Search Documents

By Adrian C. Dorenfeld

Laboratory data form the basis for the design of flotation circuits. These data, obtained from testing samples of the ore, should show the optimum con- ditions for concentrating the ore and the effects of change in process vari- ables. Among the more important variables commonly met in flotation practice are: Liberation Size-This is the particle size at which substantially all of the valuable minerals are detached from the gangue minerals. Reagent Additions- Experimental data will show the reagents used and their quantity, quality, and point of addition. Pulp Density-This is an important variable in the design of the flotation circuit because it is one of the factors determining the size and number of flotation cells. Flotation Time-The time necessary to make the separation into concentrate and tailing depends on such factors as particle size and reagents used and must be known for determination of the size and number of flotation cells in the plant. Temperature of Pulp-Temperature affects flotation reactions. Water at approximately room temperature is satisfactory for most flotation separations, but some minerals such as fluorspar are best floated in hot water. Type of Circuit-Many types of circuits can be designed, as discussed in detail later. The laboratory tests should provide data for design of the plant circuit best suited to the ore. Water-Knowledge of the quality of the future plant's raw water is important because water quality may drastically affect flotation results. If possible, flotation tests should be made using samples of the water to be used in the plant. Flotation results may vary with seasonal temperatures and with circulation of reclaimed water. Experimentation can show whether it will be necessary to provide for heating, cooling, treating, or reclaiming the water. Uniformity of Ore-The extent of variation of the ore in hardness, grind- ability, mineral content, and floatability should be investigated so that the designer can ascertain methods to overcome problems caused by ore variations. Settling and Filtration Data-To design the plant flotation circuits, settling and filtration rates and ultimate percentage solids of the various products must be determined. Corrosion and Erosion-Corrosion and erosion tests should be made on the flotation pulps, particularly if the pulps are acid or at an elevated temperature, so that suitable materials of construction can then be chosen.

Jan 1, 1962

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By C. E. Lesher

Two processes for agglomerating fine sized ores with low temperature coke are described. One process (Orcarb) agglomerates ores with limited amounts of carbon; the other (ore-carbon pellets) pelletizes fine sized ores, using low temperature cokes as the binder. Data are presented on the products obtained when taconite, magnetite, and hematite concentrates and several titanium oxide ores were used. Reduction of finely divided oxide ores has long been a major metallurgical problem. Various methods of agglomerating, notably briquetting, sintering, nodulizing, and pelletizing, have been developed and are in industrial use. Carbon is the usual reducing agent for oxide ores and attempts have been made to agglomerate fine ores with coking coal in order to get the metallurgical advantages of intimate contact and increased particle sizes suitable for subsequent smelting or reduction.

Oct 1, 1955

By E. H. Crabtree, T. C. King

The ferrosilicon grinding unit at the Central Mill of the Eagle-Picher Mining & Smelting Co. near Picher, Okla., was completed in March 1947. The object of the plant was to grind pigs of ferrosilicon, having a size of approximately 1½ by 4 by 12 in. and an analysis of 85. pct Fe and 15 pct Si, to approximately 100 mesh by crushing and wet grinding in a ball-mill classifier circuit. The minus-100 mesh ferrosilicon had formerly been purchased, and was used as medium in the heavy media process for treatment of lead-zinc ores. From the standpoint of dollars and cents, the cost of minus-100 mesh ferrosilicon was roughly $40.00 per ton more than pigs of the corresponding alloy delivered to the mill. Estimated wet grinding costs were considerably below this figure. The possible saving in cost of make-up medium for the cone plant was particularly attractive since, at that time, the plant losses averaged over four tons of minus-100 mesh ferrosilicon per day. Aside from the probable saving on the grinding charge, the need for such a unit was twofold. First, periodic fluctuations in the differential between the top and bottom densities of the cone were thought to be detrimental to metallurgy. There was little doubt that an intermediate differential existed at which the heavy media separa- tion was most efficient, representing a compromise between concentrate grade and tailing loss. Furthermore, if a finer, but considerably cleaner, medium could be obtained, there was the possibility that the differential could be decreased without increasing the viscosity, or conversely, the viscosity of the medium decreased without increasing the differential. Preliminary to experimental work aimed at pegging the cone differential and circulating medium viscosity at whatever values were found to be most efficient, it was essential to have control over both the nonmagnetic content of the medium and the particle size of the contained ferrosilicon. The latter was possible by means of a grinding unit at the mill. Second, whereas the ferrosilicon alloys are made by a number of manufacturers, only two, to our knowledge, grind it in any quantity for use in heavy media plants. For all practical purposes, the Central Mill was limited to one source of supply, a particularly vulnerable position. In case the supply was cut off, it was thought that pigs of the 85 pct Fe, 15 pct Si alloy could be obtained elsewhere, providing means of grinding them was available. There was no published information available covering wet grinding of ferrosilicon. Dry grinding in batch mills and in continuous mills with air classification was being practiced, but the cost of grinding was excessive and the dust condition objectionable. It appeared that primary and secondary crushing was no particular problem, providing heavy duty equipment was used;

