Search Documents

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

By Robert H. Marshall

The application of simulation to production planning at a large, complex open-pit mining operation proved to be challenging and enlightening. The mine is divided into two separate pits and several dump areas which are served by the same truck fleet. The operating system consisted of shovels of two different sizes, wheel loaders, and a fleet of three different truck types moving material from seven source locations to ten dumping sites. The interconnecting haulroad network included many common segments. There were operating constraints unique to the system, such as: traffic rules; manpower limitations; shovel, material-type, and destination priorities and production limitations; and a unique, non-centralized dispatching method for truck distribution. The truck distribution was further constrained by the matching of trucks to shovels, loaders, and destinations by truck type. The gathering and transformation of input data as well as the evaluation of results and validation of the model were also challenging. Despite a high level of sophistication in production reporting, some input data were neither readily available nor backed by field observation. As a result, many innovative techniques had to be used to develop realistic input data and to validate the simulation results. Nevertheless, this case study definitely proved the feasibility of applying computer simulation techniques to short and long range mine planning and budgeting at a large, complex mining operation.

Jan 1, 1982

By Shihui L, Lianfu Z, Llanming J

The paper considers the essence of the multi-objective decision-making issues for selecting an optimal mining plan, and analyses the advantages and disadvantages of the multi-objective decision-making techniques commonly used for selecting an optimal mining plan. It presents the principle and practice of using a group-AHD with mixed factors to select an optimal plan.

Jan 1, 1995

By J. Richard Maier

Short-range mine planning (less than five years) previously was accomplished using contour and isopac maps, pencil and paper, an abacus, and our lucky quarter. Through the use of both micros and mainframe time sharing, Glenrock Coal Company (GCC) has been able to virtually put the old equipment away (except the problem solving quarter). In the process, GCC has saved many man-days and eliminated the more tedious parts of mine planning, such as picking elevations off a map with an engineer's scale and repetitive calculations. These savings have allowed GCC to do a more extensive job of mine planning as well as offer more alternatives, making GCC better prepared for possible economic changes. Mine planning, simply, involves looking at what has been done and deciding what needs to be done using various constraints. The application of this concept is not as easy as it sounds. The need for experience and insight cannot be replaced by a machine, but machines can supplement a person's ability by doing the bookkeeping and the repetitive work. Through the application of computers and their accessories, GCC has brought mine planning to a more modernized state. The following paper will detail the development and use of one system as used at GCC. Please note: In the figures and tables following, some of the data has been altered to protect confidential information used in mine planning.

Jan 1, 1983

NEW YORK MEETING PAGE Winchell, H. V.-Geology of Pachuca and El Oro, Mexico. Discussed by Frederick MacCoy, Robert Hawxhurst, Jr 2 WILKES-BARRE MEETING Kynor, Herbert D.-Mechanical Mining of Anthracite. Discussed by C. Evans, Jr., S. J. Jennings, W. J. Richards, Geo. S. Rice, and the author 3 Stein, C. H.-Ashley Planes for Handling Freight Traffic. Discussed by Graham Bright, Douglas Bunting, S. J. Jennings, R. V. Norris, C. H. Strange, Edwin Ludlow, W. J. Richards, and the author 3 Markle, Donald.-Anthracoal: A New Domestic and Metallurgical Fuel. Discussed by William Griffith, Edwin Ludlow, E. M. Chance, Charles Dorrance, E. W. Parker, G. H. Ashley, C. A. Burdick, Geo. S. Rice, and the author :.. 7 Griffen, John.-Slush Problem in Anthracite Preparation. Discussed by Henry Flood, Jr 11 Eavenson, H. N.-Lynch Plant of United States Coal and Coke Co. Discussed by E. V. d'Invilliers, C. Evans, Jr., Graham Bright, Geo. S. Rice, Geo. Otis Smith, A. M. Rodgers, C. T. Starr, C. A. Burdick, and the author 15 Bunting, Douglas.-Mine Fires Extinguished by Sealing. Discussed by Geo. S. Rice, J. B. Warriner, H. H. Otto, Edwin Ludlow, E. M. Chance, F. B. Nold, H. M. Chance, W. L. Jacobus, J. A. S. Ritson, R. D. Hall, Geo. S. Rice, and the author 18 Bright, Graham.-Determination of Electrical Equipment for a Mine Hoist. Discussed by F. L. Stone, Geo. S. Rice, L. F. Mitten, and the author 34

