Search Documents

By P. G. Van Der Walt

This paper deals with the reticulation of deslimed tailings from surface to the stope face underground. Reference is made to the experience gained at the pilot plants operating on four of the gold mines administered by Gold Fields of South Africa, as well as at the full-scale system at East Driefontein which was commissioned recently. Mine-wide backfill systems are currently being installed on five other mines administered by Gold Fields. These six full-scale systems are capable of handling more than 270 000 tons of backfill solids per month. The type of reticulation system chosen, the selection of flowrates and the composition of the slurry, as well as the selection of the appropriate pipes and ancillary equipment are discussed. Both theoretical and practical aspects are taken into consideration. Other aspects covered include the design of underground storage dams and communication systems.

Jan 1, 1988

By R. B. Snow

Inclusions revealed by the ultrasonic inspection of forgings, slabs, and blooms cause costly diversion or rejection of the product. Most of those inclusions are so large that they should have floated out of the liquid steel soon after teeming and been removed when the top discard was taken from the ingot. To investigate the source of the relatively large inclusions found in the body portions of ingots, a large forging ingot was examined from top to bottom along the centerline, and special studies were made of open-hearth and BOP ingots. A study of the inclusion distribution in the as-cast 134-inch-diameter forging ingot revealed only a few inclusions larger than 15 microns in the body of the ingot. Larger inclusions may be formed by entrapment of rising inclusions in large falling dendrites rather than by the precipitation and agglomeration of oxides from the liquid steel-dendrite interface during solidification. The original top crust of the ingot investigated broke away from the hot top and sank to the bottom during the solidification process, as indicated by entrapped inclusions found in a band 12-1/2 inches above the stool. A change in the hot-top insulation practice on subsequent ingots to insure the integrity of the top crust has produced clean ingots. A ZrO2 tracer was added to the hot-topping compound and to the top surface of open-hearth and BOP ingots after teeming. The tracer was found in large inclusions in slabs and blooms from these ingots. Large inclusions in the body of ingots appear to be related to disturbances of the natural freezing and shrinkage processes in the hot- top region of the ingot.

Jan 1, 1972

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Don M. Jackson, Robert W. Howard

Techniques for the epilaxial growth of single -crystal silicon carbide films on silicon were developed. The vapor-phase decomposition and bydrogen reduction of silicon tetrachloride (SiC14) and Propane (C3H8) resulted in clear films of silicon carbide, lip to seveval microns in thickness. The growth took place in a horizontal . silicon epilaxial reactor at 1100°C (pyrometer) at a rate of- 3000Å per minute. Electron diffraction and X-ray diffraction studies demonstrated that the films were single-cyrstal, ß -phase, or cubic silicon carbide. SiO2 film were used to mask areas of the silicon sur-lace in order that the silicon carbide might be grown in controlled geometries. Both n- and p-type films were grown on p-type silicon waters.. Heavily doped silicon films of the same conductivity type as the silicon carbide films were deposited over the silicon carbide in order to affect better probe contact to the structures. when n-type silicon carbide mesas were grown on p-type silicon substrates the de vollage-current relationships between films and substrates were that of junction diodes. These diodes showed a sensitivity to while light ill that the incident light increased forward- and reverse-satro,ation currents, P-type silicon carbide mesas grown on p-type silicon were ohmic rather than rectifying in their voltage -current relationship. No conclusions could he reached concerning heterojunc-tiou rectification in the structure. SILICON carbide is a semiconductor with many interesting properties. It decomposes at temperatures above 2200°C.1 It occurs in two general crys-tallographic forms—hexagonal (a Sic) and cubic (ß Sic)—with the cubic form having a forbidden-gap energy of 2.32 ev and the hexagonal form (specifically the 6H polytype) a gap energy of 2.86 ev.3 It behaves as an extrinsic semiconductor at temperatures approaching 5003C. It has been shown to have a high resistance to radiation damage4 and p-n junctions formed in Sic have been shown to radiate visible light under forward- or reverse-bias conditions. Epitaxial silicon carbide on silicon carbide has been successfully grown through the use of a variety of techniques, such as gaseous cracking of SiCL4 and CC4, nearly all of which require a deposition temperature above 1500°C.6 This paper will cover very recent work on the gas-phase deposition of highly ordered films of silicon carbide on high-quality silicon single-crystal substrates. The films have been shown to ex- hibit junction-rectification properties when geometrically isolated regions are electrically biased with reference to the silicon substrate. There will be no discussion of the mechanism of heterojunction rectification, but the methods of film fabrication, geometry control, and structural evaluations will be covered in detail. Electron diffraction, X-ray diffraction, and diode electrical properties were used to characterize the films and the junctions. GAS-PHASE DEPOSITION OF Sic The techniques for the deposition of silicon carbide films were a logical outgrowth of the standard silicon epitaxial process. The major premise followed was that, for any film to nucleate in an ordered fashion where there is considerable mismatch in lattice parameters (in this case 22 pct), an extremely clean, damage-free substrate surface must be presented to the gas stream. Thus a standard gas-phase HCl etching step was used to prepare the substrates for growth. A minimum of 5 µ of substrate-surface material was removed prior to the deposition of Sic overgrowth films. The techniques used for growing silicon carbide films were those of growing silicon alone, with the added injection of a hydrocarbon gas into the hydrogen and silicon tetrachloride gas stream. The hydrocarbon gases used thus far have been research-grade (99.99 pct) methane (CH4) and propane (C3H8). Propane ultimately gave the best results. The gas flows were controlled through a panel shown schematically in Fig. 1. A hydrogen main stream of 30 liters per min passed through the horizontal quartz-tube epitaxial reactor, while SiC14, C3H8, HC1, and doping gases were injected as side streams. The

