Search Documents

By W. Mostowitsh

I. Introductory LEAD sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. II. Decomposition of Lead Sulphate by Heat The dissociation of PbSO4 into PbO and S03 or S02 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumann1 found that PbSO4 was not affected by heat at 800° C.; that dissociation began at 900° C., and was rapid at 1,000° when the salt lost in 1 ½ hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbSO4 begins at 195° C., but progresses very slowly, with the formation of the basic salt 6PbO.5S03 at 705°; that this salt undergoes a transformation at 847°, begins to be decomposed at 888°, to sinter at 896°, and to fuse at 910°; rapid dissociation begins at 952°, and is accompanied by volatilization of PbO; retardations at 958° and 962° indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900° C. in 30 min. only 0.63 per cent. of its SO3, and that the loss increased with

Jan 5, 1916

By Donald R. Mason, Daniel F. O’Kane

DIFFERENTIAL thermal analysis measurements have been used to determine the ZnTe-In2Te3 pseudo-binary phase diagram. Since ZnTe and In2Te3 are both semiconductors, any intermediate compounds formed in this system should also be semiconductors according to the rules delineated by Mooser and pearson.1 The compound ZnIn2Te4 was first reported by Hahn et a1.2 and it has subsequently been prepared and characterized electrically by several workers. A brief summary of this work has been presented by Mason and O'Kane3 who also report that the compound appeared to melt peritec-tically. The Zn-Te phase diagram has been investigated by Kulwicki4 who found that ZnTe has a melting point of 1290° + 2°C. The In-Te diagram published in Hansen' contains significant errors, and has been redetermined by Grochowski et al.6 However, both sources agree that the melting point of In2Te3 is 667°C, with the latter authors reporting the previously observed solid-solid transformation occurring at about 550°C. Hahn ef al.2 reported lattice-parameter values for the ZnTe-In2Te3 system. The 67 mole pct ZnTe-33 mole pct In2Te3 composition was the only

Jan 1, 1965

By Yuuki Hagio, Hiroyuki Tobo, Michihiro Kuwayama, Yasutaka Ta

"Reduction of CO2 emission is necessary to remedy global warming, however, promising approaches of CO2 separation require a large amount of energy. Molten slag, which is generated as by-product of steel production, has high temperature, but its energy has not been harnessed. To recover the thermal energy from the slag and to apply to separation of CO2 are economical and environmental conscious ways. We propose a new heat recovery system, in which, molten slag is solidified continuously on water-cooled roll and the solidified slag plates are charged into counter-current heat recovery equipment. In laboratory scale experiments, heat recovery ratio of more than 30% was acchived by controlling the thickness of slag.IntroductionThe steel industry in Japan has been working on the projects of ""Environmentally Harmonized Steelmaking Process Technology Development (COURSE50)"". COURSE50 aims at developing technologies to reduce CO2 emissions by approximately 30%. One of the main technologies is to capture and recover CO2 from blast furnace gas using chemical absorbents to regenerate CO2-laden chemical absorbents by separating CO2 from the absorbents. As one of the solutions, JFE Steel Corporation has been developing sensible heat recovery process from steelmaking slag. It is effective to recover and use unutilized high temperature waste heat within a steel plant as the thermal energy required."

Jan 1, 2012

The first mention of gold in Western Australia was in 1848 when some specimens of copper ore, which are believed to have come from the Murchison district, were sent to Adelaide for assay. Gold was present in these specimens, but no particular interest seemed to be attached to this fact as the search at that time was mainly concentrated on base metals and coal. Interest appeared to be shown in gold in 1852 when several parties moved out eastwards from York looking for goldbearing country. Though these parties inmany cases were very near to what is now known as the Yilgarn Goldfield, nothing was found.The next record of gold was reported in some specimens which were brought in from Cardup, some 25 miles from Fremantle. Though this area was investigated, it would appear that all the gold had been contained in the specimens and nothing further was found, though the report had been the cause of a small rush of people interested in gold.From time to time specimens had been brought in by various people from the district east of Northam, and in 1861 a reward emanating from private sources was offered for the finding of gold within a radius of 150 miles from Perth. The Government at this stage took an interest in exploration for gold and in the same year supplemented this privately offered reward on a £ for £ basis. The Government also, about this time, commissioned a practical miner, with prospecting experience in the Eastern States, to examine the country between Albany and Northam with a view to the possible existence of goldbearing veins in that area. His report, however, was entirely unfavourable and nothing further was done. In 1873 a quartz lode was discovered near Albany arid a company was formed to work...

