Search Documents

By M. K. Aly

"ABSTRACTThis paper briefly describes the mining method proposed for the iron ore deposits in Wadi Shatti, western Libya. The iron ore produced will be used in the steel plant at Misurata on the Mediterranean coast. GeologyThe Wadi Shatti is located in the central part of western Libya. Flat iron-bearing sedimentary rocks are exposed with remarkable regularity in this valley. It occupies an area 200 km long by approximately 20 km wide trending in an eastnortheast direction between Jabal Fazzan in the north and Zel1af Sand Dunes in the south (Fig. I). Only a part of this valley has been ful1y explored by drilling on a 400- by 200-m pattern in an area of 18 km2 south of the town of Taroot. Farther to the south, no exploration by drilling can be done due to the presence of sand dunes .The iron-bearing bed is about 10to 15m thick, with a dip of 2 to 4 degrees in a southerly direction . The overburden consists mainly of clayey sandstones, 4 to 5 m thick, in the northern part, increasing to 35 m in the southern part. The iron ore bed consists of three different layers, from the floor upward: (1) Lower Reduced Ore (LRO), having a varying thickness of 1 to 7 m; (2) Magnetic Ore (MO), with a thickness varying from 4 to 12 m mainly in the central part of the area; and(3) Upper Reduced Ore (URO), with a bed thickness varying from 0 to 7 m."

Jan 1, 1980

By W. J. C. Pothas

This paper describes the state of the art in backfilling techniques used on East Driefontein Gold Mine. Areas covered are the preparation plant, the distribution plant, the pipeline network and finally placement techniques. The in-situ performance of placed backfill has been assessed by the Chamber of Mines Research Organization, and results to date will be shared. Details of the backfill expansion programme that will enable this facility to be made available to all working places are included. Benefits obtained by the introduction of backfilling are described, together with certain management aspects to be considered in the control of quality and quantity of support supplied via a pipeline.

Jan 1, 1988

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921

By Zhazira Baltabekova, Nina Lokhova, Arailym Dukembayeva, Madali Naimanbayev, Zhantore Dzhurkanov

"Recycling of industrial waste provided they have enough valuable elements requires significantly less investment compared with ore processing. Promising man-made raw material of rare earth elements (REE) is phosphogypsum. Works performed on dismantlement of phosphogypsum only concern phosphogypsum processing from apatit. In this case, none of the developments was tested for phosphogypsum produced on the basis of phosphorus, chemical and mineralogical composition of which is markedly different from apatites. We studied phosphorites of the Karatau deposits (Kazakhstan). Mineralogically all the layers are composed of three main ingredients: phosphate, silica and carbonate, which account for 92-96% of the weight composition of ores and rocks. Of impurities there are pyrite, iron hydroxides, gypsum, fluorite. In addition to the actual composition of phosphate in phosphate ores there are apatite. Silica is presented by chalcedony and quartz, and carbonate by calcite and dolomite. The results of X-ray microanalysis showed point cluster of grains containing REE in samples of phosphate ore. Analysis of the grain showed that REE are in the form of phosphates and silicates, which according to numerous studies in apatites is not established. In this regard, phosphogypsum, waste of production, is different in composition too. Therefore, transfer of techniques proposed in the methods for extracting REE from phosphogypsum after processing apatite, did not give the stated results and required a new approach to solving this problem. It should be noted that the phosphogypsum produced by processing the Karatau phosphorite contains medium group of REE by 2.6, and heavy group by 7.8 times more than phosphogypsum from processing the Kola apatite. Given the shortage of medium and heavy REE research to develop ways to extract the lanthanides from phosphogypsum after processing phosphate rock is promising. The study contains results of studies on the extraction of REE from phosphogypsum after Karatau phosphorite processing."

Jan 1, 2014

DAVID THOMAS 1871 R. W. RAYMOND 1872-1874 A. L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HUNT 1877 ECKLEY B. COXE 1878-1879 WILLIAM P. SHINN 1880 WILLIAM METCALF 1881 RICHARD P. ROTHWELL 1852 ROBERT W. HUNT 1883 JAMES C. BAYLES 1884-1855 ROBERT H. RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B. POTTER 1888 RICHARD PEARCE 1889 ABRAM S. HEWITT 1890 JOHN BIRKINBINE 1891-1892 H. D4. HOWE 1893 JOHN FRITZ 1894 J. D. WEEKS 1895 E. O. SPILSBURY 1896 THOMAS M. DROWN 1897 CHARLES KIRCHHOFF 1898

Jan 1, 1941

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By Richard Zamora

El presente trabajo describe la mineralización del fierro, cobre y oro en el distrito de Montaverde, Chile. El distrito Mantoverde está ubicado a 53 km al SE del puerto de Chañaral en la Cordillera de la Costa de la III Región de Atacama, Chile. La explotación minera del distrito se inició a principios del siglo pasado y continuó en forma irregular hasta que en 1989 la Empresa Minera de Mantos Blancos S.A. desarrolló los trabajos de exploración. Posteriormente, dichos trabajos a escala distrital permitieron ampliar el conocimiento de la mineralización hipógena e incrementar el potencial del yacimiento. En este sentido, el presente texto señala diversos antecedentes que ubican a Mantoverde como uno de los más importantes distritos cupríferos de la Cordillera de la Costa de Chile.

