Search Documents

By C. Sui

A common objective in many Cu/Zn concentrators is to reduce the loss of Zn to the Cu-concentrate. One suspected source of the problem is accidental activation of sphalerite by heavy metal ions such as lead. One method of quantifying surface metal ion concentration is extraction with ethylene-diamine-tetra-acetate (EDTA). This was used to survey Cu-rougher flotation at three Cu/Zn concentrators: Les Mines Selbaie, Falconbridge's Kidd Creek division, and Hudson Bay Mining and Smelting Although all have less than 0.2% galena in the ore, Pb ions proved an abundant extractable metal. From a laboratory study a model of surface coverage of lead species generated by an ore was combined with an estimate of surface concentration of lead required to activate sphalerite to explore the possibility of accidental activation. Ores with Pb-grade as low as 0.1% can produce sufficient Pb to be a potential problem.

Jan 1, 1999

By Romeo Jurani, Ralph Dresel, Fred Kissell, Charles Parker

This report describes actions taken to control silica dust at the Yucca Mountain Exploratory Studies Facility (ESF), a tunnel located in Southern Nevada that is part of a scientific program to determine site suitability for a potential nuclear waste repository. The rock is a volcanic tuff containing significant percentages of both quartz and cristobalite. Water use for dust control was limited because of scientific test requirements. A major dust reduction was achieved with an intermediate air cleaning station located on a rear deck of the TBM trailing gear.

Jan 1, 1999

By Stephen Navin, Pablo Ferradas, Carlos Silvestri, Alexander Markov, Jon Kaneshiro

In the high Andes of Peru, two tunnels are being constructed totaling nine kilometers in length at an elevation of over 4,500 meters. The tunnels convey freezing and crystal-clear waters from rainfalls, streams, and lakes for the consumption of Lima. The drill and blast 3-meter wide by 4-meter high tunnels are being driven from both ends through folded and sheared volcanic tuff, andesite, agglomerate,and limestone, where groundwater inflow is high. This paper describes the design geological and groundwater inflow investigations and construction.

Jan 1, 1999

By A. A. Odunaike, E. G. Okafor, M. H. Mokwe

Microscopic Studies were performed on ore samples from the Muro banded iron ore deposit in Nigeria and the Marampa iron ore deposit in Sierra Leone. Ore characteristics that affect processing of both ores were compared with a view toward assisting mineral processing engineers in choosing the most suitable methods for upgrading the ore. The Nigerian ore contains 30% to 37% (by weight) Fe and the Sierra Leonean ore contains 34% to 51% (by weight) Fe. Hematite is the main iron mineral in both ores. The Sierra Leonean ore is relatively coarse grained (typically around 250 µm) and can be upgraded by conventional gravitational methods. In contrast, the Nigerian iron ore is fine grained and must be ground to -74 µm to liberate the hematite for recovery by flotation. Both ores contain high percentages of phosphorus and sulfur, which are above the required specifications for direct reduction and blast-furnace practice. These deleterious elements can be rejected by grinding and flotation.

Jan 1, 1999

By A Vigar

Siliceous float sampled in the Wafi River by CRA Exploration in 1977 assayed 22 g/t Au and 89 g/t Ag. Follow up in 1979 led to the discovery of outcropping mineralisation now known as Zone A. Soil sampling in 1980 and 1982 outlined a 350 m by 400 m area of >1 g/t Au at Zone A and smaller areas at Zones B, C and D. Thirty-one diamond holes were drilled between 1983 and 1986. Elders Resources continued evaluation of Zone A under a farming agreement between 1988 and 1990. Mineralised diorite porphyry was discovered in 1990 by drilling conceptual targets 500 m to the NE of Zone A. Evaluation of this copper-gold porphyry became the main focus of exploration for the next five years and a substantial resource was outlined within a single, discrete body. A review of the paths to project development in late-1995 highlighted the need for increased resources via a second mineralised porphyry and/or an additional resource of Zone A size to make the project viable. It was concluded that the greatest immediate potential for increasing the resource inventory was at Zone A itself where the mineralisation was open in all directions. Detailed mapping and drill core logging lead to the geologic and structural models being revised in early-1996. The objectives of the 1996 drill program were to extend the Zone A resource, to test for continuity of mineralisation westwards to Zone B, to better define the controls on gold mineralisation and to delineate high-grade blocks amenable to selective mining by infill drilling and 3D orebody modelling. The last drill hole of 1996 intersected 30 m at 4.6 g/t Au from 273 m in WR147, deep in the western limit of Zone A. This intersection gave impetus to continue drill testing towards Zone B. In April 1997, hole WR154 was drilled 100 m to the west of WR147 and intersected 20 m at 8.5 g/t Au and 70 m at 11.0 g/t Au at similar depths near the diatreme contact. Drill hole WR155 was then drilled 100 m to the west of WR154 and intersected 86m at 5.7 g/t Au and WR159 drilled 100 m to the south of WR154 intersected 36 m at 9.2 and 50 m at 4.4 g/t Au. A significant zone of essentially blind, high-grade gold was discovered beneath the dipping flank of a poorly mineralised diatreme in what became known as the Link Zone. The long history of evaluation has been driven by the conviction of a dedicated team that a mineralised system of the size and complexity of Wafi with strongly anomalous gold in outcrops over the entire Mount Golpu area must contain economic mineralisation hidden within it. The keys which redefined the direction of exploration and lead to the discovery of the blind, high-grade gold Link Zone were, in our view, the critical review of the project status, detailed geological and structural studies to define clear exploration targets and the necessary funding and persistence to carry this through.