Jan 1, 1956

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015

By V. G. Papangelakis, G. P. Demopoulos

The high temperature (180-200 OC ) pressure oxidation (02 - HzSO4) process for the recovery of gold from refractory concentrates (FeS2/FeA8S) is simulated with the aid of a computer model. The model centers on the continuous operation of a multi-stage horizontal autoclave. In particular the effects of key process parameters controlling the autogenous operation of the autoclave are critically examined. The building elements of the model are (i) the continuous particle size distribution function of the concentrate, (ii) the residence time distribution function of the slurry and (iii) the shrinking core kinetics. Conversion is calculated on the basis of the segregated flow model. For the calculation of the particle size distribution at the exit of each compartment the population balance model is employed. The effects of feed rate, feed preheating, cooling, autoclave configuration and rate limiting regime (chemical reaction vs. gas-liquid mass transfer) on the autogenous steady state operation are discussed. Finally optimum reactor design and operation criteria are indicated.

Jan 1, 1990

By P. Somasundaran, R. D. Kulkarni

Reagentizing at elevated temperature, reported in the past as beneficial for the flotation of hematite using oleate, is studied here as a function of collector concentration, solution pH and ionic strength at various levels of conditioning temperature. The study revealed strong interactions between variables; particularly, the effect of conditioning temperature was found to strongly depend on the ionic strength of the solution. Thus, while an increase of conditioning temperature at lower ionic strengths or that of ionic strength at lower temperatures resulted in an increase of both flotation and grade, an increase of the former at higher ionic strength or that of the latter at higher temperatures caused a significant decrease in both responses. These observations have been explained in terms of the increased chemisorption of oleate at elevated temperatures and the temperature effect of ionic-strength on the salting out of the oleate from the bulk solution. The above effects which were first observed during Hallimond cell flotation tests were subsequently tested with Denver cell using low-grade iron ore. The results obtained using the two test procedures were in agreement with each other. The implications of these effects and interactions for process control of optimum flotation performance must be noted since variation in the levels of the above parameters are likely under plant conditions.

Jan 1, 1978

By M. E. Bell

The term "operational research" was probably first used to describe work started under E. C. Williams, now Director, SHAPE Air Defense Technical Center, late in 1937 or 1938, at the Bawdsey Research Station of the British Air Ministry, a laboratory center concerned with the development of radar equipment. After the practicability of the early techniques had been demonstrated, a large (for those days) program of development and installation was authorized. It was very soon realized, both by the Royal Air Force and by the scientists that almost as important as the gear itself was the way in which it should be used. Accordingly, it was decided that some scientists should cooperate to study the way in which the equipment should be deployed and operated in conjunction with the Royal Air Force. To distinguish this work from the normal work of a research and development establishment, the term "operational research" was coined. It merely meant at this time that this particular section of scientists was to be concerned with the use of the gear rather than with its technical development and it seemed natural to those concerned to adopt the word "operations" which has a specific connotation in the armed forces.' This method was later extended to peacetime business enterprise, government operations and other human activities. Operations research appears to have penetrated the extractive industries more slowly and less completely than other industries, the military, or the government. This may be due (1) to a difference in the attitude of management towards operations research, or towards research of any kind, for that matter; (2) to unsuitability of the extractive industries for application of the operations research method; (3) to inaccessibility of the data; (4) or to a lack of trained personnel who are interested in applying operations research to the mineral industries.