Apr 24, 2001

1 Healthy and active Local Section organizations are vital factors in promoting the vigor and growth of the Institute 2 Activity on the part of Local Sections should be recognized and stimulated by appropriation of funds from the Institute's treasury, and these appropriations should be as large as is consistent with the relative needs for other activities 3 As between different Sections, the amount of such appropriations should be based primarily on the extent of activities as reflected in the number and character of meetings held and the attendance of the members at such meetings 4 In making a request for funds for any year, the officers of a Local Section should submit a report on the printed form approved by the Directors at their meeting on November 19, 1937 5 A standing Committee on Local See-

Jan 1, 1952

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

not weaken. I saw him shortly before he was killed; his conduct under fire was splendid and an inspiration to his men. His loss is felt deeply by all ranks. Thanks to him and to others, who like him, paid the full measure of devotion to their country, our line was held until the critical situation in that vicinity was at an end. He died the true death of a soldier, with his face to the enemy. As we now look back, it is easy to believe that this holding of the line of defense intact by General Carey and his men was a determining factor in the outcome of the war. To have played so important and noble a part in this vital effort as that taken by Perry is assuredly the privilege of few. Our lives, it seems, are like capital entrusted to us to be expended as wisely and effectively as we may. With them we purchase whatever of accomplishment the stuff that is in us permits. It is impossible to escape profound regret that a career so full of the highest promise, and a personality so overflowing with all that is fine and lovable, should have been cut short at the age of thirty-one. Yet who can doubt that in a few months Perry bought with his life the fullest achievement of a life-time—a glorious part in the salvation of Liberty and Justice and Decency, indeed of Civilization itself! L. C. Graton.

Jan 1, 1920

By N. A. Ziegler

A certain amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautmanl published a paper in which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table I. Each alloy was forged in the ordinary way to All carbon determinations were performed by " Yensen " method. [N. A. Ziegler: Recent Developments in Analysis of Carbon in Iron and Iron Alloys. Trans. Amer. Electrochem. Soc. (1929) 56, 231.1

Jan 1, 1932

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Yi Wang, Xiaohui Fan

"The mineralization behaviors of typical fluxes are studied by investigating the microstructures with optical microscope. The results show that the reactions begin with between iron ore and lime, limestone with small particle to form primary liquid. Then coarse limestone, dolomite and serpentine take part in reaction under the action of primary liquid. Limestone is the easiest to mineralization, next dolomite, and the last is serpentine. The higher basicity and smaller fluxes size favor the mineralization process of dolomite and serpentine.IntroductionThe purposes of adding fluxes into sintering are that:(1) to increase the basicity of sinter, so as to reduce even eliminate addition fluxes into BF(blast furnace) and decrease the coke ratio of BF[1,2]. (2) to decrease the melting point of sintering mixture to ensure sintering can be carried out at a lower temperature and reduce the energy consumption. (3) to improve the qualities of sinter by forming binding phase with iron ore fines [3].Flux is another significant component for sinter besides iron ore, especially for high basicity sinter[4]. The proportion of flux is usually higher than 10% in sinter mixture(excluding return mine).There were many reports about the influence of the flux types on sintering, such as limestone, dolomite, lime and so on[5-7]. It is very important to choose suitable fluxes for iron ore sintering. Although the effect of flux size on sintering also has been researched, the mineralization behaviors of the fluxes in the sintering process has not been illuminated. The paper will study the mineralization behavior of fluxes in sintering."

Jan 1, 2011

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

The State of Western Australia has a land area of 2 525 000 km2, and is well endowed with minerals and petroleum products. In 1989 - 90 these products were valued at nearly A$10 500 million.

Jan 1, 1992

By Rafael Padilla

In the production of copper from chalcopyrite (CuFeS2) concentrates by the smelting and converting technology, the ambient pollution with gaseous S02 and toxic metals such as arsenic compounds is still a serious problem, especial1y in the converting step due to the batch nature of the conventional Peirce Smith process. Non-SO2 emitting alternatives are leaching processes. However, few of them have had a limited industrial application and they are not very effective in discarding safely the toxic impurities. A combination of pyro-hydrometal1urgical methods: the sulfidation of chalcopyrite and subsequent leaching of the sulfidized material is a non-polluting alternative to treat not only clean chalcopyrite concentrates but also complex chalcopyrite-enargite concentrates. In this article, this alternative is discussed concerning the thermodynamics and kinetics of the sulfidation of chalcopyrite with gaseous sulfur. The kinetics of the leaching of the sulfidized concentrate in an H2SO4-NaCI-O2 system is also discussed.

Jan 1, 2003