Search Documents

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Brij M. Moudgil

Separation of dolomite from apatite, because of nonselective adsorption, cannot be achieved by conventional froth flotation technique. Results obtained in the present study also indicate, that this can be attributed to the depletion of the collector molecules due to complexation with the calcium and magnesium ions, dissolved from the two minerals. However, it has been established in this investigation that conditioning the material at pH 10, followed by reconditioning, without any additional collector, at pH 4, results in selective flotation of dolomite from the mixture. The recovery of apatite, in the proposed reconditioning process, is much higher than with the conventional conditioning under similar pH conditions. The mechanisms involved in the conventional conditioning, and the reconditioning process are presented.

Jan 1, 1983

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By R. Altindag

The rock brittleness is one of the most important rock properties that affect the drill-ability of rocks. It is supposed that the increase in rock brittleness causes the increase in penetration rate. The drill-ability of rocks depends on many factors. These factors can be separated as two parts depending on a machine, bit type, rotational speed, thrust, blow frequency, flushing, and rock properties, brittleness, compressive strength, structure, hardness, etc. In this paper, the relationship between brittleness and drill-ability index, which is used in the prediction analysis of the penetration rate of rotary blast hole drills, were examined using regression analysis. It is also seen that significant correlations exist between brittleness and the drill-ability index.

Jan 1, 2002

By Vladimir S. Zharov, Vyacheslav A. Tsukerman

"Conceptual imitative dynamic model of developing enterprises for medium and long-term period permitting to ensure coordination of interests of the enterprise and territorial environmental authorities has been developed to enable the process of the prognostication and management of a concentrating mill development, in which a symbol language and terminology familiar to the manager of the company are applied. An algorithm of practical application of this model of company development was elaborated as well as a general methodological approach to the prognostication of the development and procedures of its implementation. The general methodological approach to the implementation of the model has been defined. Within the framework of system approach, a concentrating mill is considered as a subsystem of an ore mining and processing company or a mining and smelting one. A concentrating technology is considered in dynamics, its change is determined by the task of making the company operation profitable. Technological indicators are secondary relative to financial and economical indexes. At the same time, technological and economical indexes are determined in their interrelation with ecological parameters. The elaborated model allows us to estimate all necessary economic, financial and technological indexes in their interrelation both for the company as a whole and as separately redistributed estimating the basic prognostication documents - accounting balance-sheet, profit and loss report, as well as the funds flow statement. When varying the managing parameters, all necessary result-producing financial and economical indexes are estimated and a need in and a possibility of an external funding by various sources are considered.The implementation of the model enables one to determine the required scale of production capacity, as well as the amount of raw-material resources needed. In case of shortages of the latter, there should be considered various scenarios of the production capacity enhancement or the possibility of commissioning of new sites or deposits and introduction of improved technologies."

Jan 1, 2003

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the 'fine' and 'coarse' size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: > Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery > Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery > Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for fine, and 'coarse' particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2013

By W. W. Cutler

An oil-field drilling campaign is used in this paper to signify the spacing of the wells to be drilled as well as the drilling program, which is interpreted as the number of wells drilled in a unit of time, This has an important bearing upon the time of receiving income, as well as upon the amount of revenue obtained In periods of low prices for oil, such as the present, the margin of profit is at the best very small, and the correct determination of the drilling campaign may be the deciding factor between incurring financial loss or gain during the depressed period. General policy of the operator. Drilling should be planned by the field engineer to conform with the general policy of the operator. This policy may be one of conservation daring the early life of the property, but as mentioned later, this may result in a smaller ultimate recovery it often occurs that the market price of oil does not warrant rapid development, or it may be desirable to hold in reserve a supply of oil for a refinery. The policy may be to recover all of the oil as quickly as possible, or it may be to maintain a constant and sustained production. In any case, the operator should, outline as far as possible a definite policy, and should understand the principles underlying the recovery of oil, the influence of rapidity of drilling and effects of spacing, in order that he may obtain the oil as required with the least expenditure.

