Search Documents

By Christian Hecker

An Eh-pH electrochemical sensor developed for on-line pH and redox potentials copper sulphide flotation process control was studied. The electrochemical sensor cell includes two metallic platinum electrodes, a metallic antimony electrode and a high impedance reference cell which are polarized with a potentiostat. For pH and redox potential determinations, the Sb and platinum electrode potentials are measured, respectively, against the polarized electrochemical reference system. The behaviour of this electrode configuration has been investigated in a laboratory scale. An electrochemical sensor device has been succesfully installed and checked in El Teninte Colon Concentrator's SAG line feeding the copper flotation rougher circuit.

Jan 1, 1999

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

It is well documented that drill and blast outcomes affect the downstream mining processes of loading, hauling, crushing and grinding but it can also significantly impact on mine profitability via dilution, recovery percentage, lump generation (iron ore), fines generation (coal, iron ore), coal loss and final wall stability. Drill and blast must therefore be optimised to improve the overall profitability via positively impacting on productivity and saleable product generation. It is however, difficult to achieve this because of the complexity of the number of parameters that must be integrated and managed across the entire mine value chain, ie the concept of æMine to MillÆ. This paper highlights, via a simple case study, the need to have a mineÆs drill and blast system both in control (so that it is predictable to a high degree) and with minimal variability (so the design actually makes it into the field). This type of management control is essential prior to optimisation work being undertaken. The æTeam ApproachÆ is discussed to illustrate the methodology of achieving drill and blast optimisation. A case study is presented to illustrate the potential benefits of this approach which in this mine represented a 27 per cent reduction in powder factor with the downstream functions achieving higher productivity with the same or reduced maintenance costs. It is essential for Australian mineÆs to implement the appropriate management strategies and experienced personnel placement to ensure that their mineÆs drill and blast system is correctly managed to facilitate the optimisation of profit. Without this, the Australian mining sector will become increasingly uncompetitive.

Jan 1, 1999

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

This chapter looks at the development and use of the operating budget. This is management's plan of action in the short term, usually one year. The operating budget includes all expensed production costs (i.e., all costs reported as cost of goods sold) but does not include expenditures on capital equipment, which are usually justified using discounted cash flow techniques.

Jan 1, 1999

By Claus Becker

In Europe, approx. 50 km of traffic tunnels are under construction using Slurry-or EPB Shields or Convertibles of all sizes, among them the biggest slurry shield ever built up to now with 14,20 m diameter. Main characteristics and special features of the machines will be explained relating to geology, cover and water pressure. This gives a comprehensive overview of the latest developments of this kind of machines.

Jan 1, 1999

By Changshou Sun

Excessive deformation occurred in the underground openings of Jinchuan Nickel Mine, the largest nonferrous underground mine in China. Developed in weak rock formations at great depth, the underground openings are under great in-situ stresses with the horizontal stress being twice as high as the vertical one. Based on in-mine observations and in-situ testing results at the mine, time-dependent mite element simulations with coupled creep and plasticity constitutive models were conducted in this study to analyze the stability of underground openings In the study, the Burgers creep model and the Drucker-Prager plastic model were coupled to simulate underground drifts and cut-and-fill stopes. Two-dimensional finite element models were developed with ABAQUS - a comprehensive finite element simulation package The study investigated the behavior of underground drifts at great depth with high horizontal stress and the behavior of cut-and-fill stopes with various stope heights and fill conditions. The numerical simulations revealed important characteristics of opening deformations as a function of time after excavation and location relative to the wall of opening The results had good agreement with field monitoring data, They provided useful information to aid mine engineers in the design of mine openings, the selection of opening supports and the determination of support installation procedures.