Jan 12, 1921

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983

By J. B. Reed, T. A. Read, H. Rosenthal

Although the season cracking of brass has been a subject of experimental investigation for more than thirty years, the mechanism that is responsible for this phenomenon is still obscure. While at- tempts to elucidate the stress-corrosion cracking of some alloys have been relatively successful, the principal accomplishments made in the studies of the season cracking of brass have consisted of improved techniques for the fabrication of articles of alpha brass, which reduce the danger of season-cracking failure in service. The primary purpose of the present paper is to collect the published experimental data which appear to be of importance to the development of an adequate theory of the mechanism of the season cracking of brass. Some of the possible mechanisms which have been proposed will also be discussed, together with some promising avenues of future attack on the problems. Several excellent survey papers on season cracking are available, including the recent ones by Croft and Sachs(1)2 and by Gibbs(2). The principal facts concerning season cracking, as presented in these papers, may be summarized as follows. The season cracking of alpha brass is a special type of stress-corrosion failure, which may occur in atmospheres containing ammonia, air, and water vapor. The stress causing failure may be either the

Jan 1, 1945

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By Walter E. Dean

Twenty six samples of carbonaceous gold ores and associated rocks from outcrop and mine localities in northcentral Nevada were analyzed for concentrations of major. minor, and trace elements, total sulfur, and organic carbon. Q-mode factor analysis was used to define six distinctive carbonate, organic, and detrital associations of elements, and to group samples based on these associations. The trace metals that have clearly enriched the organic-carbon-rich samples are V, Zn, Ni, Cu, Cr, and Mo, although few of the samples could be considered "metal-rich" when compared to other organic-carbon-rich black shales. Rock-Eval pyrolysis was used to evaluate thermal maturity and hydrocarbon yield of the samples. Unfortunately, most samples were too thermally altered to be suitable for routine organic geochemical characterization of organic matter. The 813C values of organic carbon in rocks from different deposits have a trimodal distribution, but there is no clear distinction between the three groups of deposits that can be related to age, thermal history, or depositional environment.

Jan 1, 1987

By Robert C. Freas, William H. Lane, David J. Krohn

Maysville, Kentucky, is the location of Dravo Lime company's new 9 070 mt(10,000 tons) per day limestone mine and 2 727 mt (3000 tons) per day calcination plant. This complex has been designed as a unit, and capitalizes on recent technological advances. Geologically the Dravo facility is.located on the eastern flank of the Cincinnati Arch, with the high calcium limestone being found at a depth of approximately 274 m (900 ft). A systems approach has been employed in designing and equipping the mine. This allows for maximum production while maintaining flexibility and versatility. All hydraulic drilling, large LHD equipment, and an extendable mine conveyor system are utilized in a five-part mining cycle. A modular concept modifies the room and pillar system to optimize ventilation. The limestone is calcined in three 5.18 x 61.87 m (17 x 203 ft) KVS rotary kilns with a design capacity of 909 mt (1000 tons) per day of lime per kiln. The kilns are coal fired and equipped with preheaters. Lime storage is provided by three 57 m (186 ft) high concrete silos with a combined capacity of 40 909 mt.

Jan 1, 1976

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

E. DEGOLYER,-New York, N. Y. (written discussion*).-Since the eastern part of the Gulf Coastal Plain is receiving considerable attention from various operators at the present time, it occurs to me that it brief review of most recent operations may be of interest in this connection, as well as a discussion of some of the points suggested by Mr. Hager. During the latter part of January, 1918, the Alahoma Oil Co. completed and abandoned a 3400-ft. (1036-m.) dry hole in Section 25, Township-8 North, Range 1 West. This well was drilled near the axis of the

