Search Documents

By N. A. D. Parlee, I. D. Shah, W. C. Phelps

THIS note reports on a continuation of a program on the thermodynamics of Fe-S-X systems in the "steel-burning" temperature range begun by Bock, Barloga, and parlee.' Small coils of 0.039-in.-diameter pure iron (Ferrovac-E) wire were equilibrated with Fe-S-0 melts in ingot iron crucibles under argon at 1324°C in the assembly shown in Fig. 1, the lower part of which was heated in a large Globar furnace. Fig. 1 shows (R) the coiled iron wire sample, (M) the Fe-S-0 melt prepared from desired proportions of ferrous sulfide and ferric oxide, (K) the iron crucible, (I) a mullite guide tube, (J) an alumina crucible, (L) alundum sand, (N) crushed mullite, (Q) hollow cylinders of K30 brick, (C) a steel rod, (B), (El, (F), (G), (P), and (O), details of brass water-cooled head, and (H) a mullite tube 2-3/4 in. ID and 26 in. long. The rod (C) bearing the sample could be removed at will and be replaced by a tube for sampling the melt, or by a thermocouple for comparing the melt temperature with a control thermocouple not far from the 2-3/4-in. mullite tube. After equilibration the iron coils were treated with acid to remove the outer layer of metal and then they were analyzed for sulfur by a standard combustion method. The melt samples were analyzed for oxygen by a variation of Lander's2 hydrogen-reduction method for mattes, and for sulfur by the ASTM combustion-iodometric method NO. E 30-47. When the results of some forty-two runs were examined it was found that the sulfur and oxygen contents of the equilibrated melts showed good consistency, in that the plotted compositions fell along the smooth curve shown in Fig. 2. The points on this curve represent the experimental compositions of melts in equilibrium with ?-iron (Fe-S-0) solid solutions. These solid solutions are saturated with sulfur and oxygen with respect to the melt and therefore have the same sulfur and oxygen activities as the melt. The curve drawn through the points therefore delineates the ? liquidus. It falls in such a position as to roughly confirm the liquidus curves of Hilty and crafts3 at 1200" and 1300°C which are

Jan 1, 1965

By R. Gehauf

Magnetic separation using rare earth rolls (RER) and rare earth drums (RED) have seem tremendous development and use in recent years. While the process of magnetic separation is understood, the principles affecting the separation, the specific application and the optimization of RERs and REDs are less well known. This paper offers practical insight into the basic operation, selection and optimization of RERs and REDs. It is a guide for the engineer who must design a test series and select the proper equipment for that application. It provides the engineers and line operators who control the daily operation of the equipment a basic understanding of the dynamics of operation and the principles that govern the optimization of RERs and REDs.

Jan 1, 2004

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre¬quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard. existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blasting, granite-cutting, or what not. Advancement to date in the United States in prevention and treatment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By W. D. Steele, S. D. Brady

The Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains minable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon-galia Co. thence south and southwest across the state to Wayne Co. near Hunt-ington. The Pittsburgh coal is also minable in the Upper Potomac region but is now practically exhausted there. The total minable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13¼ billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio River as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern West Virginia District comprising Wetzel, Mon-ongalia, Marion, Preston, Harrison, Dodd-ridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 1880 (when the Monongahela River Railroad, now B. & 0. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgan-town and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Mononga-hela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of minable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. Economic Importance The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1949

Report of the Americanization Society, New York Section During the past two months the Americanization Committee has held social meetings of various kinds for foreign-born women, as a preliminary to future effort along the lines of Americanization work. At the same time, a thorough investigation was made as to the work being done in New York by organizations devoted to this interest. The committee will be very glad to help any other committees being formed, in mining centers, with advice and information that has been gathered together as to classes and meetings of all kinds best suited to the needs of a foreign-born population. The work has been so extensively taken up in New York that for the present it would seem to be, for this committee, the most profitable and interesting work to continue the social meetings and to undertake the care of one or more immigrant families, to be friend and adviser in joy and sorrow, work and play, and in this way do some fundamental Americanization work. Respectfully submitted, LAURA G. BURGER, Chairman.

