Search Documents

By R. K. Young

Producing a sound plant design for a major project requires hundreds of engineers and many drawings. Economical accomplishment of this task is based upon careful and orderly organization of the design team so that at all times there is a complete and workable staff but at no time a surplus of costly talent. This paper will describe the various stages in the development of plant design which normally follow the laboratory and pilot plant investigations discussed in other papers today. An outline of the procedures used in the assembling of a project design group, within an established engineering organization will be presented. Actual procedures may vary according to the size and character of the plant, the special requirements of the owner, and the make-up of the engineering organization performing the design, but most of the points covered will be found to be basic to any plant design project.

Jan 1, 1960

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

The Peruvian mining industry has seen an explosion of foreign investment since President Albert? Fujimori's government was first elected in 1990. Since then, Peru has taken some large steps toward recovery, making it the envy of most other developing countries. A measure of political stability was gained in 1992 when Shining Path leader Abimael Guzman was captured. In addition, the country has taken on a huge privatization program, rewritten its foreign investment laws and has reined in its annual inflation rate from 1,700% in 1990 to about 8% by late 1997. Small wonder then that attendance at the XXIII Peruvian Institute of Mining Engineers conference reached a record level, many of whom are employed by some of the world's largest mining companies. About 2,700 mining industry professionals from all over the world attended the week-long event, held in late September in Arequipa. That was an increase from 1995s 1,600 attendees, that meeting also held in Arequipa.

Jan 1, 1998

By D. K. Uko

In the stretch-bend or bending-under-tension test, a strip is rigidly clamped and restrained at each end and bent by central transverse loading using a radiused punch: The strip deflection at failure has been used as a measure of formability for high-strength low-alloy (HSLA) steels by other investigators. In this work, a detailed study is made of strains developing during stretch bending of an 80,000-lbf/ in 2 (552 MPa) yield stress steel using different punch radii. It is shown that toward the end of the process, the bending strains at both the inner and outer surfaces are tensile and suddenly increase at a rapid and approximately equal rate. The strain ratio in the failure region departs significantly from plane strain , even using a large width-to-thickness ratio of about 10. The effective fracture strains appear to be independent of bend ratio (punch radius/thickness) and significantly below the fracture s train in simple tension. Metallographic and tensile data were obtained for the subject material and, for one bend ratio, the effects on stretch-bend parameters of annealing both on this material and a. carbon steel were compared.

Jan 1, 1977

By Jared Ball, Benjamin Hogg

There are over 100 process parameters that can be monitored during a single Peirce-Smith (PS) converter batch operation. To support a consistent operation it is important to select the correct Key Performance Indicators (KPI’s) to monitor. They should be strategically chosen to drive the desired behaviour with enough flexibility to endure process variations. At the Xstrata Copper Smelter in Mount Isa most of the PS converter operators have very little experience and are often lacking in the appropriate education or training to properly understand the process. For this reason 10 simple KPI’s were chosen that could be easily comprehended and monitored by all smelter personnel. KPI compliance has been supported by relevant project work in the converter area. Charge sequence trials have been performed in an effort to reduce splash and optimise activity time. The online measurement of full and empty ladle weights has enabled an immediate indication of skull size, skim/slag carryover, and metal loss.

Jan 1, 2009

By B Shen

The Wambo Rail Spur located near Singleton, New South Wales, Australia, runs for approximately 14 km linking the Mt Thorley rail loop and the Wambo Coal Mine. The project involves a 260 m long tunnel in weathered sedimentary and intrusive materials. The tunnel has a low cover and runs under a main highway. This second paper on the project looks into one aspect of the tunnel in detail: the use of shotcrete arch as the primary support for part of the tunnel excavation. The use of shotcrete instead of steel arch, formulation of the material specification, construction sequencing, installation at the excavated face and material testing for verification related to this facet of the project will be discussed in this paper. The tunnel opened in April 2006, and two years on, we briefly reflect on the impact of this design decision on the overall project.

Jan 1, 2008

By M. P. Smith, C. Hughes-Narborough, Y. T. Man

"Money and reputations can be lost in bad projects. Causes of bad mineral processing projects include poor contract definition and purchase of equipment without adequate test work. However, the root cause of many of the problems that can lead to bad projects is not any inanimate object, bad weather or catastrophic natural event but the people working on the projects. Because the people are so critical to the success of a mineral processing project, one must have suitably qualified and experienced people (SQEP) in all key positions. Characteristics that define SQEP include people who have successfully executed projects of similar size before; have undertaken projects treating the same minerals and producing the same valuable products and people who are familiar with designing, operating and implementing the required technologies and unit operations.To minimize the likelihood of future bad mineral processing projects, five recommendations are put forward in relation to the people aspect of a project.1. Attempt to retain SQEP during any down turn in the mining economic cycle so thatthe knowledge and experience can be kept within the industry.2. Increase the effort in attracting young people into the industry and retaining them.3. Set up robust training program to give young professionals a firm foundation of what real life projects and operations are like.4. Provide mentoring and continuous training for people after they have completed their formal graduate training program. Their career progression should be appropriately monitored and controlled.5. People working in projects must be exposed to as many detailed design and other finer issues as possible so that they can comprehend the amount of work required to deliver a project successfully."