Jan 1, 1999

By Lluís Fontboté, François Lieben, Robert Moritz, Massimo Chiaradia

"Abstract - The Las Cañas stratabound Pb-Zn deposit, in northern Chile, is hosted by the Lower Cretaceous back-arc marine carbonate and subordinate andesitic volcanic and volcaniclastic rocks of the Chañarcillo Group, one hundred meters above a thick pile of magmatic arc-related basaltic to andesitic lavas of the Bandurrias Formation. The deposit is not obviously related to local intrusive rocks, which include an Upper Cretaceous granodiorite batholith and dacite dikes emplaced along normal faults. Stratabound Pb-Zn-Ba mineralization is constrained within several porous stratigraphic units, including a 50 cm thick lapilli-tuff and less well mineralized algal-laminated limestone. Veins that locally carry some Pb-Zn occur along normal faults that displace the stratabound orebodies, and this study shows that they represent a different type of mineralization.Fluid inclusion microthermometric data for ore-stage quartz and barite indicate saline fluids (6 to 30 wt% NaCleq) and a formation temperature in the range of 80°C to 160°C for the stratabound mineralization. Two types of fluid inclusions occur in the veins. The type I vein fluid inclusions indicate less saline (average 7 wt% NaCleq) and slightly higher temperature fluids, in the range of 110°C to 220°C. The type II vein fluid inclusions indicate highly saline fluids (25 to 40 wt% NaCleq) which might be related to minor copper mineralization.206Pb/204Pb, 207Pb/204Pb and 208Pb/204Pb ratios for galenas from the stratabound mineralization, with mean values of 18.42, 15.59, and 38.25, respectively, fall within the range of stratabound polymetallic deposits of northern and central Chile, and indicate a Lower Cretaceous magmatic rock source. Galenas from veins have slightly more radiogenic 206Pb/204Pb, 207Pb/204Pb and 208Pb/204Pb ratios, with mean values of 18.47, 15.61, and 38.34, suggesting two distinct episodes of mineralization.?34S values for galena and barite range from negative values (-31.2‰ to -12.5‰ and -7.7‰ to +12‰, respectively) in the mineralized tuff to higher values in the algal-laminated limestone (-2.5‰ to +1.2‰ and +13.2‰ to +17.4‰, respectively), close to Lower Cretaceous marine sulfate values for barite, and homogeneous values for the galena from veins (-12.0‰ ±1‰). Changing redox conditions can partly account for ?34S variations in the tuff. Sulfur sources include magmatic rock sulfur (-1.5‰ to +9.7‰) as well as sedimentary sulfides and marine sulfate."

Jan 1, 1999

By A. B. Isaeva, A. Yu. Lein, A. A. Karpenko, V. V. Serova, A. P. Lisitzin, V. Yu. Rusakov, V. N. Lukashin

Abstract - The flux of sediment matter was determined using sediment traps near a black smoker ("Saracen’s Head," Broken Spur hydrothermal field) and the mineral and chemical compositions of the settled matter were examined. The metallic minerals are represented by Fe sulfides (pyrite and pyrrhotite), and Cu and Zn sulfides are also found in small and equal quantities. The hydrothermal suspended matter contains abiogenic calcite in amounts comparable to that in Ca sulfates. The content of silica and, specifically, of amorphous Si is unusually low. Such correlations between chemical elements and minerals, together with the isotopic compositions of S and C, are characteristic of a relatively young and active stage in the evolution of a hydrothermal system. Sediment traps within and under neutrally buoyant hydrothermal plumes collected biogenic material in addition to hydrothermal components. Microbial chemosynthetic production of organic carbon near the hydrothermal vent is comparable to primary production in the euphotic layer. Fe, Zn, Ca, Si, Ba and P are enriched in particulate matter in comparison to the background. A vast compound plume containing the discharge of multiple hydrothermal vents was found to the south of the Broken Spur hydrothermal field.

Jan 1, 1999

By Surendra K. Mishra

The increasing volume of wastes being generated by industry is a legacy of the industrial revolution and subsequent industrial growth. Social and regulatory pressures have been mounting on industry to improve its waste management practices. In many industrial sectors, waste disposal has been the only method of waste management. Land farming, underground burial, deep wells and incineration are still practiced. Often, concentration and volume reduction of waste streams are also practiced to reduce the waste management costs. In the recent years, there has been emphasis on waste minimization. Since the 19th century, industry has practiced recycling of usable resources as a way of handling unwanted byproducts. The mining industry has recovered or extracted economic minerals from tailings for decades. For example, during the gold rush period of 1970s, extraction of gold from tailings dams became economically attractive. Similarly, when it was economical, coal and shale fractions have also been recovered from tailings and refuge materials for commercial uses. In the steel industry, with the development of new furnace technology, recycling of flue dust and scrap iron was practiced as early as in the 19th century. Before 1900, there was little incentive for the industry to reduce the waste volumes. Manufacturers, however, did see a rationale for adopting profit-increasing techniques. They made an effort to recover and recycle economic materials from waste sources. One of the pioneering examples of resource recovery is the coke making industry. As the industry was market driven, products recycled from coke batteries included ammonia for use in fertilizers, gas for power generation and heating, and tar for road construction, wood preservation and roofing. Tar had been avery troublesome waste byproduct. But it quickly became a valuable chemical raw material, providing the foundation for Germany's dominance of the world's dye and medicine markets before World War I. Similar trends evolved in the chemical industry. In the context of current environmental regulations and escalating mining and processing costs, recycling of re- [ ] sources is becoming economically more attractive. Solid and liquid wastes generated by industries contain a range of inorganic and organic contaminants. Among these contaminants, metals and hydrocarbons form major groups. Treatment of these wastes is essential to meet regulatory disposal requirements. In the recent years, based on the principles of chemical and mineral process engineering, processes have been developed to treat these industrial wastes. This article reviews some of the processes that have made impacts and have proven to be effective at commercial scales.