Jan 1, 1949

By Sparrow GJ, Woodcock JT

A sample of pyrrhotite flotation concentrate pulp assaying 15.3 g/t An, which had been prepared from an old tailing dump, was treated to extract the gold. Examination of the concentrate with an SEM showed that exposed or free native gold, 5-40 ¦m in diameter, was present but no locked gold was observed. Direct cyanidation of the concentrate to extract the gold showed that the flotation reagents present inhibited gold extraction. A range of pre-treatments was used to overcome these effects.Direct cyanidation for 48 h extracted only 26% of the gold, indicating possible contamination of the gold in the concentrate with flotation reagents. Pre-treatment of the concentrate pulp by aeration for 24 h, or by 72 h aeration with an addition of 3.65 kg/t of sodium sulphite, gave little improvement in gold extraction by subsequent cyanidation. Pre-treatment by filtration, or by aeration with 12.5 L/t 100 volume hydrogen peroxide, followed by cyanidation for 48 h gave gold extractions in the range 67-77%. Combining filtration and an aeration period with hydrogen peroxide addition raised the subsequent cyanidation extraction of gold to 88%, giving a tailing assaying 1.5 g/t Au.

Jan 1, 1990

By L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes (Venkataramani, 2002). Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid startup and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate (Heberlein et al., 2007). Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates.Industrial plasmas can be broadly classified as thermal plasmas and non thermal plasmas. Thermal plasmas are atmospheric pressure plasmas characterized by local thermodynamic equilibrium (Boulos et al., 1994). Thermal plasmas are typically established between any two current conducting electrodes separated by an insulator. A plasma forming gas is blown between the two conducting electrodes resulting in a high temperature plasma plume. A plasma torch generates and maintains an electrically conducting gas column between the two electrodes; a cathode (negative electrode) and an anode (positive electrode) (Camacho, 1988). If both electrodes are housed in a single housing, resulting in an arc enclosed inside the plasma torch, then such plasma generating torches are termed as non-transferred (NT) plasma torches, whereas, if the second electrode is external to the torch, creating an arc transferred between the cathode and the working piece, then such plasma torches are termed as transferred (T) plasma torches. Depending on the source of the electricity which can be either direct current (DC), alternating current (AC) at main network frequency or at radio frequency (RF), the plasma torches are classified as DC, AC or RF plasma torches (Venkataramani, 2002)."

Jan 1, 2012

By Brechtel C. E

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kW (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1988

By P. N. Anyalebechi

The effects of solidification rate (0.4-26.1 K/s) and alloying elements on the cast microstructures of aluminum alloy 5182 have been investigated with directionally cooled laboratory-size ingots. The alloying elements examined included Mg (3.6-4.7 wt.%), Mn (0.35-0.75 wt.%), Fe (0.11- 0.42 wt.%), Cu (0.03-0.25 wt.%), and Si (0.11-0.28 wt.%). These reflect the chemical compositions of AA 5182 end stocks with high recycled used beverage container (UBC) content. For a given chemical composition, the average dendrite cell and constituent phase particle size decreased with increase in average solidification rate. In general, within the level investigated, Mg did not have a significant effect on the types, volume fractions, and average sizes of the constituent phase particles. However, increase in Mn, Si, Fe, and Cu increased average sizes and volume fractions of the constituent phase particles.

Jan 1, 2010

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By Noel N. Moebs

The U.S. Bureau of Mines is conducting research on many topics relating to the mineral resources of the United States. This is done to ensure an adequate supply of minerals essential to a viable domestic industry and a sound economy. The United States is almost totally dependent on foreign supplies for a number of minerals such as chromium, niobium, tantalum, and manganese for which there is no available substitute, while many other minerals such as titanium are abundantly distributed throughout the earth but seldom occur in adequate concentrations or useful forms. This report describes an example of a small but high-grade occurrence of titanium are in Nelson County, VA. This occurrence could be exploited under favorable economic conditions with new mining technology such as borehole slurry mining. The report demonstrates that the dikes at titanium ore, a mixture of ilmenite and apatite locally termed nelsonite, can be detected and traced along strike using magnetometer traverses. This information will aid in the selection of appropriate slurry borehole mining test sites in the area.

