Search Documents

By Roy McKinstry

In March of 2001, Barrick Goldstrike became the first surface gold operation in North America to evaluate the advantages of electronic detonators. A detailed study was conducted to quantify the benefits of the use of electronic detonators to the downstream excavation, crushing and ore processing operations. The following methods were used to quantify blast performance: High speed film and video monitoring Firing time and rock response analysis of the high-speed films Digital fragmentation analysis of the post blast muckpile Vibration waveform analysis (including Fast Fourier Transforms and seed waveform modeling) Excavator performance quantification Crusher, SAG mill and ball mill performance evaluation Ore recovery analysis Cost/benefit analysis

Jan 1, 2002

By D. Bernabe

The mine scheduling process defines a mining sequence across the life of the mine and stipulates the amount of ore, waste, and specific blocks to be mined each year so that the highest economic return can be obtained under a number of constraints. There are a number of mine scheduling software packages available. Each claims to be the best scheduler by maximizing Net Present Value (NPV) or by minimizing overall mining costs. These mine scheduling programs follow different procedures and scheduling philosophies based on either mathematical or heuristic principles. There was no study in which the mine production scheduling procedures applied by these packages were discussed and compared. This paper evaluates four open pit mine scheduling programs recently developed and compares them in order to determine if significant differences exist among them. The same input data, which consist of a 3-D block model, an economic set of parameters, and the initial surface topography for a operating copper mine in Southern Peru, was used to test each technique. The following programs were investigated with respect to their ability to optimize the NPV for the case study. 1) M821V1 Scheduler by Mintec; 2) NPV Scheduler by Earthworks; 3) Milawa Scheduler by Whittle Programming; and, 4) Fundamental Tree Scheduling Method (FTSM) developed at the Colorado School of Mines. The results from this case study demonstrate that the scheduling software packages, Mintec, Earthworks, and Whittle obtained similar NPV’s, while FTSM scheduler gave a six percent higher NPV than the other schedulers.

Jan 1, 2002

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By K. Wangerud, B. S. Caruso

A water balance model with deterministic and stochastic components was developed and used for the Gilt Edge Mine Superfund Site, South Dakota, to evaluate risks of contaminated runoff discharging to surface waters based on assumed water treatment plant (WTP) rates for different remedial alternatives. The objectives of the modeling were to use a stochastic approach for analysis of precipitation based on historic records, and for probabilistic estimation of annual and monthly runoff from primary disturbed/mining activity areas that currently requires, or will need, treatment at the WTP, water storage and changes in a major pit, and risk of contaminated water bypass of the WTP to a downstream drainage. Subareas/source areas generating contaminated runoff requiring treatment were delineated. A simple water balance model was used based on precipitation inputs and evapotranspiration and groundwater losses. Annual and monthly precipitation records for Lead, South Dakota were used to estimate precipitation at the mine site. A lognormal distribution was estimated for monthly precipitation. The stochastic software package/Excel add-in “@Risk” was used to generate random monthly precipitation values using a Monte Carlo method based on the distributions. The average annual and monthly distribution of pan and lake evaporation, and groundwater losses were also estimated for the site. Stochastic outputs from the model for the end of each month and year included contaminated runoff requiring treatment, water storage in mine pits and the risk of WTP bypass given different assumed WTP rates. The probability of the time required to dewater the pits was also modeled.

Jan 1, 2002

By B. C. Jago, H. Derbuch

"The Freightrain kimberlite is located on the Brodeur Peninsula, Baffin Island, Nunavut. Twin Mining is exploring the pipe and adjacent land (79 claims/655 km2) using a combination of airborne geophysics, soil sampling, diamond drilling, trenching and bulk sample processing. The pipe originally was discovered by Cominco Limited in 1975, re-evaluated in 1993 by Lumina Investment Corporation, when it was staked as the Zulu pipe, and subsequently covered by three claims in 1998 by Helix Resources who called it Freightrain.The Freightrain pipe coincides with a strong, ovoid-shaped aeromagnetic anomaly. It is the only surface exposure of kimberlite within a 30 km long linear trend of fourteen aeromagnetic anomalies that are up to 600 m in diameter.The pipe is exposed in the crater facies, near the transition into diatreme facies as indicated by the occurrence of pyroclastic kimberlite characterized by abundant olivine macrocrysts, juvenile lapilli and kimberlite autoliths set in a serpentine-calcite matrix. Olivine, Cr-pyrope garnet and chromite are the most abundant macrocrysts; clinopyroxene, ilmenite and phlogopite mica occur in minor to trace amounts. Garnet and chromite harzburgite, garnet lherzolite, garnet-spinel lherzolite and rare eclogite dominate the xenolith population.Garnet and chromite mineral chemistry indicate encouraging diamond prospectivity and that potentially diamondiferous garnet and chromite harzburgite were the principal sources of diamond in the mantle at the time of kimberlite eruption.Single clinopyroxene grains define an ~42 mW/m2 sub-continental geotherm that is rooted in the diamond stability field. This compares to a slightly hotter geotherm (~48 mW/m2) for adjacent Somerset Island kimberlites with an origin in the graphite stability field. This data accords with the general lack of sub-calcic Cr-pyrope garnet, diamond inclusion chromite and diamond in Somerset Island kimberlites."

