Search Documents

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

I.T.H. Drilling has been accepted as a tool used daily for both production and service work in Australian underground mines. For this reason, it is of interest to examine the rigs and drilling equipment in use to do this work, also to review the technique necessary to ensure that this drilling is done efficiently.

Jan 1, 1978

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

The Keweenaw Peninsula in the Upper Peninsula of Michigan is plagued with abandoned prospectors' test pits and mine shafts, the result of exploration and operation of mines for over 100 years. The Fort Wilkins State Park in Keweenaw County alone has three open prospectors' pits within its boundaries, protected by wooden fences and maintained by the (Michigan State Conservation Department as a tourist attraction.

Jan 1, 1967

By Eder Villarreal

Existen concesiones mineras en estado de prospección o exploración básica para las cuales, debido a que no cuentan con recursos o reserva mineral definidos, es muy difícil establecer un valor. La metodología que aquí se presenta muestra la forma de valorizar dichas concesiones mineras desde el punto de vista de costos y una serie de variables geológicas y económicas. El proceso consiste en calcular un costo base, realizar una evaluación cualitativa sobre la base de 10 variables, asignarle un peso a cada una de ellas y realizar una operación matemática utilizando dos ecuaciones.

Sep 20, 2019

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers' determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

ERRATA-AUTHOR'S REPLY IN SEPTEMBER, 1970, JOURNAL: PAGE 52 I. Left half of the page, 4th paragraph, fifth line from the bottom: for 22 / 5 1/2 %, read 22 / 5 1/2 %. 2. Right half of the page, fifth paragraph from the bottom, third line from the bottom: for N(l - p), read N(1 - p)x. 3. Right half of the page, fourth paragraph from the bottom, second line: for: at time t after time zero, read: at time x after time zero. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By Brown P. L

A study has been made of the geochemistry of the Ronneburg mine district as input to the overall management strategy for the rehabilitation of the mine site. The study drew on the geological data and information store developed over the 40 years of mineral exploration and mining at Ronneburg, and on chemical data from the literature which described the chemical processes of weathering, oxidation, dissolution and precipitation of minerals. The geochemical processes were divided into three groups based on their rate of reaction. Fast processes were assumed to proceed to equilibrium and were modelled using equilibrium chemistry equations; slow processes were assumed to be proceeding at a quasi-steady state rate and were modelled using chemical rate equations; very slow processes were assumed to have no role in describing the geochemistry for rehabilitation purposes.

Jan 1, 1995

By C. Pieper, J. B. Pateiro Fernandez, S. Möllerherm

"Since the United Nations conference on "environment and development" in Rio de Janeiro in 1992, the term "sustainable development" or short "sustainability" is used more and more in social-political discussions. Agenda 21 calls on the countries on national level as well as governmental and non-governmental organisations on international level to develop a concept of sustainability indicators to measure the progress towards sustainability. This paper deals with the development of an evaluation system for sustainability in the minerals extraction. By their application, aspects of sustainable development in the raw minerals industry are to be systematically conceived and assessed. This project has been carried out on behalf of the German Federal Ministry of Economics and Labour."

Jan 1, 2005

By R. Zunich, E. Rybinski, M. Grondin, B. Flintoff

It is uncommon these days to read a business magazine or newspaper without finding a reference to Knowledge Management (KM), and its critical importance to corporate success. One definition of KM is: “getting the right knowledge to the right people at the right time and helping them to put information into action in such ways that strive to improve organizational performance.” In the minerals processing industry we could assert that we have been practicing this for years through effective operator training. In most cases we would probably be wrong. Training has certainly filled the need of addressing safety and basic operational issues, but we must collectively focus on education (learning), and the difference, as measured in outcomes, is not at all subtle. This paper briefly examines the history of training and education in the mining industry, and looks in more detail at the impact of one company’s approach to empower its workforce, while keeping the ultimate goal clearly in mind: “The great end of knowledge is not knowledge, but action.” (T.H. Huxley)

Jan 1, 2001

By M. Andersson, R. Elsrud

The quality and the production rate for the mining operations in the Garpenberg mine has been much improved due to a new system, that presents the latest exploratory and planning data for the driller at the moment he deploys the drill rig at the face. Other components in this improvement work are better planning procedure, large-scale production system with longer rounds and introduction of new drill rigs in the mine. The new Rig Control System (RCS) for the new series Atlas Copco Boomers L2C has made it possible to develop this system for production drilling in the Garpenberg mine. The ABC Regular has been extended with map navigation and drill plan generator. The driller will have the best estimate of the orebody in front of him and the best drill plan for that orebody. The customer’s specific system will also become a standard Atlas Copco product for the Boomer ABC drill rig family.

Sep 1, 2001

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By T. T. Read

A SHORT time ago, one of the large steel companies courteously furnished the author with detailed records of the operations of a considerable number of iron blast furnaces over a period of two months. These will be made the basis of a subsequent study, but in beginning this study one of -the first points requiring consideration was the probable error of the records, for what otherwise might be regarded as significant differences of performance under different conditions were perhaps really due to errors of observation, or failure to observe and record variations. If it is assumed, in blast-furnace records and calculations, that known quantities or factors are constant, when as a matter of fact they are variable, the effects of these variations may erroneously be ascribed to some other cause. This is quite clearly expressed in the following quotation from E. Buckingham:1 Theory always operates on an ideally simplified picture of reality because real phenomena are unmanageably complicated. The results obtained are not exactly true for any, real phenomenon, though they may be for an ideal one; and the approxi¬mation with which a theoretical equation, however obtained, represents the actual facts, always depends on the approximation in essentials between the ideal picture and its real prototype. The purpose of dimensional reasoning is to find out how some quantity which is involved in the phenomenon under consideration is related to certain others; or to find the relation connecting two or more quantities which vary, or may vary, simulta-neously during the course of the phenomenon. Since we know that we must have a complete equation to start with, we begin by thinking the matter over, to see whether the quantities we have in mind are the only ones involved. Usually it is evident that they are not; so we next make a list of all the quantities we can think of which might under any circumstances be important. Upon considering this list, which is often a long one, it is usually evident that under the actual circumstances a number of these quantities may safely be ignored; so we cross them off the list and thus pass from our most general conception of the phenomenon to an ideal simpler one, in which these quantities are not involved at all.

Jan 3, 1925

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carried out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XO > 10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By Filmer AO

In contrast to the '50s and '60s, the period of the '80s and '90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world's R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration's Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration's request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing

By D. S. Dick

Over the last few years, new methods to characterize the flow properties of bulk solids have been developed. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field conditions. In addition, the effect of large particles on a material's flow properties (cohesive strength, bulk density, wall friction) can be determined as well as the effects of various additives such as Freeze Conditioning Agents. New developments have also taken place in terms of devices to improve the reliability of solids flow. Much attention has been paid to finding ways to provide a mass flow pattern with relatively shallow hopper walls through the use of inserts. Such devices can also provide reliable in-bin gravity blending of bulk solids and/or completely non-segregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. Many of these developments have direct application in the mining and minerals processing industries. Examples of each will be highlighted.

Jan 1, 1988

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969