Jan 8, 1963

Mixers are commonly used for the transfer of oxygen in gas-liquid-solid reactions in minerals processing. The process rate is usually controlled by two steps: gas-liquid mass transfer and reaction kinetics. Some examples are described along with the factors used for analysis of the mass transfer design problem. Typical oxygen rates and appropriate types of aeration systems or mixers are reviewed. The commonly used Rushton turbine has limitations in a number of mineral processes. The development and characteristics of the LIGHTNIN A315 axial flow gas dispersion impeller are described. Some practical examples which highlight its advantages are briefly described.

Jan 1, 1992

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By J. Dehais, W. A. Wallace

The pressures of urbanization are forcing producers of construction minerals either to transport their product greater distances or find new mineral sources. In areas with significant urban development near the coastal zone, offshore resources may prove to be an economically attractive alternative source. This paper addresses the economic viability of offshore mining of fine mineral aggregate. It proposes a model using a mathematical programming formulation based upon past research on both the onshore construction aggregate industry and the coal industry. The model is then used to assess offshore mining economics in the greater New York metropolitan area. Results show that in this region total consumer cost would be reduced by offshore mining of fine aggregate. In addition, increasing economies of scale could be realized by progressively larger mining operations. The distribution of these savings is also discussed.

Jan 1, 1982

By B. Schimm

Mining of material without blasting and / or selectively becomes more and more important for high quality ROM-products. Surface Miners have been developed especially for this purpose. The cutting technology of these machines has been improved, so that harder material as well as wet and sticky materials can be cut with better results now. Especially the cutting drum design and more precise drum manufacturing process now allow production and equal tool wear over a long period. The better knowledge of rock parameters influencing the cuttability and cutting results allow higher production, less cutting tool wear and therefore reduced production costs.

Jan 1, 1999

By Thomas L. Vandergrift

The type and severity of coal mine entry failures are affected by the strength and stiffness properties of the roof, floor, end coal. Knowledge of the mine-wide trends of these properties Is valuable in developing effective ground control plans. Within the context of a larger effort to Improve entry stability In high horizontal stress fields, the U.S. Department of the Interior, Bureau of Mines, has evaluated three portable, on-site test devices to determine their suitability for identifying mine-wide physical property trends. The devices evaluated were the borehole shear tester, the Schmidt harmer, and the point load tester. Despite the lack of standardized data Interpretation procedures, each device provided useful on-site physical property data. The Schmidt homer was preferred for trend identification because of Its speed and simplicity. Schmidt hammer data were collected over a large area of an underground coal mine to compare calculated roof strength trends with a known geologic feature.

Jan 1, 1990

By Kadri Dagdelen

The classification of selective mining units (SMU) and the assignment of grades to those classified SMU are very important in open pit mining, especially for precious metal mining. When the classification is done, the true values of the SMU grades are unknown. These unknown SMU grades are mostly estimated analyzing the geologic data and blast hole assays. To classify the SMU's based on the estimate of SMU grade, without considering uncertainty associated with unknown SMU grade, yields incorrect decision in sending material to appropriate destination. In this paper, a method is developed to classify SMU's considering the uncertainty associated with unknown SMU grades. By using this method, traditional estimate of SMU grade is replaced with conditional probability distribution of SMU grade. The decisions about the destination of a given SMU are performed by minimizing the loss due to misclassification. Also, the asymmetric loss function by penalizing the overestimation and the underestimation unequally is used in assigning grades to classified SMU's. A case study is carried out to apply the traditional ore control techniques and proposed method in classification of SMU's and the assignment of the grades in a hypothetical gold mine.

