Search Documents

Both safety and productivity in underground gassy coal mines can be improved substantially if an appropriate gas management system is introduced. A strong direct relationship exists between the gas emission rate, roof and floor strata relaxation zones characteristic, mining activities and gas drainage practices. Detailed knowledge of geological factors, gas and coal-rock properties, as well as mining systems are necessary for the methodology used in predicting overall underground gassiness, and planning gas capture and ventilation systems. Early gas emission calculations for various mining activities, particularly for the longwall mining system are essential. A reasonably accurate prediction of gas make as well as the design of ventilation, gas recovery (drainage holes) techniques can be made using 'Floorgas' and 'Roofgas' computer simulations, provided sufficient geological, mining, and gas data are made available.

Jan 1, 1998

In most States of Australia it is a legislative requirement for underground mines to have a separate means of egress from the normal means of ingress to permit the safe evacuation of workers to the surface in event of an emergency. Such egress may be in the form of a ladderway equipped shaft/underlie or trafficable incline/decline. Additionally, there is a general requirement to have one or more airways, separate to the main shaft or other principal entrance of an underground mine, extending to the lowest level to permit ventilation to all parts of the mine. Fulfilling these requirement is difficult in the development phase of a mine when access underground is achievable by only a shaft or decline in the process by being sunk. What is frequently practiced in Australia is for production to then commence, sometimes in association with continuing development, in the same configuration without the establishment of this separate method of egress to the surface nor additional airway/s with reliance on refuge chambers to cater for back up in any emergency. Not only, could this jeopardise the health and safety of workers in case of an underground emergency it could be construed as a statutory breach of legislation. While recognising that refuge chambers are often used throughout underground operations nowadays their equipping and the criteria for their location needs to be bought into focus. This presentation discusses how such legislative requirement can be met alongside the use and appropriateness of refuge chambers.

Jan 1, 1998

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By M. H. Foroughi

This paper discusses the effects of seam inclination and lateral stresses on the stress distribution in pillars in inclined coal seams. The average pillar stress is a function of the overburden weight, the mine depth, the effective extraction ratio and the angle of seam inclination. Normal and shear stresses in the pillar are computed by numerical modeling. In medium dipping seams, leaving a pillar with its axis normal to the stratification causes a shearing stress concentration in the top and bottom corners of the pillar. This results in the pillar possibly becoming less stable in comparison to pillars in horizontal coal seams. Therefore, to reduce the stresses, it may be necessary to leave the pillar at an angle of b deviated from the normal axis to stratification. A mathematically approximate formula for determining b is proposed, and the results are confirmed by numerical modeling.

Jan 1, 1998

By James Su

The Green River Valley in Kent, Washington, is a fast growing area containing retail facilities, warehouse factories and industrial businesses, including the Boeing Space Center. Traffic from Interstate - 5 to the West Valley Highway is highly congested. Accordingly, a new corridor, including a bridge across the Green River, was designed and constructed between 1996 and 1997. This paper presents a case history of the design elements and issues associated with the construction of the pier foundations of the bridge. Subsurface conditions were evaluated using both deep test borings and CPT soundings to evaluate the strength and consolidation properties of the supporting soils. Subsurface conditions consisted of alternating layers of loose and medium dense silty sand and sandy silt. Engineering analysis included an assessment of liquefaction as well as pier supporting capacity and associated settlement. The constructed foundations included 6-foot-diameter piers cased to a depth of 120 feet below the ground surface. The pier casings were driven to the design tip elevation and the soil inside the casing was removed by drilling. Despite performing borings and CPT soundings at specific pier locations, occasional trees, buried thousands of years ago through geologic processes, were surprisingly encountered during pier construction. This presented unique and difficult driving and drilling conditions. During drilling, the water level inside the piers was maintained near the ground surface to create a balance of hydrostatic pressure and prevent boiling of soils the bottom of the casing. After the casings were installed, the soil inside the casing was excavated, the rebar cage was installed and the pier was filled with concrete using treme techniques. Construction of the piers is complete and the completed piers have experienced negligible settlement. Owner: City of Kent Engineering Department Timothy La Porte, Project Manager Kent, Washington General Contractor: Mowat Construction Company, Kirkland, Washington Foundation Contractor: Condon - Johnson & Associates, Inc., Tukwila, Washington

Jan 1, 1998

By Katsuya Kase, Kaname Takeya, Keaji Ohmori, Yoshiyuki Asakawa

"The reduction-diffusion process (the R-D process) using Ca as a reducing agent has been practiced in industry in the production of the SmCos type, the Nd-Fe-B type and the 1b-Fe-Co type magnetic materials. The advantages of the R-D process are the generally high yield of rare earth metals and the single-stage conversion of a mixture of oxides and metal powders into a product of rare earth alloy powders. On the other hand, one of its disadvantages is the slightly high contents of oxygen and calcium. This disadvantage is remarkable in the Nd-Fe-B type. Singe-phase Nd2Fe14B alloy powders with low content of 0 and Ca, is obtained by choosing appropriate raw materials and performing the R-D process in a controlled way. These alloy powders are very suitable for the production of Nd-Fe-B sintered magnets and expected higher magnetic properties by adopting advanced magnet production method.IntroductionThe hard magnetic rare earth transition metal intermetallics, especially, have attained considerable technical importance. Examples are the alloys based on the intermetallics SmCo5[1], SmC017[2], NchFet4B[3], or the recently developed alloy SnuFe11Nx[4]. The reduction-diffusion process using Ca as a reducing agent has been well known as an economical method of producing rare earth based magnet materials[5]. The reduction-diffusion process has been practiced in industry in the production of the SmCos type, the Nd-Fe-B type and the 1b-Fe-Co type magnetic materials. The advantages of the reduction-diffusion process are the generally high yield of rare earth metals, the single-stage conversion of a mixture of oxides and metal powders into a product of rare earth alloy powders, the elimination of the crushing process of the alloy ingot, the inessentiality to special equipment, etc. On the other hand, one of its disadvantages is the slightly high content of oxygen and calcium. This disadvantage is remarkable in the Nd-Fe-B type. An outline of basic studies of the reduction-diffusion process was reviewed from the particular viewpoint of the production of magnet materials by Ogawa [6]."