Jan 1, 1921

By Jerome P. Downey

In the thermal treatment of electric arc furnace (EAF) dusts, zinc is reduced, volatilized, and ultimately recovered either as liquid metal in a splash condenser or as solid zinc oxide in bag filters. During the process, the duet's chlorine and fluorine content also enters the gas phase and condenses as dross in the splash condenser or as salts which contaminate the zinc oxide product. Pretreatment of EAF dust by pyrohydrolysis appeared to offer a means of minimizing the duet's halogen content. The primary research objectives were to experimentally verify the technical viability of pyrohydrolysis and delineate the process parameters requisite for efficient halogen removal. To this end, representative EAF duet samples were secured and characterized by x-ray diffraction, scanning electron microscopy, and Mössbauer analyses. Specific- experimentation focused on the response of halogen extraction to variations in temperature, retention time, water vapor partial pressure, and various additives. The experimental results proved that 97 to 99 percent chlorine extraction and 80 to 85 percent fluorine extraction are consistently achieved when EAF dusts are blended with silica and roasted at temperatures of 850°C or greater in a furnace atmosphere of 75% steam (diluted by air). A statistical analysis further established that more than- a single optimal point exists, thus affording flexibility in parameter selection (e.g., by increasing temperature, the necessary retention time and additive concentrations are decreased). The findings substantiate the feasibility of pyrohydrolysis roasting in reducing the chlorine and fluorine in the EAF dust to a level that will obviate industrial concerns about halogen contamination. The end-product of the pyrohydrolysis procedure is a de-halogenated, self-fluxing calcine which can be directly charged to a plasma or flame reactor. The paper includes design parameters and flow diagrams illustrating the pyrohydrolysis process integrated with the plasma and flame reactor technologies.

Jan 1, 1992

By R. A. Mosser

Production control of aluminum content of low carbon aluminum killed open hearth steels is being achieved by using an oxygen probe unit. Based on the free oxygen content of the bath after block, a preliminary chart for aluminum additions has been established. The aluminum aim is .040%. Controlled aluminum contents will result in eliminating coarse grain heats, high aluminum contents, and a reduction in aluminum costs. By reducing the frequency of high aluminum contents both cleaner and better rolling heats will be obtained. The savings in aluminum costs is an added benefit of lesser importance in comparison to the quality improvements gained by controlled aluminum contents. Although the main goal for the oxygen probe at Republic Steel has been to adapt it for production control of aluminum contents, future usage could be extensive. Immediate plans for using the probe are on degassed material, on fully blocked open hearth heats to improve manganese recoveries and ranges, and on machining grades to control oxygen content. Also by controlling the oxygen content of the steel to as close to equilibrium conditions as possible, cleaner steel will result.

Jan 1, 1972

By Julius Pohlman

Considering the truly wonderful natural resources of the United States, and the variety and extent of uses for hydraulic cement at the present day, it seems strange that the manufacture of the artificial product called Portland cement has not been introduced here. Possibly the reason may be we have in different States of the Union rock deposits from which a cement can be obtained that is as good, and some claim even better, because of a more uniform quality, than the English product after it has been subjected to transportation across the ocean. One of these natural cement-rock deposits is found in the northern part of the city of Buffalo, and its manufacture has been carried on successfully for the past eleven years by the Buffalo Cement co., Mr. L. J. Bennett, President. The quarries cover an area of about two hundred acres, of which only twenty-five acres have been exhausted up to date; and the supply is assured for years to come. One acre yields on an average 80,000 barrels of cement; hence 12,000,000 barrels is a low estimate of what these quarries will yield before they are exhausted. According to the Geology of New York this cement-rock deposit is called the Water-Lime group, and forms in this section the uppermost member of the Upper Silurian. Its outcrop can be traced along the base of the second limestone terrace of Western New York, but at Buffalo a very large part of the overlying Corniferous limestone has been removed by natural agencies, leaving only about eight feet (six feet of rock and two feet of clay) on the top of the cement-rock, and thus furnishing the conditions for successful quarrying at a minimum expense. This rock is really an impure limestone, a mixture, as it were, of the underlying shales of the Onondaga Salt group with the overlying

Jan 1, 1889

By B. Tulu, D. Gearhart

A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia. Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry. Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation, stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site. During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading, while minor changes were detected in roof deformation. As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 30–50 ft of the instrumented locations. After reaching the peak loading at about two to three inches of roof sag, the cable bolts started to unload, and the load was transferred to the standing supports. The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed. The results were used to calibrate modeled cable bolt response to field data and to validate numerical modeling procedures that have been developed to evaluate entry support systems. It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location. The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.

