Search Documents

By H. Itou, J. M. Toguri, T. Takasu

"Marangoni convection has a large effect on materials processing since it remarkably enhances heat and mass transport near a free interface. To have a better understanding of the behavior of Marangoni convection in molten salts, observation and calculation of the thermal convection in a column held between a pair of Pt disks (2mm in diameter) fixed to hot thermocouples, were carried out.Calculated flow patterns and absolute values of fluid velocity agreed well with the observed results. When the temperatures of both disks were set equal and the height of liquid column was 2.4mm, four vortexes were generated on the longitudinal plane with a typical velocity of 15mm/s . From the calculated isothermal lines, the behavior of the enhanced heat transport was obvious; fluid heated at the disks was conveyed to the free surface and the cooled fluid at the surface was conveyed to the inner region. Increase in the height of column and/or increase in the absolute value of applied temperature difference lead to increase in fluid velocity lineally in this calculation range.IntroductionIn the processing of many materials, fluid flow of melts has a large effect on refining capabilities and on the characteristics of the produced material. Marangoni convection is generated when a spatial gradient of interfacial tension exists on the free interface due to differences in temperature and/or concentration. This promotes heat and mass transfer locally near the interface.For example, Marangoni convection which are created following the dissolution of interfacially active materials, increases the local corrosion rate of refractories (1-3). In absorption and discharge of oxygen and/or nitrogen in a molten metal, the effective reaction rate of the gas components through the gas-liquid interface increases (4-7). Also in crystal growth, the distribution of defects and impurities in the crystal is affected and this can alter its quality (8-11 ). The temperature distribution is also affected and can greatly change the productivity. For these reasons, the effectiveness of Marangoni convection in refining should be quantitatively clarified and its control should be better understood."

Jan 1, 1997

By M. Boher, J. Lehmann, M. C. Kaerlé

"In the production of high quality steel, the understanding of the interactions between liquid steel and refractories and of their effect on steel purity and cleanness are becoming more and more important.An experimental study has been per-formed in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel. The results show a pollution of the liquid steel:•the silicon content of the liquid steel increases due to the reduction of the silica of the refractory by the aluminum contained in the steel; and•a reoxidation of the steel occurs and the formation of an oxide layer on the refracto-ry, mainly composed of spinel crystals and of Ca-aluminates is observed.The transfer mechanisms of the various elements are analyzed."

Jan 1, 1997

Resource rent tax is a form of taxation or royalty, which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax (APT). The implications of the current form of Additional Profits Tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine, if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of Additional Profits Tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation. Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional Profits Tax is both time and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory. A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with Additional Profits Tax. The review includes examples based on the structure of Additional Profits Tax which is levied in Papua New Guinea.

Jan 1, 1997

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By Haslam C. O, Los V. L, Abramson G. J

The technology applied by lonex Pty Ltd provides an important breakthrough in geochemical exploration, enabling the discovery of concealed mineral deposits to great depths below surface. Most mineral discoveries have been made in areas of outcrop or relatively shallow cover; deposits at greater depth have been beyond the range of conventional geophysical and geochemical methods. Quite apart from the need to explore to greater depths in regions of major current or past production, most continents have vast areas where prospective host rocks are concealed by more recent material. There are numerous case studies where Ionex methods have located deeply-buried metal deposits, up to 500 m below surface, beneath thick younger sedimentary, volcanic, or transported cover. Research leading to the development of this technology was initiated by Dr I S Goldberg at the Rudgeofizika Institute in St Petersburg (CIS), and the methods have been employed there - and in other countries - for many years. Ionex technology became available in Australia in 1993. It comprises: ò geochemical and geoelectrochemical sampling and ultra-high-sensitivity analysis for mobile and weakly-bonded elements (I S Goldberg); ò the delineation and interpretation of regional zones of enrichment and depletion of the prime elements within geoelectrochemical systems (GES) (I S Goldberg); ò the investigation and interpretation of the three-dimensional geochemical zoning within geochemical anomalies (G J Abramson); and ò multi-variate computer modelling of the geochemical fields and systems (V L Los). lonex technology has been adapted to the environmental conditions in Australia with the participation of C 0 Haslam.