Jan 1, 1998

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter's availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter's Environmental Project are also included in the paper. Information on 'the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper's focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By David W. Mogk, Tamara Darsow, Macgregor L. Fogelsong, Robert M. Hunter, Frank M. Stewart, Edwin H. Abbott, Courtney A. Young

Abstract: Development of cost-effective techniques for recovering precious metals from their ores has been the goal of metallurgists for hundreds of years. Today, metallurgists are increasingly called upon to design processes for ores that are refractory to conventional recovery techniques. These challenges and the addition of environmental costs (including site remediation) to the total cost of mining have stimulated a search for alternatives to conventional processes, such as cyanidation. This paper describes the progress made to date in development of an innovative alternative to cyanidation, termed bisulfide leaching, for extracting gold, silver and platinum-group elements from refractory ores and concentrates. While bisulfide leaching can be implemented abiotically, significant benefits accrue from its practice as a bioprocess that integrates the steps of precious-metals liberation and extraction. In many applications, bisulfide leaching appears to offer significant advantages over the traditional cyanidation process. Dissolved bisulfide and hydrogen sulfide are much less toxic than dissolved cyanide and hydrogen cyanide. Recommended workspace exposure limits and harmful concentrations for hydrogen sulfide gas are higher than those for hydrogen cyanide gas. While the facilities required to practice the bioprocess on an industrial scale would be similar to that of cyanidation plants, chemical reagent costs could be 80 percent less. The bioprocess may also offer advantages in the leaching of ores and concentrates that are not amenable to cyanidation. For example, bisulfide leaching of ores containing carbonaceous material may produce higher gold recoveries if the "preg-robbing" characteristic of the material can be controlled biologically or with dissolved sulfide binding. Moreover, in that precious metals are much more soluble than base metals in bisulfide solutions, bisulfide leaching offers distinct advantages over cyanidation for selective dissolution of precious metals from base-metal concentrates. Thus, the bioprocess uses the natural sulfur cycle to mitigate pollutant production and to enhance precious-metals recovery.

Jan 1, 1998

By M. H. Col

Within the last few years, there have been numerous techno-logical advancements within material handling due, in part, to the introduction of conveying systems and mobile material handling systems to the industry. Although the traditional material handling methods are still commonly used, the introduction of conveyors to the industry has provided companies with some very efficient and economical options. These "new" systems change with the industry to accommodate rigorous demands, ease of operation, and low operating cost requirements. The number of mobile material handling systems utilized in mining operations is increasing, especially in heap leaching applications. Ten years ago, mobile material handling systems like Mobile Stacking Conveyors (MSC) were considered a novelty. There were two (2) MSC's in actual operation and only one of those in a heap leaching application. Today there are numerous proven systems operating at mine sites around the world-La Coipa, Zaldivar, Florida Canyon, Cananea, El Abra, Chuquicamata, and Radomiro Tomic. The popularity of mobile systems is due to the benefits realized by individual projects. As technology advances, so do the concepts behind mobile material handling systems. Implementing self leveling mechanisms, Programmable Logic Controllers, and Global Positioning Systems to control the equipment are just a few of the recent advances that will be discussed in this paper. We will also discuss current proven systems, and touch on what we see as some of the future advances.

Jan 1, 1998

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today's terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By Deepak Malhotra

Comminution circuits in general account for fifty percent of capital and operating costs for a processing plant. Significant advances have been made in optimization of these circuits. One would expect a few circuits to be the favored designs for plants. Review of grinding circuits worldwide indicates that a variety of circuit designs are utilized for non-technical reasons. A brief review of circuits and reasons for their selection is given in this paper.

Jan 1, 1998

By Thornton D, Esterle J, La Rosa D

Control of blast fragmentation has a significant impact on coal mine profitability. Two approaches for the characterisation of coal blastability, particularly in terms of fines, are presented. Both approaches were implemented for the predictio

Jan 1, 1998

By I. R. McGowan, J. Tilk, J. I. Hershman, R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1998

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1998

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998

Application of flotation for the removal of hydrophobic compounds from soils was studied. Bench scale flotation tests were conducted on artificially contaminated soil, using both conventional mechanically agitated machine and flotation column. Flotation parameters tested include surfactant collector type, conditioning time, flotation time, surfactant dosage, pulp pH, solid/liquid ratio in conditioning and pulp temperature. It is found that with conventional flotation 74% removal of the contaminant was achieved from soil particles in the range of 75-830 µm; with column flotation up to 80% of oil could be removed from the 250-830 µm soil fraction, and 65% from the 75-830 µm fraction. Flotation was found to have considerable potential for cleaning up contaminated soils.

Jan 1, 1998

By Florian Kongoli

Non-ferrous smelting slags .can contain magnesia, which substantially increases the liquidus temperature. One option to counter this increase is to flux with calcia. In this work, experimental liquidus measurements including new measurements on industrial slags have been compared with a FACT-based thermodynamic model, which predicts the liquidus surface of multi-component iron silicate smelting slags containing both magnesia and calcia. The predictions, which agree well with experimental results, are summarized in both isothermal and non-isothermal diagrams to give a quantitative description of the liquidus surface.

Jan 1, 1998