Jan 1, 2017

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

The statistical methods described in the previous chapter permit the estimation of the average value p of a deposit, and the calculation of confidence limits for this value. They are based on the assumption of independence of sample values. As soon as a reasonable number of samples has been obtained from a deposit, local valuation, or estimation of blocks of ore within the mineral deposit, becomes necessary. The assumption of independence of values must then be rejected. Local valuation is possible only if there is a relationship between the value of a sample and the value of the surrounding ore, provided this relationship is a function of the position of the sample with respect to the blocks of ore to be valued. Whichever method is used for the valuation of a block of ore, the following assumptions are always made: ? The values of samples located near or inside the block are related to the value of the block. ? The values of the samples located closest to the block are most closely related to the value of the block. These assumptions will hold true only if the following assumption can also be made: ? There exists a relationship between sample values which is a function of the distance between samples. We are saying that the value x (z) of a sample centred at a point z has properties which are functions of this point. A certain spatial structure exists in the sample distribution. We are therefore dealing with a regionalized phenomenon, and we must treat x (z) as a regionalized variable. This can be done statistically by means of a model chosen to represent the spatial structure of the phenomenon. We shall see that the relationship between block values and sample values can be deduced from the relationship between sample values, and all local valuation problems can be solved using the statistical model obtained from the analysis of the sample values. It is important to realize that this statistical model is obtained by analysing the properties of known sample values, and will be used for the estimation of unknown block values. Such a statistical inference is valid only if the model developed represents the properties of both the sampled section of the ore body and the section to be valued: some stationarity conditions must be satisfied, and the model with the least restrictive conditions is preferred. In the following chapters, the most important models used in spatial geostatistics are presented. The models which can be used when there is no significant drift (trends) in values are described in Chapters 3-1 1. These models can also be used to solve some specific valuation problems when a linear drift is present. A general study of the more difficult problem of analysis of an ore body whose values present a drift is described in Chapter 12. Note that the area considered for local valuation of a block of ore is often small enough for any drift which might be present to be ignored.

Jan 1, 1978

By H. N. Maleki

Extensive measurements and underground observations in three Western U. S. coal mines are integrated in this paper to determine in-situ pillar load-deformation characteristics for narrow (30 it wide, 80 ft long) pillars in two-entry gate road systems. In spite of similarities in the regional geology, coal pillar laboratory mechanical properties and gate pillar geometries, the pillar peak strength, post-failure behavior, and failure mechanism were shown to be significantly different. Pillar peak strength was shown to be dependent on depth at one site, approaching burst-prone stress levels of 4000 psi. At another site, the pillar peak strength was lower because of lower confinement; this was related to the higher frequency of cleats and the lower friction- al properties of the roof/floor and coal contact. Two failure mechanisms were identified - one in the pillar, and the other in the mine floor. The roof stability was good at all three sites because of the thick-bedded nature of the roof strata and limited total gate span in a two-entry system. Existing pillar design techniques were shown to be inadequate for design, requiring adjustments for depth of cover, cleat frequency, and roof /floor frictional properties.

Jan 1, 1988

By M. G. Goudge

IT IS ENOOURAGING indeed to note during the past year that, despite a slackening off in many markets and with numerous major difficulties and problems to solve, the mining industry of Nova Scotia was maintained at a very high level. The value of the Province's mineral production for 1957 amounted to approximately $65,000,000. This represents a drop of only 1.5 per cent from the figure of the previous year. Coal Atlantic Collieries, Ltd., opened a new coal mine during the year at Bras d'Or. This colliery is equipped with the most modern type of mechanical equipment available, with transport of the ?coal by a belt-conveyor system. Other mines in the Province continued to mechanize their operations by the addition of Diesel haulage locomotives and other mechanized mining equipment. New wash plants are in operation and .an additional one is planned.

Jan 1, 1958

By G. A. Howes

This is one of a series of circulars dealing with the cost of equipping and developing mining properties in the United States and Canada, prepared and published by the Bureau of Mines in cooperation with various mining and exploration companies. This group of circulars is designed to supplement an earlier series which covered the methods and costs of mining and milling at a large number of producing properties. ACKNOWLEDGMENTS The authors desire to thank Robert A. Bryce, president of Macassa Mines (Ltd.), for permission to use the data presented in this paper, and to acknowledge the cooperation of A. J. Keast, under whose direction as manager the plant was installed and equipped and the shaft was sunk to a depth of approximately 2,000 feet.

Jan 1, 1932