Jan 1, 1999

By N Van Buc, E Coroiu

The rapid socio-economic growth of Hanoi City coincides with a corresponding growth of the transport demand. Today, the transport in Hanoi is completely dependent on private modes of transport. Because of the lack of an efficient public transport system and the expected rapid increase in traffic volumes, the movement of people and goods in the urban areas of Hanoi will cause congestion in the present city transport network. The solution of the construction of new roads, or the widening of the existing streets, is very expensive in urban areas and usually causes many social problems due to the resettlement of people. From the point of view of the number of inhabitants, Hanoi City is now over one million. Above this number the international experience shows that the public transportation must be a mass transport system with large capacity, commercial speed and also independent as much as possible from the street network. According to the Hanoi Master Plan for 2020, the Hanoi urban population will be over 3.5 million persons. Also, in the next 15 years, the distances between centre-destination points will be doubled by comparison to 1995.

Jan 1, 1999

Liebherr Mining Equipment Co., of Newport News, VA and Baxter Springs, KS, introduced the T282, a new two-axle, diesel-electric, AC drive haul truck with a payload capacity of 327-t (360-st). The T282 was unveiled at a press briefing in October 1998 at the company's Baxter Springs research and development1 manufacturing facility. In addition to an increase in pay- load capacity, the truck's AC drive system has been de- signed to allow for easy configuration to a trolley-assist system with minimal additional equipment. The T282 provides fuel savings, reduced maintenance requirements, and reduced downtime and maintenance costs, providing the mine operator with increases in productivity. Basic dimensions and weight of the T282 are: ? Overall length, 14.5 m (47.5 ft). ? Overall width, 8.7 m (28.7 ft). ? Loading height, 6.5 m (21.2 ft). ? Height - body up, 13.9 m (45.9 ft). ? Empty vehicle weight, 201 t (221 st). ? Operating weight - loaded, 528.6 t (582.6 st). ?Engine, Detroit Diesel 16V4000 at 2 MW (2,750 hp). ?Electric drive system, Siemens/Liebherr.

Jan 1, 1999

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By G. Cifuentes

It is known that the cathode purity and the electrolyte treatment are affected by the solids present in the electrolyte. Anodic slimes properties (e.g., chemical composition, crystalline composition, sedimentation) were studied in copper electrorefining. These properties were modified through anodic composition and current density. In this investigation, we have worked with anode material from the Ventana Smelting, Hernan Videla Lira Smelting (ex - Paipote) of ENAMI (National Mining Company) and El Teniente Smelting of CODELCO-Chile (National Corporation of Copper of Chile). The characterization of the anodic slimes was done as a function of current density and anodic composition.

Jan 1, 1999

In the past two and a half years, over 40 000 metalliferous mining and related services personnel have been trained through an Australian Generic Safety Induction system. This is almost half of AustraliaÆs metalliferous mining related workforce. This remarkable industry acceptance and delivery of safety courses is supported by Acacia Resources, Great Central Mines, Homestake, Newcrest Mining and WMC Resources, amongst hundreds of other mining, exploration and major contracting and services companies. MARCSTA; the Mining and Resources Contractors Safety Training Association (a pro-active not-for-profit self-help group of 24 major contracting companies) developed this generic safety induction. MARCSTA set out to find the æcommon groundÆ necessary to help address the evident safety problems and cost of re-training that were plaguing development of an internationally competitive and productive export industry. The incredible expansion of Australian mining during the decade fuelled a need for out-sourcing, resulting in much larger numbers of contractors on-site. At the same time, changes within Australian legislation, community expectations and the development of huge fly-in/fly-out operations and widespread skills shortages led to a rapid labour turnover and a higher paid workforce. Many Australian mining houses also ran international operations, particularly in South East Asia and head hunted people across the world. The skill levels fluctuated and fell at some local operations. Employers could no longer rely on systematic in-house training of permanent employees to improve safety and productivity as workers could and often did move on. Serious discrepancies in both quality and quantity of safety induction training and work practices occurred. Repetitive, boring and ineffective safety training became an embarrassing and costly burden for companies and workers alike. Then a spate of mining deaths sparked highly publicity, workforce concern and a demand for improvement from government, unions and corporate stakeholders. MARCSTA recognised it had to develop a high-quality safety-training program to satisfy the needs of all employers and be acceptable to others within the industry. This induction system had to be flexible enough to meet differences in legislation between states and industry sectors and be portable to enable cost and time savings for the new transient workforce. Changes in the last two years as a result of evaluating and incorporating various Taskforce inquiries into underground mining fatalities later led to the development of the MARCSTA Underground Safety Induction. This logical development added to the run away success of MARCSTAÆs General Safety Induction and was seen to be essential for many surface mines that were planning to develop underground operations. There are many lessons that MARCSTA learnt during its development that Pacific and South East Asian mining operations can benefit from. The most important of these are the support of stakeholders within industry and the recognition of higher safety and health expectations from workers and government. This goes hand-in-hand with the productivity and return on investment expectations of companies and their shareholders.

Jan 1, 1999

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999