Jan 1, 1999

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By N. Parra, M. N. Herrera, T. Vargas, C. González, B. Escobar

The bioleaching of mineral sulfide pulps in a bench-scale rotating-drum reactor was studied. The reactor contained horizontal paddles on the inner wall for lifting the mineral pulp. The performance of the reactor was tested by bioleaching a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans (ATCC 19859). The concentrate was efficiently bioleached at a 50% pulp density with the drum operating at from 0.5 to 1.0 rpm. Attempts at bioleaching the concentrate at the same pulp density used in a conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows the process to operate at much higher pulp densities than conventional stirred-tank reactors. This results in improved bacterial activity because of better attrition control of the mineral particles.

Jan 1, 1999

By John L. Watson

Many metals-based industrial processes experience limitations in their operations due to an inability to effectively separate solids and liquids where partidesizes are less than 25 microns. Steel plant sludges ,generated, from the cleaning of furnace off-gases represent a typical example of processing difficulties attributable to material characteristics, and recycling or even efficient disposal of these materials is often a major problem. The use of a magnetic field to augment the traditional mechanisms of vacuum dewatering has, been demonstrated in previous work to have significant value in separating solids and 'liquids, where the solids exhibit some magnetic character. Magnetic vacuum dewatering has been used with magnetite ores and with blast furnace sludges and magnetic fields have been incorporated successfully in drum and disk vacuum filters. The research described in this paper investigates the use of magnetic seed material and flocculants to extend the application of magnetic, vacuum filtration to non-magnetic pulps. It is shown that the addition of a flocculant can enhance the capacity of drum and disk magnetic fIlters when treating materials, such as steelmaking sludges, which are only partially magnetic. In addition, the use of seed magnetite with a flocculant is shown to improve the dewatering of fine hematite pulps in a drum magnetic filter. However the use of a flocculant and seed magnetite had only limited success in improving filtration in a disk magnetic filter with a fine quartz pulp. A disadvantage of magnetic vacuum filtration with seeding appears to bean increase in cake moisture due to water entrapment in the floes resulting from agglomeration and magnetic attraction.

Jan 1, 1999

By J. E. Gebhardt, L. Piga, G. Schena

The possibility of beneficiating a low-grade alunite ore from the Tuscany region of Italy was examined. Flocculation and flotation techniques were investigated to separate alunite and kaolinite from the ore, which also contained feldspar and quartz. Flotation was performed at pH 6.5 with oleic acid as collector and sodium silicate as dispersant. A concentrate containing 12% alunite with a recovery of about 65% and a concentrate containing 28% alunite with a recovery of 84% were achieved from the -38-µm feed samples containing 5.0% and 12.9% alunite, respectively. Poor recovery of alunite was achieved by flocculation methods.

Jan 1, 1999

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By Ovidiu Pasca

Several improvements in converter equipment and operation at BHP Copper have reduced the converter cycle time as necessitated by an increase in flash furnace output. The resulting higher intensity performance of the Peirce-Smith Converters has had a major impact on the dust handling and off-gas cleaning systems. This paper describes work carried out on the design of a new converter hood with particular reference to the thermal analysis and hood performance aspects. Changes in converter cycle time and campaign life as result of the process and equipment improvements are discussed in a separate paper.

