to develop the resin kinetics, 2) how much savings are incurred at a mill site, 3) how the novel 'electro-elution' circuit achieves efficient operation.IntroductionWhen gold ores containing nuisance copper are leached with cyanide, a significant cost penalty is incurred because 4-5 moles of cyanide are consumed for each mole of copper that leaches. This is equivalent to the use of -4 kg of NaCN per kg of copper that leaches. The total cost of excess NaCN consumption plus cyanide destruction can exceed $4.00 per tonne of ore.AuGMENT Technologies has a patent pending on a process that can 1) economically recover 70-80% of the cyanide that is fed to a mill, 2) produce salable copper cathodes, and 3) reduce the need for a cyanide destruction facility. This ACCS (Au-.C.u-.C.N Solution) Process Technology involves the novel application of copper cyanide chemistry. Standard resin processing and electrowinning equipment are used to recover the cyanide and produce the copper cathodes."

Jan 1, 1997

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Abstract-Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed surficial mapping and sampling programs in the Separation Lake area of northwestern Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of surficial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these surficial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t) values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sulfide mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from surficial samples was compared with that of in situ material. Gahnite from the peraluminous rareelement granite and pegmatite overlapped very well with surficial gahnite of Group 1. Gahnite from volcanogenic massive sulfide mineralization and Sedex-type mineralization overlapped well with surficial gahnite of Group 2. These results suggest that determination of gahnite composition in indicator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By M. C. Bétournay, J. E. Udd

"The Mining Laboratories of CANMET are the principal federal government vehicle for the delivery of mining research in Canada. With research being performed at five locations, which are mostly mining communities, the laboratories are in close proximity to the industry which they serve.The Mining Laboratories have three principal roles: (1) to support government in its development of policy; (2) to aid industry in the enhancement of productivity; and (3) to improve the health and safety of Canadians,both in the workplace in mines and around abandoned mine sites.From 1994 to 1996, CANMET’s mining research was re-focused into four programs. These are: (1) Underground Mine Environments; (2) Mine Mechanization and Automation; (3) Ground Control, and; (4) Coal Mining Health and Safety.In this paper, the authors outline the work of the Mining Laboratories and also identify the areas considered to be primary targets for future mining health and safety research in Canada."

Jan 1, 1997

By Kubik K

Recent significant advances in the Global Positioning System (GPS) have contributed to making real-time kinematic/dynamic process for decimetre to centimetre-level positioning more reliable and ready for the production-use. As a result of research and development efforts in this area, a robust real-time kinematic (RTK) GPS positioning prototype system has been established at QUT for both scientific and engineering purposes. This system is finding applications in a wide range of automobile robots or automatic guidance vehicle systems. This paper first summarises the theoretical basis necessary for centimetre real-time kinematic positioning, then gives a brief description for the real-time dynamic GPS system developed at QUT. The paper summarises the results of a designed vehicle tracking test. The results demonstrated that the differences between RTK filtering solutions and OTF solutions are in the order of magnitude of about 20 centimetres and the accuracy of OTF solutions are in the levels of two centimetres. This confirms that the RTK system delivers three-dimensional position with decimetre-to-centimetre accuracy. This particular RTK processing system is robust and reliable, although the system is referred to as a prototype and will be further developed.

Jan 1, 1997

By L. H. Lewis

The relationships that link microstructural properties of advanced permanent magnet materials with magnetic properties such as the coercivity are often difficult to quantify, especially in materials with nano-scale structures. Recent work on RE2Fe14B-based powders fabricated with rapid- solidification techniques such as inert gas atomization (IGA) and melt-spinning provide insight into the nanostructural features which affect the acquisition and stability of coercivity. In all cases the coercivity is found to be a function of both the scale of the constituent microstructure and of the presence and distribution of minor phases.

Jan 1, 1997

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton&apos;> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia&apos;s political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997

By R. Luo, R. V. Kumar

"The co-deposition of cobalt and nickel as a binary alloy has been studied by both cyclic voltammetry and long-period controlled-potential electrolysis. Cyclic voltammetry experiments showed that the cathodic current density for the mixed Co-Ni (Co-Ni=1:3) electrolyte is noticeably higher than that obtained on electrolyte containing single CO2+ or Ni2+ (II) salt of the same ionic strength. The onset potential observed for the mixed salts electrolyte was also less cathodic (negative) than that for the single metal salts, respectively. The effects of a number of operational and compositional parameters on the co-deposition of cobalt and nickel were studied. The parameters under investigation include cathode (deposition) potential, temperature, CI-/Sol ratio in the electrolyte, the amount of additives such as H3B03, and acidity of the electrolyte.Optimum operational conditions were established for the deposition of cobalt and nickel binary alloy. These results are discussed with respect to feasibility of reclaiming cobalt, nickel and chromium from mixed superalloy scraps by melt-refining (under nitrogen and/or ammonia), followed by electrorerining of cast anode for co-depositing Co/Ni and thermal decomposition of chromium nitride for recovering chromium metal."