Jan 1, 1993

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The

By J. W. Harden

AT our meeting in October last we saw in operation at Pittsburgh, the comparatively modern process of the utilization of small coal by washing, by an arrangement similar to that of Bérard or Morrison. The small coal washed was that of an old pile, the refuse of the mining of the Pittsburgh bed, and which had long lain uncared for. Value was thereby restored to it when it was converted into a very good coke. This circumstance led to comments on the mountains of broken coal lying wasted, and in its present condition worse than useless, in the neighborhood of the mines of the Wyoming Valley, though they are not confined to that district. Some things were said condemning the course which produced it, some were left unsaid. Of a system that destroys one-half the coal-bed in producing the other half there can, however, be but one opinion. Schemes have been suggested for the utilization of present accumulations which, if successfully applied, would in so far be beneficial. More than ordinary attention is now being given to the same subject in England; a Mr. Barker has invented a means by which he amalgamates the "dust," too fine to burn in ordinary grates, with a composition he calls "diamond cement," producing blocks of coal said to resist water, both hot and cold, and which a smart blow will only break to pieces, not cause to crumble. But any scheme less than the one which will prevent the wasting of coal, which still goes on, though that involves the abandonment donment of the breaker, will only be one of expediency; and the latter can only be done by the aid of the consumer. But the wasting of coal is not alone with the breaker ; much is made in the mine. The cause is not far to seek ; the remedy is with capitalist and owner. Owners and consumers then are alike interested, and they have it in their power, in the one case, to mitigate, in the other, almost entirely to remove the cause of the evil. Of consumers there is one in every

Jan 1, 1873

By Xue Ping

Sm2Fe17 alloy is an important precursor for the preparation of Sm2Fe17Nx magnet, which possesses a higher Curie temperature, larger anisotropy field, better resistance to oxidation and thermal stability. In this paper, the wet chemical co-precipitation was developed for synthesis of the Sm-Fe alloy oxide precursor. Based on the principles of simultaneous equilibrium and mass balance, a series of thermodynamic equilibrium equations of Sm(III)-Fe(II)-NH3-C2O4 2--H2O system at ambient temperature were deduced theoretically and the thermodynamic diagrams of lg[M2+]T (M=Sm, Fe) versus pH at different solution compositions were drawn. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH value, reactant concentration, reaction temperature and aging time, etc. It is found that by precise control of the process, the Sm-Fe alloy oxide precursor was synthesized with fine crystallization and special size &size distribution.

Jan 1, 2008

The Colorado School of Mines, Golden, Colo. M F Coolbaugh, President. Since 1906 the School of Mines has issued a journal, known as the Quarterly of the Colorado School of Mines, which carries many articles on matters of general interest as well as other articles of a technical nature There is no regular subscription price to the School of Mines publications Anyone interested in back numbers should write and find out the conditions under which individual copies may be obtained, whether a price is set on them or whether they are free Some back numbers are not now available but efforts will be made to supply copies from the files of alumni or other friends of the School Vol 23, No. 3 of the Quarterly (July, 1928) is an index of the publications complete from July, 1906 to July, 1928. A selected list of the technical articles appearing in the Quarterly is given here: Vol 3, No. 3, Rare metals. uranium and vanadium, by H. Fleck (1909), vol 3, No 4, Tungsten in Colorado, by H R Van Wagenen, vol 4, No 3, Preliminary report of the radioactivity of the carnotite of southwest Colorado, by H Fleck and W. G Haldane (1909), vol. 8, No 1 (1913), Some recent developments at Leadville, by G. M Butler, vol 8, No. 3, Physiography of

Jan 1, 1933

By P J. Jacobs

FORACO is the third-largest global drilling services company, and recently celebrated its 50th anniversary. The company’s historical roots are in French-speaking West Africa, delivering hydrogeological drilling services to resource companies, villages and regional centres. Today, FORACO operates over 300 drill rigs in more than 20 countries.The Asia Pacific region of FORACO runs a fleet of 37 late model drilling rigs servicing the diamond drilling, reverse circulation, coal, coal seam gas and hydro drilling sectors.FORACO Australia has extensive experience delivering large diameter coring (LDC) samples to the resource community. In the past three years, the company has been involved in six 8? coring projects in a variety of geographies and geologies, including iron ore, coal and uranium. FORACO has developed proprietary equipment and techniques to deliver cost-effective LDC samples with outstanding core recovery.The FORACO LDC sampling system is hands free, with mechanised rod and corebarrel handing to minimise the risk of manual handling injuries. Sample volumes are six times PQ (the common industry standard for large core samples), with core recoveries consistently above 96 per cent in extremely difficult formations.Eight inch coring is a conventional coring system suited to hole depths up to 150 m. For deeper applications, FORACO has recently invested over $4 M in a 6? wireline coring system capable of achieving depths of 300 m.CITATION:Jacobs, P J, 2014. Large diameter core sampling, in Proceedings Sampling 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By J. R. O’Connor