Jan 1, 1999

By C. Villa Diniz, A. H. Martins, Fiona M. Doyle

It is proposed that battery grade MnO2 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By D Craw, P V. Angus

Gold mineralisation at Macraes occurs as late quartz-carbonate veins within a body of sheared and hydrothermally altered Otago Schist, the Intrashear Schist. The alteration is characterised by the presence of rutile and the absence of epidote and titanite, indicative of an alteration fluid containing >10 mol per cent CO2. In areas of high strain, a fabric of black microshears develops, gradational to mylonitic cataclasite in the high strain zone adjacent to the hanging wall of the duplex shear zone. The microshears contain hydrothermal graphite, inferred to have been deposited from a methane-rich fluid. The mylonitic cataclasite is characterised by abundant pyrite, the absence of albite and extreme grain size reduction. Gold recovery in the CIL processing plant at Macraes can drop to 50 per cent or lower for some unfavourable ore types. Preg-robbing by a component in the ore, possibly graphite, was suspected as the cause. Mylonitic cataclasite was identified as the lithology responsible for the poor recoveries, with the capacity to bind about 30 ppm of gold in the leach tanks. A program of detailed geochemistry and quantitative grain-size measurement using Coulter analysis was undertaken to identify specific mineralogical factors associated with preg-robbing. The results indicate that pyrite, graphite, and extreme grain-size reduction are the factors associated with highly preg-robbing ores at Macraes. The evolution of the mylonitic cataclasite is accompanied by strong potassium enrichment, as muscovite, and depletion in sodium as albite is removed. This suggests that a simple powder XRD ratio of the albite to illite peaks would suffice to distinguish the preg-robbing ore for grade-control purposes.

Jan 1, 1999

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

Mechanical and electrical (M&E) systems in road tunnels are constrained by the traffic envelope and the construction profile. Whilst these spatial constraints are often ælocked inÆ early in the design process, the detailed M&E design continues for some considerable time after key civil engineering issues have been resolved. Ventilation design criteria for both normal and emergency operation often involves considerable negotiation with a wide range of stakeholders. Final system performance and spatial requirements are only finally resolved when suppliers are selected following the tender process. Lighting design is dependent upon a wide range of factors including tunnel lining materials and associated colours as well as agreed maintenance regimes. Cabling systems can only be developed when the general arrangement for power distribution is agreed and a system of substation, switchrooms and equipment rooms is in place. Many other systems such as fire protection and communications facilities fill the available space beyond the traffic envelope, where physical, structural and æsight lineÆ requirements must all be accommodated. The more co-ordinated civil engineering and M&E design is and the earlier the process starts the better the outcomes for all parties.

Jan 1, 1999

By Lamar S. Todd

The direct production of metal from a sphalerite concentrate is an attractive route for primary zinc. A series of operations and conditions have been selected to efficiently cause the following overall exothermic reaction. The process uses a continuous circulation of molten copper for material and energy transfer between the unit operations. Sulfide concentrate is reduced with an excess of superheated copper to make a copper alloy and white metal. The alloy is stripped of volatile metals under vacuum and some metals can be separately condensed. The residual copper and the white metal are fed into a copper converter to be blown with oxygen for desulfurizing and the superheated copper is recycled. The paper will include a detailed material flow sheet for the process, discussion of the operating conditions of the individual units, behavior of minor elements, and zinc quality.

Jan 1, 1999

By Arthur J. Borst, Joseph P. Gildner

In a recent National survey, Seattle topped the list for having the worst daily traffic congestion. To address this problem, Sound Transit is planning to build 40km (24 miles) of light rail, including ten kilometers (six miles) of twin tunnels with four subway stations 40 m (130 ft.) to 65 m (210 ft.) deep. The overall schedule is very aggressive and Sound Transit is preparing four separate heavy civil construction contracts for simultaneous underground construction. Three of these contracts are being considered for design-build. Final design will start in March2000 and all underground construction must be completed by the end of 2005.

Jan 1, 1999

By S. Hadley, M. Placha, M. Mishra, V. Choudhry

Under a DOE-funded project, four advanced flotation technologies (the Jameson cell, the Outokumpu HG Tank Cell, an open column and a packed column) were evaluated at the benchscale to identify the technology or combination of technologies that best improved fine coal recovery and reduced processing costs. The results indicated that two-stage application of the Jameson and packed column cells provided the optimal performance. Subsequently, proof-of-concept scale testing was conducted at the Cyprus Emerald Coal Preparation Plant. The results confirmed that levelized production costs were lower using two-stage cleaning with the Jameson cell followed by the packed column.

Jan 1, 1999

By Y. Akin, M. S. Celik, T. Batar, F. Arslan

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, the boron minerals colemanite, ulexite and borax undergo decrepitation, shrinkage and expansion, respectively, upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot-plant studies conducted in our laboratories on the calcination of boron minerals are briefly reviewed and their implications to commercial operations are discussed.

Jan 1, 1999

By R. M. Clowes

Lithoprobe is a collaborative, multidisciplinary research project which is providing new insights into the tectonic evolution of the North American continent through its work within ten study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of tectonic processes which lead to the development of ore deposits. In mining camps, seismic reflection methods have proven effective in imaging shallow to moderately dipping litho logic contacts as well as structural features, and in some cases have been used for the direct detection of ore bodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 1999