Jan 1, 1997

By M. J. Sanzotti, C. J. Bise

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing waste rock into the void created by mining. The paper also examines scheduling the process as a unit operation of the mining activity. Based on a review of background literature and interviews with representatives of various mining companies, public-interest groups and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing at a southwestern Pennsylvania mine was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of longwall systems in the United States. Further, at the mine used in this case study, concomitant stowing would reduce subsidence by only 50% of what would normally be incurred during full longwall caving, and the longwall coal-production rate would decrease from 3,630 t (4,000 st) per shift in the nonstowing case to 1,360 t (1,500 st) in the stowing case. A preliminary cost analysis reveals that pneumatic stowing would add from $5.79 to $11.57 per t ($5.25 to $10.50 per st) to the operating cost of producing coal at the case-study site.

Jan 1, 1997

By Neil J. Duncan, Edward R. Langfield

A hydraulic rock breaker was developed in Germany by Helmut Darda and uses a wedge-plug and feathers mechanism powered by a 10,000 p.s.i. power pack. During the past four years these tools have been increasingly used all over North America for secondary breaking of boulders and rock. More recently, techniques have been developed to break rock off the solid in trenches and rock emplacements where blasting is pro¬hibited or very limited. Underground operations are commencing to adopt the splitter for scaling plus including systems which can be efficiently applied to chambers and mines. Mr. Neil Duncan, who was originally scheduled to give the main part of this presentation has, during this past month accepted a position with the Alberta Energy Resources Conservation Board in Calgary. The board encourages its members to take part in seminars such as this but, unfortunately, due to the heavy pressure of work, it was impossible for him to attend this conference. Mr. Duncan has, however, forwarded me his notes and suggest¬ions, and using these, combined with a slide presentation, we feel that we can quickly and clearly define the operations and application of the hydraulic splitting technique as it applies to your profession and tunnelling work. The first question that most of you are asking is, "Why use a hydraulic splitter if you can blast?" Our answer to this is that we are not advocating the use of hydraulic splitting where blasting is feasible - but, during the past decade many applica¬tions have arisen where blasting is not allowed, or restricted

Jan 1, 1997

[ ]

Jan 1, 1997

The most critical step in the development of any mining project is the completion of a feasibility study. The feasibility study has one primary goal; to demonstrate that the project is economically viable if it is designed, constructed and operated in accordance with the concepts set forth in the study. Starting from a mineral resource data base, the feasibility study will define the ore reserves, the mining methods, the mineral processing concepts and the scale of the project. The disciplined activity of developing a feasibility study leads the proponent to examine every aspect of the project, many of which might otherwise be ignored. All technical concepts will be established and the corporate philosophy with respect to organisational structure, social and environmental responsibility, infrastructure contributions and financing will be determined. All the major decisions about how the project will be developed are made during the feasibility study. The success of the project will then depend upon the assumptions and decisions in the feasibility study and the ability and empowerment of the development team.

Jan 1, 1997

By J. S. Oram

Maltby Colliery, operated by RJB Mining (UK) Ltd is successfully mining the Parkgate seam in Yorkshire at a depth of 1000m using longwall retreat. Extraction in the Parkgate seam is influenced by interaction from previous workings in the Swallow Wood Seam 160m above. The paper describes in-situ stress measurements and simple gate road convergence measurements carried out to assess the extent of the interactive influence. The stress measurements, obtained using the stress relief overcore technique, were carried out from a maingate development roadway in an area where the stress redistribution under an overlying pillar and adjacent panel goat could be measured. The measured vertical stress distribution confirmed a significant interactive influence with high imposed vertical stresses under the overlying panel edges. Simple roadway convergence monitoring stations established in the gateroads of a retreating panel and in the development gateroads of the adjacent panel, confirmed higher rates of roadway deformation relating to overlying panel edges and pillars, particularly in the areas where a vertical stress window developed during panel retreat. In addition to highlighting a close relationship between closure rate and the measured vertical stresses, the convergence monitoring proved valuable in establishing characteristic deformation behaviour under specific interactive influences and also in defining the optimum location, extent and time of installation u£ additional roadway support and reinforcement. The information from the measurement programme has enabled the Mine Management to gain a better understanding of the interactive influences on roadway behaviour and was instrumental in designing the layout of panels in an area of the North East district of the mine where previous experience had indicated the combined influence of high interactive stresses and weak roof lithology resulted in difficult strata conditions both at development and on panel retreat. The planned location of panels and gateroads took into account both mining operational considerations and the need to avoid potentially high risk interaction zones as highlighted from analysis of the monitoring results. To obtain additional data on parameters influencing roadway deformation, extended roadway convergence monitoring has been established.