Stimulated emission from Nd+3 in yttrium uanadate fYVOJ is reported. Single crystals of YVO4:Nd, obtained from Linde Col-p., have improved substantially in the last several months. Pulsed thresholds of YVO, laser rods are now approximately 2 to 3 5, cowparable to tliose for YAG:Nd. Yttrium uanadate crystalli~es irz a space group similar to zircon. All rare-earth vanadates have this structure. Rare-earth ions sucll as Nd+3 which substitutes for Y+3, aye situated irz a strong tetragonal crystal field which lacks inversion symmetry. This condition increases the p'robability of the parity-forbidden f — f transitions. Yttrium anadate has strong absorption bands beyond -1000A. These are clue to Y-O, V-O charge transfer and molecular transitions. Under 2537 and 3660A irradiation pure YVO, fluroresces u bright yel-LOLO. This fli&orescence is corrzpletely quenched in YV04:Ncl crystals. This and other evidence of energy trut~sjer from the lattice is repovted. Optzcul atz 1user pvope 1-ties o! YI'U4:E[t are brieJy described. THIS paper describes some of the optical and laser properties of Nd+3- and Eu+3-doped yttrium orthovana-date (YVO4). It reports laser action for the first time in this low-symmetry host. For some time we have pursued a research program concerning laser hosts' wherein the rare-earth (RE) ion is situated at a site of low crystal symmetry so as to increase the probability of radiative transitions. Single crystals of doped and undoped YV04 are grown from iridium crucibles in an oxyhydrogen gas-fired furnace by a modified Czochralski technique.' This material crystallizes in a D4li tetragonal space group of the zircon (ZrSiO,) type.3 All RE vanadates have the same structure and form solid solutions with YVO4. Therefore, it will be possible to investigate a variety of cross-pumped laser systems, as in the case of yttrium aluminum garnet (YAG).4 At present, ~d'~-doped YAG is one of the most efficient solid-state lasers.5 Accordingly, most of the material to follow will compare the properties of YV04 to those of YAG. Fig. 1 shows the relative transmission of YAG and two types of YVO4. "Pure" YVO4 has a normal absorption edge and is colorless. A second type has a broad absorption peaking near 4200A and is yellow. Rubin and Van uitert6 suggest the yellow material is slightly reduced. Samples of each type are being investigated by electron spin resonance,7 but these studies are so far inconclusive. The pulsed laser threshold is much lower in the yellow material than in the colorless. Therefore, the absorption at 3500 to 5000.4 transfers energy to the Ndi3 ions. Photons of wave length between 2000 and 4500A cause undoped YVO4 to fluoresce at 4800, 5250, 5460, 5540, and 5750A. This emission, previously reported by Brixner and Abramsom,8 is partially quenched by EU'~ and completely quenched by Ndt3 at room temperature due to energy transfer from the lattice to the RE ions. At low temperatures, some lattice fluorescence is present. This implies that the energy-transfer process is in part phonon-assisted. Although the YVO, single crystals used in this work were prepared from Y2O3 containing less than 0.01 pct rare-earth impurities, there is aopossibility that emission lines between 4800 and 5750A are due to dysprosium, terbium, and so forth. However, these lines are not observed in other compounds, prepared from Y2O3, such as YP04, Y2MoO6, and so forth. Furthermore, extensive absorption measurements on our "pure" YV04 single crystals between 0.4 and 5.0 failed to reveal any characteristic rare-earth lines. Fig. 2 compares the absorption spectra of Ndt3-doped YAG and YVO4from 0.6 to 1.0 . The Ndt3 absorptions are labeled according to free ion, R-S coupling. These term designationsQ are appropriate for YAG:Nd. They appear to be inappropriate for YV04:Nd. In YVO, neodymium must substitute for yttrium. The yttrium site is situated In a strong tetragonal field, where point symmetry is (42m) or possibly lower.1° However, the reduced splitting of the Stark components of the YV0,:Nd spectrum implies that the NdT3 ion is in a cubic site. The only plausible explanation for this discrepancy is that the Ndt3 ion is in a low-symmetry site, lacking inversion symmetry, so that a substantial admixture of 4f and 5d wave functions occurs. In this case, R-S coupling is not valid and J is no longer a good quantum number." Consistent with this view, the 4~ metastable level of YV04:Nd has an oscillator strength larger and a

Jan 1, 1968

Copper mineralization associated with minor molybdenum, silver, and gold occurs in a hydrothermally altered brecda within a granodiorite mass of Upper Permian age. A dyke system of rhyolite, dacite, and andesite forms plug-like bulges near the breccia and probably caused mineralization as a late stage effect.Base metal sulphides occur as disseminations, fracture and cavity fillings in the breccia. A pyritic halo in hydrothermally altered granodiorite surrounds the breccia and grades into unaltered granodiorite. Drilling during 1969 indicated the grade is subeconomic.

Jan 1, 1972

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006