Jan 1, 1999

The Australian mining industry faces skills shortages across a broad spectrum of disciplines and levels, as it enters another major growth phase. Critical amongst the areas of most significant shortage in the professional sphere is the discipline of geotechnical professionals. More mines, deeper mines, ageing workforces are all contributing to this chronic shortage. But the shortage is not just at the operating sites, it is across a range of employment fields including sites, head offices, consultants, researchers and educators. This paper reviews the status of a number of these fields and explores some of the issues being faced. The different roles of a site geotechnical professional and a specialist geotechnical consultant are explored, together with some of the trends in terms of how such people are operating, and the skills they are expected to have to fulfill their job requirements. The paper also considers the move towards possible mandatory statutory geotechnical positions at mine sites and some of the implications if this were to come into force. Finally, the paper considers the current provider programs for mining geotechnical education, and how additional offerings are going to be needed in order to address the current shortages and the inconsistencies in terms of job expectations for people assigned to geotechnical roles without adequate education and training.

Nov 25, 2010

By Johnson M. W

Factual data about the sedimentation in the Newcastle Coal. Measures are presented. Data concerning the total coal measure sequence (isopachs, sand /shale ratio and total coal thickness variation), data about three coal seams (Borehole, Dudley and Victoria Tunnel) and data about interseam con- glomerate units are discussed. From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin. The northern and north-eastern edge, which was unstable, suppl- ied most of the coarse detritus including the conglomerates to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern - each shows development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure. Evidence of in-situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.

Jan 1, 1969

By Godwin Beene

During recent years, copper and acid production from Nkana Smelter has formed a significant proportion of ZCCM's total output, but a number of problems affecting the smelter over the last decade have only been recently overcome. This paper discusses recent developments in the smelting practice, highlighting some of the operational problems experienced and associated solutions. The smelter performance over the decade is discussed and the innovations in the smelting technology employed to sustain production in the wake of limited re-capitalization are dealt with in detail.

Jan 1, 1999

The adoption of a plan of safeguarding American industry against extreme revolutionary industrial propaganda is the keynote of a report just issued by ex-Governor Robert P. Bass, of New Hampshire, covering the period of his service as. Director of the Marine and Dock Industrial Relations Division of the United States Shipping Board. He thinks that the only hope of America's resisting the tide of industrial unrest that is sweeping over the civilized world is in the development and early application of a constructive industrial program, in which program publicity and education carrried on by the Government will hold a leading place. He says: The Government should systematically inform both employers and employees in regard to many matters of the utmost interest and importance of each. It should acquaint labor with the Government's activities and service to labor in the past and should create in labor an appreciation of its joint interest with capital and with the Government in the problems of production. Satisfactory assurances should be given that labor will have a substantial voice in determining the distribution between capital and labor of the profits of production. Labor should be promised its reasonable share of any increase in production. There should be a joint determination of wages, hours, and conditions of work. Based on the foregoing principles, great emphasis should be placed on labor's interest and responsibility in the processes f production.

Jan 6, 1919

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By Fred C. Turin

The U.S. Bureau of Mines conducted a human factors analysis of hazards associated with roofholting activities in underground coal mines. Emphasis was placed on hazards related to the movement of the drill-head boom or mast of a roof bolting machine. The objective was to identify hazards and recommend solutions. The data-collection effort consisted of analysis of U.S. Mine Safety and Health Ad-ministration accident data; visits to underground mines and interviews with experienced roof bolting machine operators; discussions with roof bolting machine manufacturers; interviews with workers injured while performing roof bolting tasks; and reviews of research on roof bolting safety. A set of recommendations to increase the safety of roof bolting operations was developed. In particular, the following list of recommendations was presented in ranking order: (1) use an interlock device to cut off power to controls when an operator is out of position, (2) place fixed barriers at pinch points, (3) provide appropriate control guarding, (4) reduce fast-feed speed, (5) use automatic cutoff switches at pinch points, (6) redesign control bank to conform to accepted ergonomic principles, and (7) use resin insertion tools and resin cartridge retainers.

Jan 1, 2010