Jan 1, 1997

By Edward (Ted) M. Dowey

Shaft 26B of New York City’s Third Water Tunnel was constructed by Frontier-Kemper Constructors, Inc. of Evansville, Indiana. The 176.8 m (580 ft) deep shaft will serve as the construction shaft for the Manhattan spur of Water Tunnel No. 3. Twelve m (40 ft) of over-burden was supported by a rectangular cofferdam. This shaft was excavated in 13 months, through 164.6 m (540 ft) of rock, using 24,040 kg (26.5 tons) of explosives. Concrete lining cycles included the installation of stainless steel pipes embedded in the lining as the shaft advanced. A total of 635 m (2,084 linear feet) of stainless steel pipe was installed.

Jan 1, 1997

By T. L. Brekke, T. R. Howard

Stability of an underground opening can be defined in several ways. To geologists and engineers that are used to working in geological environments where the major parts of the works after careful scaling can be left unsupported during the construction period as well as during operation, any rock mass behavior that requires reinforcement, support or lining may be regarded as a stability problem. To colleagues excavating underground openings in geological environments that require continuous use of reinforcement or support and lining "stability problems" are often associated only with those parts of the work where "standard" construction procedure and method of reinforcement or support and lining is inadequate, and special measures therefore needed. In either case, a major objective is to assess the stability problems correctly -as far as possible at the planning stage -- and choose methods for excavation and reinforcement or support that will bring the opening safely and as economical as possible through the problem areas. INTRODUCTION It is not uncommon that stability problems associated with faults or seams have been described as "unexpected." This term has unfortunately been used to indicate that no one knew that the fault or seam existed prior to excavation. A careful review of documented cases where serious stability problems have occurred revealed that the existence of these zones most often was known, but that their behavior was incorrectly assessed prior to or during construction. Miscalculations have been made in terms of the type and magnitude of loads that developed, and in particular in terms of the time-dependant behavior.

Jan 1, 1997

By Jay S. Gunasekera

Metal parts are traditionally processed by either filly-liquid (e.g., casting) or filly-solid (e.g., forging) state. Semi-solid metal forming incorporates elements of both casting and forging. In 1991, Gunasekera(5) developed a model illustrating the influence of flow stress by the liquid fraction. The result fits Kiuchi's (1979)(7) experimental data quite well. This model assumed the liquid part is surrounded by solid as small pockets inside the material, which is opposite to the real practical situation. Since the melting usually first happens at the grain boundary, it is better to treat the semi-solid material as small metal crystal surrounded by liquid.

Jan 1, 1997

By W. X. Wang, O. Stephansson

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification program for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1997

By James Wm. White

Computer-based mine management systems are being used in many surface mines to assign haul trucks, track equipment and manage information. Advances in digital communications allow these systems to be used in underground operations. Underground mine management systems help maximize production by providing gains in equipment and manpower use, drawpoint equalization in block caving operations, preventive maintenance and safety. Current systems use allocated or "locked" train and load-haul-dump (LHD) dispatching. Allocated dispatching rarely optimizes open pit product' on. But it offers an efficient mode of operation underground and where options are more limited. The primary objectives of underground mine management systems are to maximize production and mini¬mize contention time through allocated train, truck or LHD dispatching, traffic control, equipment monitoring and comprehensive reporting. The main components of an underground mine management system include: ? A central computer (personal computer or worksta¬tion) in a central control center. It sends instructions to train, truck or LHD drivers and allows dispatcher interaction. ? A field computer system (FCS). This consists of a touch-screen graphics console (GC) and mobile hub - on each train, truck or LHD to receive and display instructions from the central computer and accept driver input. ? A data radio network based on leaky feeder (data, voice, video) or microcell radios (data only) and advanced token-ring technology. This passes information between the central computer and the FCSs. ? Radio frequency (RF) tags mounted at boxes, weigh bridges, tips and rim tunnel main haulage ways to locate trains or LHDs (Luke, 1993). Such a management system must be in place before implementing computer-based dispatching (Vagenas, 1991) for production optimization.