Jan 1, 1997

By Richard R. Klimpel

This paper will summarize the trends resulting from the data generated in a large number of laboratory and industrial studies con- ducted by this author where various slurry rheology factors have been carefully changed and controlled. Factors such as percent sol- ids, addition and/or removal of fines, slurry mill filling level, specific material oriented breakage properties, chemical additions, etc. are discussed with a number of illustrating examples. This paper is specifically aimed at developing rheologically related operating guide- lines for plant engineers so that improved operating conditions can be selected.

Jan 1, 1997

Africa is rich in natural resources, much of which remain untapped. Despite that, international mining companies have largely stayed away from the continent due to political instability in many countries, lack of infrastructure and the inability to gain control of mineral deposits. Today, optimism is growing concerning African mining. Many of its nations are moving toward privatization of their mining industries. They see it as a way to improve the lives of their populations and become politically stronger. Ministers from 22 African nations were Denver, CO in June for the World Bank&apos;s Multilateral Investment Guarantee Agency&apos;s Fourth Annual African Mining Investment Symposium. The three-day symposium drew more than 400 mining executives and government representatives. Foreign mining investment in Africa is on the increase. In 1996, international mining companies spent about $418 million on exploration. That is more than double the $190 million spent in 1994. Mining executives say the mining climate in Africa is improving because countries are privatizing the industry and rewriting mining laws that encourage natural resource development. They estimate that private mining firms now control about 80% of mining today. Mine development will help lift the living standards for Africans, the ministers said. The average income for ordinary Africans is about $500 a year. If this new mining boom continues, citizens of nearly all African nations will reap the benefits of better infrastructure and government services, as well as more higher paying jobs, the ministers said. They also issued a word of caution to mining companies attempting to join in the African boom. Concerns are being raised about the treatment of villagers and the environment. In the past, foreign companies would "behave about like colonial masters," said Gerald Ssendaula, natural resource minister for Uganda. Africa is in a different position now, he said. "Now we are solving our own problems." Mining companies must respect local communities or risk creating unrest that will threaten fragile new governments, said Akolang Tombale, chief geologist for Botswana. On the other hand, he said villagers must accept that mining development will benefit them. "They feel these are their natural resources. There must be a mutual interaction between the companies and the people."

Jan 1, 1997

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

By Stanley I. M, Brett D, Dickson R

The Mt Lyell Mine, situated in Queenstown on the west coast of Tasmania, has a production history of more than 100 years. Previous mining activities have resulted in substantial modifications to environmental conditions at Mt Lyell and disposal of sulphidic waste rock across the lease has left a legacy of on-going environmental impacts including acid drainage (AD). In 1995 Copper Mines of Tasmania (CMT) was granted a mining lease Irons the Tasmanian State Government for redevelopment of Mt Lyell and indemnity from actions concerning pollution from previous occupation and use of leased land. The Environmental Management Plan (EMP) for the Mt Lyell redevelopment committed CMT to be responsible for waste rock dumps generated from their activities and to ensure that management is in-line with best practice environmental management principles. CMT commenced commercial production in December 1995 with sulphidic material from development of the underground Prince Lyell mine reporting to a single waste rock dump constructed according to a management plan developed in July 1995 and superseded by a management plan for extension in May 1997. The CMT waste rock dump currently has a total capacity of 220 000 m- and approximately 120 000 m3 of rock have been placed to-date. Material reporting to the dump is placed in a densely compacted state to a controlled surface profile. The dump is clay capped and a final revegetated soil layer placed on top. A rock pitched drain extends down to a wetland area in order to remove stormwater and minimise possible soil erosion on the revegetated sections. An integral part of the management plan for the waste rock dump involves characterisation of waste rock to identify geochemical rock types according to acid forming potential with provision for selective placement within the dump. High-risk materials are selectively placed and covered within the core of the waste rock dump, where possible, to control sulphide oxidation. Monitoring equipment has been installed in the waste rock dump by the Australian Nuclear Science and Technology Organisation (ANSTO) and an on-going monitoring program has been established to demonstrate the integrity of the dump cover as a barrier to the influx of atmospheric oxygen into the dump. The overall objectives of this program of work are to control the oxidation of sulphidic waste rock in the waste rock dump, minimise the risk of AD, prevent pollution of the aquatic environment and thereby demonstrate the integrity of the CMT waste rock dump management Strategy.

Jan 1, 1997

By Robert Martin, Brian W. Stump, David P. Anderson, W Scott Philips

Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The .CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treaty requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include 1) variation of amplitude of seismic energy at various azimuths from cast blasts, 2) identification of the extent of back failure following explosive removal of pillars, and 3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

Jan 1, 1997