Aug 1, 2016

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects'of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By Robert M. Becker

Particle mixtures were sampled in the laboratory, using ordinary sampling procedures, to determine whether or not the compound-multinomial probability distribution and other developments of part 2 agreed with experimental results. The objective was accomplished by the Bureau of Mines by comparing the moments and moment relationships of the appropriate probability models with their corresponding experimental values over a fairly wide range. The overall agreement between the corresponding theoretical and experimental values is both good and complete. The results demonstrate that sampling to a constant amount, such as weight, of items per sample is not the same, in general, as sampling to some constant number of items per sample. The results seem to confirm all the developments of part 2 and the application of the compound-multinomial function to bulk sampling.

Jan 1, 1965

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By E. Sengier

At the Director's dinner of the A.I.M.E. on. April 22, Mr. Sengier of the Union Minière du Haut Katanga was a guest. Though a member of the Institute for sev-eral years this was the first occasion on which he had had opportunity to meet with it, and in response to an invitation from President DeGolyer, after expressing his pleasure at being present, he told informally of the present development of the Congo with which he has been so closely related. From his remarks the follow-ing has been prepared.-EDITOR. AS you know, the Belgian Congo, a fairly large colony compared with the territory of Belgium, is in the center of Africa. Natural waterways, railroads now built and new railroads under construc-tion, give increasing means of transportation and are helping toward development. The mining industry is by far the most important part of our colonial activity. Considering that we are all engineers, I will confine my figures to mining enterprise. First I will show you the relative importance of the mining industry com-pared with the total exports of the Belgian Congo. During 1925 there was exported 100,000 tons of cop-per, valued at about $25,000,000; 900,000 carats of diamonds, 8000 lb. of gold, 1700 tons of cassiterite, 300 .tons of cobalt, and 20 grams of radium, of a total value of about $35,000,000. Other products to a value of about $12,000,000 and consisting mainly of palm nuts, palm oil, cotton, ivory, copal, rubber, were also exported. From this you will see that mineral products account for about 72 per cent of the total exported value. Copper alone amounts to 52 per cent of the total and 72 per cent of the mineral exports. All minerals, with the exception of gold, which is mined by the government, belong practically toy two mining companies in which American and British capi-tal is interested with Belgian. These two companies (one called Forminière, interested in the diamond busi-ness, and the other called the Union Minière, interested in copper, cobalt, tin and radium) were formed twenty-five years ago. They started producing in 1911, but the war prevented normal operations, and active de-velopment could only be carried on after the Armistice.

Jan 5, 1927

By Arthur Taggart

IN 1900, Elmore found that if an acidulated pulp was stirred up with an oil which was relatively insoluble in and lighter than water, and the mixture was al-lowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is two-fold, first to select the sulfide from the gangue-what to-day is called collection-and second, to buoy the col-lected sulfide away from the gangue. The action in collecting is illustrated by Fig. 1, which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids, we consider the oil and water fixed and the solids pre-sented to the surface of contact, the condition will be as shown in Fig. 2 ; the sulfide tends to be drawn into the interface and the gangue to be excluded. The sul-fide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them there.

Jan 6, 1928

By Craig Roberts

"While various methods are available to estimate a mining project's value, value is only established through a transaction. Comparable methods allow the value estimated for a mining project to be benchmarked against mining project values established in the market. Comparable methods thus are a key tool for ensuring value estimates are congruent with what the market would actually pay. For example, if the value estimated for a mining project using discounted cash flow analysis differs significantly from the value implied using comparable market methods, the valuator may be using metal price or discount rate assumptions that differ significantly from those the market is currently willing to pay for.The paper provides an overview of market comparable valuation approaches, and discusses some of the difficulties and limitations that arise in using these approaches. The types of market values that are typically utilised are discussed, including asset sale prices, share prices (market capitalisations), and values established in corporate mergers and acquisitions. Topics discussed include methods used in estimating a mining project's value based on the market value of the company that holds the asset, and limitations that arise because of unique features of mining projects and of companies that hold them.It is concluded that market comparable and fundamental (e.g. NPV) approaches to project valuation should not be viewed as alternative approaches to estimating project value, but rather can and should be integrated to derive a single value estimate based on both market andfandamental data. A method for integrating these approaches is discussed, and illustrated by example."