Jan 1, 1997

By Andy Schroeder

Located in Hamilton, Ontario Canada, Berminghammer Foundation Equipment, is a manufacturer of advanced foundation equipment with 30 years of experience. The company is represented in more than 20 countries world wide, maintains an extensive Research and Development team, and has earned a reputation for finding the most practical solutions to the most challenging projects. The vertical travel lead, referred to as "VTL" system, was first developed and patented by C.W. Bermingham in the 1970's. This lead system was developed in response to the fundamental limitations of either a fixed lead or hanging lead system. The fixed lead system is well suited to level job sites with few obstructions and has the advantage of faster positioning of the lead, the hanging lead is very adaptable to different elevations and batter piles but takes much longer to position. Therefore the Vertical Travel Lead was developed to combine the advantages of fixed leads, fast and accurate positioning, with the ability to adjust the height of the lead base up or down. The VTL lead is connected to the boom by a sliding connection which allows the lead to be elevated or lowered below grade. The advantages of the VTL system were recognized by many foundation specialists and they have become the Industry standard in Canada , US Railway Construction , and many parts of the USA.

Jan 1, 1997

By J Deen, P Sterk, W Forsyth

Homestake Mining Company has made a firm commitment to develop a functional and cost effective perimeter blasting program. The goal of the program is to develop smooth, sound walls in all development ends. A good perimeter blasting method will improve safety, reduce waste rock handling, allow easier support installation and reduce scaling time. All the benefits will contribute to an overall reduction in total development costs.

Jan 1, 1997

By Y. M. Jubeli

"Abstract - Gamma-ray spectrometry, an effective tool in geological mapping, was used to define boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains. This paper describes the role of an airborne gamma spectrometric survey which was orginally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to significant modifications and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack sufficient geological data."

Jan 1, 1997

By A. Farzanegan, D. A. Lowther, A. R. Laplante

"Off-line optimization studies are often necessary to improve the efficiency of grinding circuits. These studies are primarily based on the mathematical modelling of processing units (e.g., ball mills and hydrocyclones) and computer simulations. To complete an optimization task, process engineers must possess skills and knowledge of different subtasks involved in such efforts, e.g., plant audit, laboratory tests, and data analysis. Such know-how can be in part provided by Knowledge-Based Systems (KBSs). One such system, being developed in C Language Integrated Production System (CLIPS), is presented here, with focus on the estimation of ball mill selection functions for the purpose of both diagnostic and simulation, and its use for the optimization of ball size. Some of the interpretation and diagnostic rules will be presented, as well as grinding kinetics and classification data likely to fire them.IntroductionSince the late eighties there has been a growing trend in applying Knowledge-Based Systems (KBSs) to mineral processing [Meech 1990, Bearman and Milne 1992). Table l lists some KBS (often referred to as expert systems) applications that have been used mainly as tools for improving on-line monitoring and control of grinding circuits. However, there has been fewer attempts to add the symbolic processing powers of KBSs to conventional off-line grinding simulators. Figure 1 shows a relatively standard procedure to perform an off-line optimization study [Napier-Munn and Lynch 1992]. In brief, a typical program includes taking representative samples from a number of streams, running laboratory tests on collected samples, estimating model parameters which describe physical processing units (e.g. ball mills and hydrocyclones) validating model predictions and using models for simulation trials. One inevitably needs to be familiar with concepts of process modelling and simulation as well as various computer programs to be able to complete all steps of the study. Much of this ""expertise"" can be captured by KBSs, given their inherent capabilities for symbolic knowledge representation and manipulation."

Jan 1, 1997

Industrial Minerals production in New Zealand is limited in both quantity and range, but imported in quantities that make New Zealand the world's biggest consumer per head of population. The use of industrial minerals is assured as both population and standard of living increase regularly. But to develop these minerals in the New Zealand environment requires the mineral, or its market (both local and export), to have characteristics that negate the remote geographical location. Volume and/or uniqueness can achieve this.

Jan 1, 1997