Jan 6, 1918

By Roy G. Stott, John A. Johnson, Floyd G. Anderson

"This information circular discusses drilling and blasting in open-cut iron-ore mines and is one of a series of papers describing iron-ore mining practices in the Lake Superior district to aid in preventing accidents in that industry.The Lake Superior district consists of the Marquette and Menominee ranges of Michigan, the Gogebic range of Michigan and Wisconsin, and the Vermilion, Mesabi, and Cuyuna range of Minnesota. Open-cut mines produce 8o percent of the iron ore mined in the district; 98 percent of the total Lake Superior district open-cut ore is produced in Minnesota and 2 percent in Michigan. The entire Wisconsin iron-ore production is from underground nines. The Mesabi range in Minnesota produced 93 percent of the open-cut iron ore and 76 percent of the total iron ore in the district in 1947.During the 8-year period 1940-47, 619,000,000 gross tons of iron ore were shipped from mines of the district, or 85 percent of the United States output. Approximately 78,000,000 gross tons of iron ore were shipped from the mines of Minnesota, Michigan, and Wisconsin in 1947.This paper is based primarily on observations daring the period July 1947 to March 1948. Thirty-two open-cut mines were visited; 28 on the Mesabi range, 3 on the Cuyuna range, and 1 on the Marquette range. In 1947, 36,100,000 tons of iron ore was shipped from these 32 mines, or 59 percent of the open-cut ore and 46 percent of the total iron ore shipped from the district. During 1947 about 90 open-cut iron-ore mines were operating in the district, and the annual production of each ranged from 25,000 to 10,000,000 tons.Many recommendations included in this paper for improving safety and preventing injuries to employees were taken from Bureau of Mines Information Circular 7387.Data were collected under the direction of Frank E. Cash, former supervising engineer, Health and Safety Division, Bureau of Nines, Duluth, Minnesota. E. W. Felegy, mining engineer, Safety Branch, gave valuable assistance in reviewing and editing the manuscript.The authors gratefully acknowledge the information and assistance given and the numerous courtesies extended to them by officials of the following mining companies:All the Lake Superior iron ores occur in bedded formations that range from less than 100 feet to over 2,000 feet in thickness. These formations are designated by one commonly applied name, ""iron formations.""4/The Mesabi range in northern Minnesota, about 70 miles northwest of Duluth, was opened to mining in 1892; it is the largest single source of iron ore in the United States. It is 75 miles long and, because of the gentle dip of the ore formation, it ranges in width from 1-1/2 to 3 miles.5/ The ore formation, which is nearly horizontal, has a maximum thickness of about 450 feet and is covered by a glacial drift that ranges from 10 to over 100 feet in thickness. Most of the ore is near the surface and adaptable to open-cut mining."

Mar 1, 1950

By Gieskieng, D. H.

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely different materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected

Jan 1, 1949

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Cindy Robles, Jose León Avalos

Poderosa es una empresa de mediana minería, socialmente responsable, con operaciones subterráneas, que explora, explota, procesa y comercializa recursos minerales con contenidos de oro, y comprometidos a: Mejorar continuamente el desempeño de nuestro sistema, Promover el comportamiento ético de nuestros colaboradores, Identi?car, comunicar y capacitar a nuestros colaboradores, Desarrollar el trabajo en equipo a través de los círculos de mejoramiento continuo (CMC) entre otras.

Sep 1, 2017

By Leonard L. Fischman

It is important to define "adequacy," and the most useful definition is a continuing availability of mineral materials under cost and other conditions which imply no significant burden on the achievement of otherwise attainable levels of consumption and well-being. For current decision making, it is sufficient to consider adequacy just to the end of the century, with some regard being given to then remaining mineral inventory. A comparison of cumulative demand projections to the year 2000 with already identified reserves ( economically recoverable amounts in known deposits) suggests little reason for concern with world adequacy of iron ore, aluminum, manganese, chromium or potash. Conservative estimates of "prospective" reserves (amounts producible at today's prices, but yet to be discovered) suggests that there are ample quantities of virtually all other mineral resources as well. A probable exception is oil and gas, of which there may be scant amounts remaining after the turn of the century. However, there is an evident sufficiency of substitute forms of energy, though it is difficult to see just where developing technology will take us. The critical questions have to do with the increasing dependence of the industrialized countries on external sources of supply , coupled with a new international politic s which complicates the problem of insuring timely development of, and access to, remaining deposits. In this context, Canada, a still mineral-rich nation, is in one of the more favorable positions.

Jan 1, 1977

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

Approximately forty years ago, the military services began a realistic investigation of the problems involved with the replacement of high pressure gaseous systems with liquid oxygen systems. The program was temporarily discontinued because of numerous State-of-the-Art problems. Ten years later, interest in the liquid oxygen breathing concept was revived. Initial testing of this concept was completed in 1946. The ensuing years have seen the general acceptance of many cryogenic breathing systems for airborne applications. The inherent features of weight savings (approximately 70%) and space savings (approximately 80%) make it very desirable for high performance military aircraft. A typical aircraft system consists of a storage container with appropriate integrated control valving (the liquid oxygen converter), a heat exchanger, breathing regulator, and oxygen mask. Normally the liquid converter is located in the aircraft wheel well for easy access by ground crew personnel and the breathing regulator is mounted in the cockpit where the pilot can connect his oxygen mask. An aircraft system such as this will provide the pilot with eight hours of breathing oxygen after a 24 hour standby period. Early in 1960, the National Aeronautics and Space Administration sought a means of providing a cooling system for their personnel involved in fueling the rockets used in the space program. While fueling rockets N.A,S.A, personnel wore a completely enclosed butyl rubber suit and were susceptible to heat prostration. Using the concept of an aircraft system, Aro redesigned the container, heat