Jan 1, 1965

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus, but those who have an economic interest have the following composition: Mn 29%, Fe 6% Si 5%, Al 3%, Ni 1.4%, Cu 1.3%, Co 0.25%, Na 1.5%, Ca 1.5%, Mg 0.5%, K 0.5%, Ti 0.2 0.2% and Ba 0.2% (Morgan, 2000; ISA, 2002). The Pacific Rim is an area of abundant occurrence of polymetallic nodules (Glasby et al., 1980; Morgan, 2000). According to these authors, the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000m (Morgan et al., 1993). In studies conducted in the EEZ of the Mexican Pacific are those made within the project "Research on the origin, process and distribution of minerals in the Pacific ocean floor in the Exclusive Economic Zone of Mexico". Within this project Rosales (1989) conducted studies on the origin, process and distribution of polymetallic nodules, finding that a number of processes give origin to nodules, being diagenesis one of the main mechanisms of elements that contribute to the nodules. Besides hydrothermal processes that are carried near the East Pacific Rise at 21° N, inputs are contributing to the nodules metallic elements and sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes occurs westward (Rosales and Carranza, 1990). In 1993, after cruise MIMAR II, Carranza and Rosales refer that metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba may have a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn).

Jan 1, 2011

By J. C. Sarace, S. M. Sze, C. R. Crowell

Thin films of tungsten 077 n-type germanium, silicon, and gallium arsenide were obtained by reacting tungsten hexafluoride with the semiconductor surface in an argom atmosplrere at temperatures between 325° and 400° C. Capacity-voltage, current-iloltage, and photoelectric measurements were used to investigate the characteristics of the tungsten -semiconductor diodes thus Produced. The junctions are shown to he very close to ideal Schottky barlp/ers with barrier heights measured with respect to the Fermi energy of 0.18, 0.65, and 0.78 1.1 jar W-Ge, W-Si, and W-GaAs, respectively. The electrical properties of the W-Si interface show no deterioration when heated to 1000°C in dry forming gas for 5 min. A theoretical value of the Richardson constant, A, appropriate to the semiconductor-hand structure has been used in evaluating the current-voltage characteristics. ThE W-Si surface-barrier diode was initially proposed for investigation because the eutectic temperature with silicon (1400°C) is much higher than that in the Si-Au system 1370°C).1 This would permit more flexibility in heat treatment and possibly provide greater reliability at elevated temperatures. The lower work function of tungsten (4.54 ev)2 compared with that of gold (4.78 ev)3 also suggested that a lower barrier height would be obtained with tungsten and hence a lower forward bias and lower minority carrier injection ratio for a given current density. The investigation was extended to include the characterization of W-Ge md W-GaAs surface-barrier diodes. The tungsten films have been produced by reacting WF6 with germanium, silicon, and GaAs surfaces in an argon atmosphere at temperatures from 300° to 500°C.4 This process is a very satisfactory alternative to the relatively difficult process of evaporating tungsten films in vacuo. To ensure an adequate electrical characterization of the tungsten-semiconductor interface, three types of barrier-height measurements have been performed. The mutually consistent results obtained lead to the conclusion that the tungsten-semiconductor junctions are indeed of the Schottky type. EXPERIMENTAL PROCEDURE The apparatus used for producing tungsten films is shown schematically in Fig. 1. It consists of an argon carrier gas line to which metered amounts of tungsten hexafluoride can be rapidly added. The mixture passes through a heated reaction tube containing the semiconductor slices and is exhausted to a hood. The argon is purified by passage through a 6-in. column of titanium turnings maintained at 800°C. The tungsten hexafluoride dispensing arrangement was designed by V. C. Garbarini and W. R. Bracht.4 A measured amount of liquid tungsten hexafluoride is injected into the argon stream and vaporizes. The mixture passes through a sodium fluoride absorption cell to remove traces of hydrogen fluoride, then into the nickel reaction tube. The tube is 12 in. long with an inside diameter of 1/2 in. The center section is heated by a furnace of the self-supporting wire-filament type. It was chosen for its rapid heatup and cooling. The wall thickness is 10 mils except for a 3-in. hot zone which is 30 mils thick to reduce thermal gradients along the length. The samples to be coated are placed on a sapphire plate and centered in this section. The tungsten is deposited with the following sequential steps: the loaded reaction tube is flushed with argon at a rate of 500 cu cm per min and heated to 370°C. Then 0.45 g of liquid tungsten hexafluoride is injected into the argon stream. The samples are held at this temperature for 2 min. The tube and samples are then cooled to room temperature and the samples removed. Tungsten films were grown on (111) faces of silicon and germanium polished with Linde A abrasive and lightly etched with HF-HNO3. The GaAs surfaces were (100) faces chemically polished with a H2SO4-H2O2 solution. The films have typical sheet resistances of 0.2, 8, and 15 52/0 when grown on germanium, silicon, and GaAs, respectively. After the tungsten deposition, ohmic contacts were alloyed on the back surfaces of the wafers. Ohmic contacts to the germanium and silicon were obtained by alloying Au-Sb at 370°C, ohmic con-