Jan 4, 1918

By J. W. Evans

ONE of the most important and frequent calculations that the extractive metallurgist is called upon to make is that of the standard free energy change of a reaction (?F°). For many reactions of metallurgical interest, the lengthy arithmetical calculations have been eliminated by the use of free energy-temperature diagrams which have been constructed by Ellingham,1 Richardson and Jeffes,2 Kellogg,3 and Osborn4 (e.g., for oxides, sulphides, halides) from critical surveys of existing data. The speed and simplicity of making calculations with these graphs make them of great practical value and, this should be stressed, in the majority of cases no greater accuracy is obtained by the individual calculations from specific heat data, entropies, and heats of reaction. With the increasing industrial application of vacuum methods to the winning of metals, notably at present magnesium and the alkaline earth metals, it is necessary to calculate low metal vapor pressures above reaction mixtures. The existing free energy diagrams usually give values where the solid and liquid metals are at unit activity. To obtain the free energy change associated with the reaction Metal (solid or liquid) = Metal (gas) it is customary to calculate this from either vapor pressure equations or from the appropriate free energy functions. This paper presents graphically the free energies of vaporization of a number of metals of economic importance which can be used in conjunction with other free energy diagrams. Certain metals have been excluded on the following grounds: titanium, tungsten, molybdenum, and platinum have very high heats of vaporization and boiling points and the uncertainty of these values arising from difficulties of high temperature measurements makes free energy values of doubtful accuracy; the data for cobalt, vanadium, and zirconium are uncertain; finally, arsenic, antimony, and bismuth could not be conveniently included. because of the presence of mixtures of polyatomic and mona-tomic vapors in the temperature range considered. Free Energy Diagram In Fig. 1, the standard free energies of vaporization per mol (?F°T) have been plotted for the temperature range 0" to 2000°C for the reaction M (solid or liquid) = M (gas) The data have been obtained from the free energy functions — (F-H298)/T for the solid, liquid, and gaseous elements and the heats of vaporization at 298°K, i.e., ?H298 (vapor). The values of these functions have been taken without change from the recent critical survey by Brewer;' the bulk of this data is from Kelley7 with adjustments in the light of more recent work. Values of the function — (F-H298) /T at T = 298°, 500°, 1000°, 1500°, and 2000°K were employed. Where possible, a further independent value was obtained by using the boiling point, i.e., where ?F°T = 0. All calculations are based on the assumption that the metal vapors are monatomic and that the boiling points refer to those temperatures at which the partial pressure of the monatomic vapor above the metal is 760 mm. For the alkali metals, e.g., sodium, potassium, and lithium, diatomic gas molecules are present as minor species; details of these are discussed by Brewer." On the basis of the above values and allowing for the change in slope at the melting point, straight line graphs were constructed and extrapolated to 2000°C. The deviation from a straight line did not exceed ±500 cal, which in all cases appears less than the probable error in the ?F°T values.

Jan 1, 1954

By A. K. Isaac

The effectiveness of coalface powered support depends upon its structural nature and the manner of application of the hydraulic system. A critical and largely unresolved feature of the system is the optimum setting pressure level at which a support should operate in its geological environment. This paper provides an argument for a generalised approach to the issue of setting pressure level quoting case study data for a high output British longwall installation.

Jan 1, 1984

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

By Canterford JH

Current and future methods of data acquisition in hydrometallurgy are reviewed. Hydrometallurgical operations involve a wide range of chemical and physical processes for the recovery of metals and other products from ores and concentrates. Control of such operations requires information on the different liquid/solid and liquid/liquid mixtures being processed. Continuous. data acqui-sition for the liquid phases uses procedures already commercially exploited in other types of chemical plant. The major problem is the lack of robustness of measuring probes. Continuous analysis of the solid phases is much more difficult to-achieve because of the sampling and analytical techniques involved.

Jan 1, 1985

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995

By T. E. Wayland

The general geology and mineralogy of bentonite, including pertinent technological details of clay minerals in the montmorillonite group, are summarized. Worldwide occurrences of bentonite deposits are reviewed, with emphasis on geologic methods and economic principles of evaluation. Active mining districts are described and areas with potential for current and future development are assessed. The production history of bentonite, principal producers, major consumers, and indicated trends are noted; also attention is directed to the hundreds of minor industrial uses of this versatile material, ranging from the manufacture of (A)cid neutralizers to (Z)eolite water softeners. Recent significant results of both basic and applied research are reported, with suggested lines of investigation for current and near-future consideration.

Jan 1, 1972