Jan 1, 1971

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By A. M. Ghodgaonkar, P. J. Bhonde, R. D. Angal

Primarily ferrochrome is used to introduce chromium into steels and alloys. Chromium enhances hardness, hardenability, corrosion, abrasion and wear resistance of the steel. High carbon ferrochrome is one the cheapest sources of chromium, which finds large consumption in foundries and steel plants. However, carbon leads to problems viz. weld decay and sensitization of steels at elevated temperature causing catastrophic failure. Thus high carbon ferrochrome which otherwise enjoys financial edge over its low carbon grade is not suitable for final alloying or adjustment of chromium content. Subsequently, its addition burdens a steel maker. Hence, metallurgists around the globe have researched on finding out suitable technique for refining of ferrochrome. Traditional production methods of low carbon ferrochrome have drawbacks i.e. high refractory consumption, losses of chromium in slag and fumes etc-. Later these were overcome by adopting relatively new methods namely, metallothermic reduction, triplex process, vacuum technique to directly produce extra low carbon ferrochrome. Authors have carried SWOT analysis of the aforementioned techniques in the literature. Key Words: Ferrochrome, carbon content, low carbon grade, chromite, sensitization

Jan 1, 2007

By Fredrick L. Johnson

Tungsten is the principal mineral commodity in the Laurel-McGee RARE II area; copper and molybdenum would be recovered as by-products with the tungsten. Indicated and inferred tungsten marginal reserves at the Hard Point Mine (fig. l, no. 10) are 16,000 tons (14,000 t) averaging 1.0 percent tungsten trioxide (W03). The mine is outside the RARE II area, but the geologic structure that it is on extends into the area. Indicated subeconomic zinc, silver, copper, and lead resources at the Lucky Strike Prospect (fig. 1, no. 7) are nearly 6,200 tons (5,600 t) averaging 5.45 percent zinc, 0.5 oz silver per ton (19 g/t), 0.40 percent copper, and 0.32 percent lead. Although tungsten has been produced at the Tiptop Mine (fig. 1, no. 12), resources were not calculated because of the spotty nature of the tungsten mineralization. Additional exploration at the Tiptop and Hard Point Mines could reveal significant resources. The potential for tungsten resources at the Payday Prospect, Tungsten Prospect, and Morhardt Mine is also high. The Pine Creek Mine custom mill, located about 35 mi (56 km) southeast, could process tungsten concentrates from the area. Tungsten production has been recorded from three properties, the Hard Point, Morhardt, ant Tiptop Mines. Output was about 405,000 lb (184,000 kg) of W03, nearly all from the Hard Point.

Jan 1, 1983

By Henry O. Ash

On June 16, 1982, Rio Blanco submitted a request to the US Minerals Management Service for a suspension of operations under its federal oil shale lease. The company also wanted a five-year delay in the requirement for further minimum royalty payments and a five-year extension of the primary lease terms of 20 years. The request was granted in late July in the midst of yet another slump in oil shale activity. Rio Blanco holds one of four Federal oil shale leases that were granted under the Interior Department's Prototype Oil Shale Leasing Program in 1974. That year the DOI offered for lease six federal oil shale tracts, two each in Colorado, Utah, and Wyoming. The leases in Colorado and Utah were granted for substantial bo¬nus bids as shown in Table 1, but the Wyoming tracts had no takers. In the eight years hence, no oil shale has been produced commercially. Indeed, the prospects for successful oil shale development have fluctuated widely, continuing a 60-year- old cyclical pattern in the fledgling industry. The prototype program was developed and initiated while this infant industry struggled to begin anew, without the benefit of any federal oil shale leasing regulations, or any history of federal oil shale leasing at all. Permanent regulations were not required because the effort was limited and designed to provide the foundation for any future leasing program. Section 21 of the Mineral Leasing Act of 1920, a Nov. 30,1973 Federal Register notice, and the leases themselves constitute the legal and regulatory framework for leasing and developing prototype oil shale tracts. The prototype leases contain some unusual provisions including installment payments of the bonus bids, credit of early development costs against payments due the government, adjustment of royalty rates according to regional crude oil price fluctuations, and unusually extensive and detailed environmental stipulations. Several of the provisions were intended to provide incentives for early development and financial penalties for failure to develop. The requirement for minimum royalty payments in lieu of actual production royalties beginning in the sixth year of the lease falls in the latter category. After the sixth year, the required minimum payment is increased east year through the 15th year by an increment equal to that due in the sixth year. The minimum royalty then remains the same through the final five years of the primary lease term. Minimum royalty is calculates on a different production level for each prototype lease, based on the quantity of 125 L/t (30 gal/st) shale estimated to be recoverable from. each tract by room-and-pillar mining. That mining system was selected for reference as the only proven extraction method for oil shale at that time (early 1970s) The minimum royalty (production) rate was calculated for each tract by direct comparison of its estimated recoverable 125-L (30-gal) resource to a hypothetical tract containing 1.9 Gt (2.1 billion st) of recoverable 125-L (30-gal) shale. For the hypothetical lease tract, the minimum production for the sixth year was calculated to be 3.2 kt/d (3,500 stpd), increasing by a like amount each lease year through the 15th to a daily production rate of 31.7 kt (35,000 st). Under this formula, the hypothetical lease tract would yield $16 million in minimum royalty payments over the 20-year primary lease term if there were no production, no development credits taken, and no adjustment of the royalty rate due to fluctuation of regional crude oil prices. The production rate of 31.7 kt/d (35,000 stpd) was a somewhat arbitrary figure that was considered, in the early 1970s, to represent a minimum size for a commercial oil shale operation. A production rate of 7.9 dam3/d (50,000 bbls/day) soon supplanted that smaller mine production figure as a rule of thumb for the minimum size for a commercial facility. The proportional relation-