Jan 1, 2003

W. M. Courtis, Detroit, Mich. (communication to the Secretary) : Having made a rapid examination of the deposits described in this paper, I am not inclined to generalize confidently concerning its geological relations. But, since an analysis furnished by me has been included in the paper, it may be of further use to give the results of other samples and analyses. I give, therefore, a table of analyses by different parties, showing the average from surface-specimens:

Jan 1, 1901

By Dennis J. Lachel, Lloyd B. Underwood

In recent years a great number of papers have been presented at symposiums and have appeared in the literature relative to geologic prediction for rapid excavation and tunneling. Many of these papers describe research projects now underway to investigate tunnel site selection by remote sensing techniques, seismic holography, electro¬magnetic pulse sounding, optical scanning for structural features, and many other exotic geophysical techniques. While it is possible that this research will produce techniques that may prove to be very useful, it appears for the present at least, and perhaps for another decade, that there still will be no substitute for conventional exploration methods such as coring boring, geologic mapping, studies of existing wells, and proven geophysical techniques. Nevertheless, there is still room for tremendous improvement in the conventional techniques for geologic prediction in tunneling. These include: more rapid and accurately aligned coring borings drilled parallel to the tunnel alignment; improved geophysical surveys both prior and during construction; improved methods for predicting ground¬water inflows and water pressures, both of which can greatly influence the cost of driving tunnels. Geophysical techniques can also be ap¬plied to locate deeply incised glacial troughs or ancient buried stream channels that might cross the tunnel alignment. In the meantime, while some researchers continue their efforts to¬ward a breakthrough in new techniques for geologic prediction, it is recommended that other researchers direct their efforts toward sol¬ving specific problems such as accurately predicting ground-water conditions, determining locations of high geostatic stresses, and locations of major fault and shear zones.

Jan 1, 1997

A back-propagation model, which is typical of the models used in the science of artificial neural networks, was applied to the prediction of gossans from the southeast area of Habei Province in China. A success rate of 100 per cent was achieved. The results show that the neural-network approach is good, and that it can be used effectively in the prediction of multi metallic deposits.

Jan 1, 1995

By Hillary W. St. Clair

The effective coefficient for rate of reduction of a sample of granular iron ore may be determined by passing the reducing gas through a bed of the are at constant flow rate and periodically analyzing the effluent gas, The method of analyzing the data is based on a mathematical model that takes into account the variation in composition of the gas and solids with time and position in the bed. A method is described for determining the value of the rate coefficient that gives best agreement between the observed and calculated analyses of the effluent gas.

Jan 1, 1967

Underground mining and particularly dipping narrow tabular orebodies are difficult to mechanize appropriately, given the low gold price and other external factors. Particularly in the deep level mines in South Africa, there is little choice left but to mechanize if the industry is to remain competitive and a significant global player. This paper presents a design philosophy for appropriate mechanization intended to generate solutions that can be implemented using the people currently employed in South Africa mines. The design philosophy is based on the ability of high-pressure water (hydropower technology) to deliver enhanced performance to users and on simplicity in the eyes of the user. Four examples of systems and equipment are described to illustrate the approach to Appropriate Mechanization. These include: • The Development End System, • The Monorail Raise Climber, • Automatic Pump Control Valves, and • The Energy Recovery Pump. The equipment is presented with the following critical issues foremost in mind: Safety, Working Environment, Performance, Cost effectiveness and Implementation. Although the appropriate mechanization approach is described in the context of the South African underground mining industry, much of the Appropriate Mechanization equipment has worldwide applications. Key Words: Hydropower, Mechanization, Tunnel Development, Raise Development, Monorail, Raise Climber, Pump Control Valve, and Energy Recovery

Sep 1, 2001

By G. R. Hopkins

Crude-petroleum pipe lines in the United States on May 1, 1941, had a total length of 118,350 miles - an increase of 7,770 miles since Jun, 30, 1936, then the last previous survey was made by the Bureau of Mines. The expansion was due almost entirely to trunk-line construction, as the mileage of gathering lines was virtually unchanged from 1936. The greatest mileage of gathering lines, 53,640, was recorded in the survey of May 1, 1931. Both trunk and gathering-line mileage decreased moderately, in the interval from 1531 to 1936, but the present survey indicates that trunk-line facilities have expanded since 1936 to new high levels. Truck-line mileage equaled 55 percent of the total mileage of all crude lines on May 1, 1941, and 52 percent is 1936. The total length of gasoline pipe lines on May 1, 1941, was 9,001 miles this does not include several hundred miles of life under construction at that time or several hundred additional miles now being laid. No detailed surveys of gasoline mileage were made for 1, 1931, and June 30, 1936, but the mileage for those dates was about 1,400 and 4,600, respectively.

Jan 1, 1941