Search Documents

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

Dump site injuries occur in all major mineral industries. Working in elevated areas near an edge is a common hazard for operators of off-highway mobile mining equipment. In this Information Circular (IC), serious injuries involving haulage trucks working at dump sites are examined for the period 1988 to 1997. Data were acquired from injury reports gathered by the Mine Safety and Health Administration (MSHA). The IC is organized into three sections. The first presents an overview of the frequency and severity of injuries. The second analyzes injury characteristics using MSHA-defined data fields and author-defined injury classifications. Key findings are discussed in the third section. In summary, 370 serious injuries were identified that involved trucks at dump sites, of which 26 were fatalities. Although haulage truck activities at dump sites resulted in a small proportion of the total number of injuries at surface mines, these injuries were much more likely to result in death or significant amounts of lost time than most other surface mine injuries. These findings support the belief that haulage truck activities at dump sites are worthy of continued study by those interested in improving the health and safety of workers at surface mines.

Jan 3, 2001

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometry of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers, and management and will help mine operators plan the optimum mining sequence for different mine geometries and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2001

By M. N. Semenoff

On July 8, 1999, EPA announced the RCRA Cleanup Reforms, a set of administrative reforms designed to achieve faster, more efficient cleanups. This paper will discuss the Reforms, the status of their implementation and assess these potential impacts on the mining industry.

Jan 1, 2001

By Minh H. Pham

This paper presents a technique for imaging the extent of solidification of molten metal flowing in a cooled pipe based on the concept of eddy currents. A 3D mathematical model, which relates the geometry of solidification to the scattered field induced in a solenoid external to the pipe, is derived. The model is described by a set of integral equations which are solved numerically using the moments method. An iterative algorithm is developed to reconstruct the solidification distribution image. Experimental measurements have shown that the eddy current technique is sufficiently sensitive for practical purposes.

Jan 1, 2001

By G. W. Bonnell, D. A. Young, D. G. Genter

Through 1996 and 1997, CANMET and the Cape Breton Development Corporation (CBDC) conducted a project to study the Phalen Mine’s 7 East longwall ventilation network to help determine methane emission patterns that were having a negative impact on coal production. Increased methane emissions were primarily related to mining depth and were also affected by the influence of a large sandstone body located above the worked seam. The research included the installation of tube bundle systems to monitor waste (gob) methane and pressure differentials. The focus of this paper is on the novel use of tracer gas techniques that helped shed light on the performance of the ventilation system and in determining the methane migration paths in the waste.

Jan 1, 2001

By B. D. Wood, J. A. Fowler, H. S. Grütter, J. M. Kong

Abstract- The phased approach used by De Beers for diamond exploration is briefly outlined. The Victor kimberlite is one of 19 kimberlites in a cluster near Attawapiskat, Ontario. The progress at the Victor kimberlite is summarized, and the operations are described within the framework of this staged approach. An evaluation program is currently under way on the Victor kimberlite, but although results are encouraging, insufficient diamonds have been recovered to permit disclosure of estimates for the grade and value.

Jan 1, 2001

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By Junji Shibata

Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal salts by using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versa tic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxalate powders obtained in this process. The analysis by using EDX showed that the two metal oxalates were distributed uniformly at the same ratio as the organic phase composition.

Jan 1, 2001

By Rick L. Williamson

International lending institutions have charters requiring projects that are seeking loans to adhere to certain environmental performance standards, including compliance with host-country environmental laws, as well as observance of international environmental policies and guidelines. The most commonly applied international environmental policies and guidelines are those established by The World Bank. Lenders require a review by an independent engineer to determine that the feasibility study plans have been developed in accordance with the applicable environmental commitments. Lender agreements require independent engineer evaluation of environmental performance through the construction phase and initial operations phase of the project, culminating in the issuance of an "Environ- mental Completion Certificate."

Jan 1, 2001

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By Robert Hanson, Mayur K. Patel

"Pneumatic conveying pipelines are used throughout a variety of industries, from food processing/packing to power generation plants, as an efficient means of transporting materials between storage and processing points. In general, different phases of pneumatic conveying exist when material is conveyed from point A to point B in a pipeline. This depends on the operating pressure and the material conveyed. Lean phase conveying exists when pipelines are operated at high airflow rates, relatively low pressures, inducing sufficient turbulence for particles to become entrained in the air stream. Thus, particles are conveyed along the pipelines at velocities in the range of IS-2Sm/s. Generally, the initial capital costs for lean phase system is low, however the running costs are high. The opposite is true for dense phase, high-pressure systems. In considering either conveying system, it is important that the rate of erosion of the pipeline be considered when designing such a system, since it is the rate of erosion that dictates the lifetime of components. In general, the high level of erosion occurs for lean phase flows, where high impact velocity contribute substantially to the rate of erosion as well as other processes such as particle breaking, if the particles are friable. This would lead to poor quality of material, not normally desirable. On a positive note, the process of erosion is used in other applications, which benefits from this process, e.g. abrasive guns.The failure, by puncture, of pneumatic conveyor bends in industry causes several major problems. Two of these are: (a) escape of the conveyed product causing health and dust hazard and (b) repairing and cleaning up after punctures necessitates shutting down conveyors, which will affect the operation ofthe plant, thus reducing profitability.The paper reports on modelling strategy used in the development of a modelling framework and the initial validation phases of the models incorporated within. The modelling framework encompasses Computational Fluid Dynamics (CFD) related engineering tools, based on Eulerian (gas) and Lagrangian (particle) approaches, to represent the two distinct conveyed phases, to represent the erosion process which is used to ascertain the lifetime of conveyor bends."