Jan 11, 1982

International Trade in Nonmetallic Minerals. BY J W FURNESS AND E W PEHRSON (Man &. Met, Sept, 432 2500 words) International trade in nonmetalic minerals (exclusive of fuels) is dominated largely by fertilizer raw materials such as phosphate rock, potash, nitrates, sulphur and pyrites and the miscellaneous group of minerals including asbestos, mica, graphite, fluorspar and china clay Cost of trans¬portation deters any substantial movement of the building materials which usually occur widely in nature and are thus available near consuming centers at relatively low cost This paper, which presents a summary for 1932 of the world production, consumption and principal trade relations of asbestos, china clay, fluorspar, graphite, gypsum, mica, phosphate rock and potash illustrated by world charts, is based on an original study of 15 nonmetallic minerals conducted by the U S Bureau of Mines Practical and Legal Aspects of Mme Financing See METAL MINING Economic Significance of High-grade Concentrates See MILLING AND CONCENTRATION

Jan 1, 1937

By Orville R. Lyons, A. C. Richardson

THE Coal Division of Battelle Memorial Institute, during the course of an investigation conducted for a coal producer, carried out extensive sampling of the fine-coal section of a preparation plant. The information obtained during the testing period was used to evaluate the overall plant operation and provided the basis for. recommended changes in the plant flowsheet. Included in the information were data for the results obtained when using a Bird centrifuge to dewater the particular coal being treated. At the completion of the investigation, the coal producer gave Battelle permission to publish the operating data for the Bird centrifuge in order to make this information available to the coal industry. The authors wish to take this opportunity to express their appreciation to this company and its officials for their willing cooperation in the matter of publication. Description of Preparation Plant: The preparation plant on which the data were obtained is primarily a jig plant. The coal being washed is a low inherent moisture, friable, Pocahontus-type. The washed coal from the jig is dewatered and sized at 1/4 in. by a Parrish-type dewatering and sizing screen. The minus 1/4-in. coal and the underflow water from the shaker screen flow to a sludge tank where, after the coal settles, the coal is conveyed by a flight conveyor into a pump sump. The pump, a 300-gpm sand pump, delivers a mixture of fine coal and water to a Bird centrifuge which produces a dewatered cake and an effluent. At the time when the investigation was made, the centrifuge effluent was returned to the sludge tank and the cake product was mixed with a coarser size of coal prior to loading into railroad cars. The semiclarified water from the sludge tank overflowed into a pump sump from which it was pumped to the jig. As originally designed, the preparation plant was intended to operate with a closed water system but it was found, soon after operations started, that for various reasons this could not be done. In order to provide for removal of excess water from the system and to aid in maintaining the desired minimum percentage of solids in the circulating water, the plant was operated to provide from the sludge tank a continuous overflow of water and fine solids that was sent to waste. The centrifuge feed represents approximately 35 tons per hour of minus 1/4-in. coal in the form of a pulp averaging 38 pct solids. Sampling Procedure: In order to obtain basic data for determining the relationships existing in the fine-coal section of the preparation plant, samples were obtained for: (1) the centrifuge feed, (2) the centrifuge cake, (3) the centrifuge effluent, and (4) the circulating water. The sampling was arranged to start on a Monday, in order to begin operations with a sludge tank full of fresh water, and was continued long enough to allow sufficient time for fine solids to build up within the water system or for a two-day, four-shift operating period. All samples were taken at half-hour intervals except when plant stoppages occurred. After a stoppage the plant was

Jan 1, 1951

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006