Jan 1, 2002

By Bobby Michael (Mike) Roberts, G. M. (Mike) Bernard, Ronald R. Kelly

This paper describes Cananea's successful implementation of the world's first mobile high angle conveyor (MHAC™) to achieve multiple-lift stacking of their primary crushed (2,500 mtph) low-grade ore. The mobile high angle conveyor answered Cananea's needs to stack a second lift, 30-meter high, on their Quebalix I pad. The mobile high angle conveyor is a custom unit that was designed by Terra Nova Technologies (TNT) in conjunction with Continental Conveyor and Equipment Company (CCE's 100th HAC). The stacking system expansion project also includes a rail mounted tripper on the existing overland conveyor and a custom designed "corridor conveyor" to build the corridor for the upper mobile HAC tracks and tail of the existing mobile stacking conveyor. Mexicana de Cananea, part of Grupo Mexico, is a large copper producer in Sonora Mexico and has been in operation continuously for over 100 years.

Jan 1, 2002

By Michel Bustamante

The Arbre viaduct, 200 metres long, is the most important structure on the Belgian portion of the High Speed Train line between Paris and Brussels. The particular geotechnical conditions of the soil with carboniferous limestone affected by karstic phenomena, has prompted the designer to found the viaduct on systems of high capacity vertical and batter micropiles. The design of the working micropiles was validated by full scale tests performed on instrumented micropiles. The size of the structure and the deformation criteria to be met when HS trains are crossing the viaduct, together with the lack of references for such innovative structure, called for monitoring the movements of the piers as soon as the link was open to traffic. The authors report on the results of loading tests on micropiles and the results of settlement structure monitoring for a period of 4 years. Settlement of the foundation is estimated taking into account the group effect.

Jan 1, 2002

By Mark Kuchta

A new database application for long term production scheduling has been developed for LKAB's Kiruna mine. The scheduler uses a new block data structure whereby the monthly production data for three raw ore products are predetermined on a month-by-month basis for each production area that could be mined within the schedule time horizon. The production schedule is created by assigning the starting dates to the each production area subject to various mining operational constraints such that that the monthly deviations for the production targets are minimized. The system is well integrated into the mine's overall computerized mine planning system.

Jan 1, 2002

By Tony Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and Laurel Hill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereonet, and rose diagram projections so that the Loyalhanna's structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts. pillar sizes, etc., that lessen miner exposure to these hazards.

Jan 1, 2002

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

The Beverley uranium mine û now in production in the remote north of South Australia at1000 tonnes per annum û was established to meet a projected, but little-recognised shortfallin primary supply of uranium for the nuclear industry in the early part of the 21 st century. Inthe context of AustraliaÆs lack of bi-partisan support for uranium mining and the nuclearindustry, a four to five year window of opportunity existed from 1996 to establish the mine.During this period, Beverley achieved a number of firsts including: the first ISL mine inAustralia; the largest ISL mine in the world and the first to produce more than 500 tonnes ofuranium in its first year; the first to be established under a new Native Title regime in SouthAustralia; and the first to be established under a revised South Australian Mining Act.Beverley was brought into production against the background of: hostile opposition fromanti-nuclear activists; a suspicious and at-times hostile media; a regulatory and politicalcommunity that was unfamiliar with ISL mining; commercially unsophisticated Aboriginalgroups; an inexperienced engineering industry; and the vagaries of development in a remote,semi-arid location with neither population nor infrastructure. The lessons that can be learnedfrom Beverley showed that û like much in life û flexibility and timing are crucial.

Jan 1, 2002

By Paul Pedini

The challenge of Contract C19E1 of Boston's Central Artery Project called for the construction of two roadways under the commuter rail yard at North Station. Two options were offered for the method of their construction: Slurry Wall Roof-First or Soft Ground Tunneling. The instability of the indigenous soils seemed to rule out the use of tunneling, so the slurry wall method was chosen. However, these soils were incapable of holding up during slurry trench excavation. After many episodes of ground loss on early panel excavations, Modem Continental Construction suggested a method of trench wall stabilization. The Contractor (MCC) both suggested wall stabilization method and requested that the owner participate in the funding for the effort. The Project and the Contractor were able to agree on a solution which resulted in collapse-free excavation...and found an innovative way to fund the solution.

Jan 1, 2002

By B. Bichel

For the last 70 years, molten blister copper has been transferred by rail in hot metal cars from the Copper Cliff Smelter to the Copper Cliff Copper Refinery (ex Ontario Refining Company) where it was processed in two (2) reverberatory anode furnaces by poling with logs, cast on four (4) wheels, and then electrorefined. This practice was modernized in 2001 with the installation of two (2) rotary anode furnaces at the. Copper Cliff Smelter which employ steam and. natural gas for reducing and which provide a significant reduction in emissions. A new casting shop with a single anode casting wheel is used to cast regular and stripper constant weight anodes which are transported by truck to the Copper Cliff Copper Refinery for anode preparation and electrorefining. This paper provides an overview of the copper circuit at the Copper Cliff Smelter and a description of the CDN$31 million capital project.

Jan 1, 2002

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Bao Xiancheng

Jinlong's copper flash smelting process started up in April 1997. In the early days of production, lots of equipment and process problems were encountered. But, through continuous improvements in equipment and operation, the designed productivity was reached two years later and the smelting operation has been greatly upgraded since then. After more than 4 yew of production, we have made great achievements, such as increasing the flash furnace availability, significant improvements in operation control, optimization of concentrate burner's structure and operation, and smooth operation of the whole smelter. This paper outlines Jinlong's operational achievements made after commissioning, and discusses problems that were encountered and their countermeasures. Operational experience is also summarized

Jan 1, 2002

By K. Nona C. Liddell

There is a significant amount of early work that has been largely forgotten that deals with the validity of the pseudo-steady approximation for liquid-solid reactions. Much of this was originally published in the chemical engineering literature but is highly relevant to hydrometallurgical processes. The purpose of this paper is to summarize some criteria that were been developed by various authors for determining the error associated with use of shrinking core models for liquid-solid systems.

Jan 1, 2002