Jan 1, 2001

By Ray Walton, Ron Colquhoun, Ken Thomas, Dwayne Fentie, Barney Burke

"The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources.The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3% year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.BACKGROUNDAs early as 1992, Barrick’s Goldstrike Mine, located north of Carlin, Nevada had indications of the ore becoming ever increasingly carbonaceous in nature. As the open pit and underground exploration programs proceeded to step out over the years that followed, the accumulative amount of carbonaceous refractory ore and tons had become significant. By 1997, 29 million tons of double refractory carbonaceous ore containing an estimated 11.6 million ounces of gold had been identified. By 2000 the resource had increased to 14.3 million ounces."

Jan 1, 2001

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

By Harry Siewert

"The commissioning of the 4th concentrator (C4) at Freeport Indonesia in early 1998 increased total mill throughput from 130k to 230k tonnes per day. The C4 flowsheet consists of a single 38 ft diameter SAG mill, four 24 ft diameter ball mills followed by four banks of 4,500 ft3 WEMCO flotation cells.The design of the C4 rougher flotation circuit was based on the expectation that the copper and gold recoveries achieved with the 4500 ft3 flotation cells would be equivalent to or better than that achieved with the 3,000 ft3 flotation cells in the 3rd concentrator (C3) rougher circuit. This assumption was due to the fact that the C4 flotation feed size would be less than 15% +212 microns compared to the C3 rougher flotation feed size of less than 23% +212 microns. By mid 1998 it had become apparent that the C4 rougher flotation copper and gold recoveries were below those predicted.In order to determine the cause of the lower recoveries, stage by stage rougher flotation surveys were performed in all four concentrators. The results of the surveys showed that the C4 rougher flotation circuit had a lower recovery of +200 micron material than that achieved in the C 1, C2 and C3 concentrators. Through mineralogical analysis, it was determined that a majority of the copper contained in the +200 micron fractions was liberated and recoverable. This paper describes the steps taken to increase coarse particle recovery, overall plant recovery and the results achieved."

Jan 1, 2001

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

By A. Boucher, D. Marcotte

"Abstract- The accepted practice for the estimation of thin (2D) vein deposits recommends the use of the grade x thickness service variable (i.e., the accumulation). Grade estimates are obtained indirectly by the estimated accumulation/estimated thickness ratio. This practice stems from the varying support (thickness) problem and the resulting non-additive nature of the grade variable. We compare the actual performance of the direct grade estimation approach used by some practitioners to that of the indirect approach using accumulation. Our simulated and real data indicate that the direct approach is more accurate for point grade estimation where the grade-thickness correlation coefficient is positive (and vice-versa). Moreover, the relative gain of the direct method increases with the (positive) correlation coefficient. This finding contradicts common thinking that the indirect approach should be the preferred method where grade-thickness correlation is strongly positive. Also, for a given positive grade-thickness correlation, the relative gain of the direct method increases with the coefficient of variation of the grade and thickness. Résumé - L’estimation de veines minces (2D) minéralisées est normalement réalisée à l’aide de la variable auxiliaire épaisseur x teneur (i.e., accumulation). Les estimés des teneurs sont alors obtenus indirectement du rapport accumulation estimée/épaisseur estimée. Cette pratique découle du problème du support variable pour la teneur, l’épaisseur de la veine, qui fait que la teneur est alors une variable non-additive. Nous comparons les performances de l’estimation directe de la teneur, utilisée par certains praticiens, à celle de l’approche indirecte. Pour l’estimation ponctuelle des teneurs, nos données simulées et réelles indiquent une meilleure justesse de l’approche directe quand la corrélation teneur-épaisseur est positive (et vice-versa). De plus, le gain relatif de la méthode directe s’accroît avec la valeur de cette corrélation (positive). Ce résultat contredit l’opinion répandue que l’approche indirecte devrait être utilisée en présence de forte corrélation positive de la teneur et de l’épaisseur. Nous montrons également que pour une corrélation positive teneur-épaisseur donnée, le gain de l’approche directe augmente avec les coefficients de variation de l’épaisseur et de la teneur."

Jan 1, 2001

By Paul Worsey, Delbert Da, Eric Achelpohl

The University of Missouri-Rolla is currently researching the concept of using glass microspheres in explosives as taggants as part of a 3-year technical project funded by the Bureau of Alcohol, Tobacco, and Firearms. These taggants are intended to provide two functions, first explosive detection and second post explosive event identification. The key priority is being able to detect explosives used in terrorist acts prior to detonation. The research on the use of microspheres includes the development of indicator taggants for the purpose of revealing the presence of hidden explosives, by either emitting radiation when bombarded with neutrons or emitting selective vapors, such as DMNB which may be readily “sniffed”. Of secondary importance, after an illegal explosion, the tags serve to identify the lot number, etc of the explosive. This information is to aid in the tracking, arrest, conviction and imprisonment of the perpetrators.

Jan 1, 2001