Jan 1, 1965

By N. Lilienberg

During the past fen- years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice mas to make steel ingots of suffciently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is " worked up," the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded, together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnauce and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory is, that the silver-clear blow-holes, without the blue oxide, can be welded by suffcient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the " blue " cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it " dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of the liquid interior after the surface of the ingot has become solid by contact with the mold. When this contraction is partly

Jan 1, 1907

By T. W. Hunter

THE TOTAL production of energy in the United States in 1954 decreased 4.6 percent below 1953. The production of coal continued to decline, and the production of crude oil decreased for the first time since 1949. These decreases were partly offset by an increase in the production of natural gas. The total energy production of 35,365 trillion B. t. u. in 1954 was the lowest since 1950. [ ] This drop in energy production was consistent with the 1.1-percent decline in gross national product during the year-from 364.5 billion dollars in 1953 to 360.5 billion in 1954.

Jan 1, 1958

By Don M. Coulter

"INTRODUCTION The district comprising Union, Lafayette, Pontotoc and Calhoun Counties, Miss. (fig. 1), was examined in October 1941 by R. W. Smith of the Bureau of Mines, accompanied by J. W. Adams of the Mississippi Bauxite Co. 3/ Subsequently, geologists of the Federal Geological Survey made a more detailed study of the area. 4/Bauxite had been reported as present in several localities in Pontot. County, and large deposits of kaolin are known in Pontotoc, Union, Calhoun, and Lafayette Counties. Many of the bauxite deposits, such as those on Big Hill, Second Hill, and Third Hill, in Pontotoc County, form the caps on hills and are outliers of Wilcox deposits on the Midway formation. Such deposits could have no extensions because of erosion and were not examined, as they were investigated by the Mississippi Geological Survey. 5/ Most of the bauxite was known to be low-grade, with a high iron content. However, Pontotoc County in particular presented possibilities of finding high-grade bauxite with a low iron content by drilling down the dip from the Wilcox-Midway contact. Consequently, with few exceptions the investigation was confined to drilling in this direction.Headquarters were established in Tupelo, Miss., on July 13, 1943, and mineral agreements were obtained covering 8,367 acres of land, with 62 land-owners in Pontotoc and Union Counties. Holes were drilled on properties of three of the landowners in Union County and 36 in Pontotoc County."

Apr 1, 1948

By B. Whitmoyer, J. Tian, J. E. Sneckenberger, M. A. Jerabek, C. A. Chandler

A computational procedure has been developed to determine the lung volume function for the upper airways of the human respiratory system. This analytical procedure computes a person's partial lung volume from an experimental two-microphone acoustic measurement of the upper airway passages obtained through a molded tubular mouthpiece. The theoretical transfer function for the two microphone signals as well as the related acoustic impedance and reflection coefficient for the upper airways are calculated using two-channel spectrum analysis techniques. An inverse spectrum analysis scheme then converts the reflection coefficient to an impulse response from which the airway area function is extracted using an area recovery algorithm. Numerical integration of the upper airway area function yields the lung volume function for the upper airways of the human respiratory sysytem. A software program to accomplish this computation of human upper airway volumes will be described in this paper. Application of this computational procedure to the measured tracheal acoustic impedances of 15 human subjects will illustrate the program's capability toward early detection of lung dysfunction using a prototype clinical facility.

Jan 1, 1991

By Watsford RMS, Wickham P

In October 1980 the two existing flotation circuits were combined into a single new circuit. This circuit used modern 11.3 m3 flotation cells which replaced 1.4 m3 units. Sometime after this change, a significant deterioration in metallurgical performance occurred. This paper describes the work done to discover the causes of deterioration in performance and actions taken. The program implemented to prevent a future occurrence is also presented. The work included analysis of routine plant data, analysis of surveys to obtain element and mineral flows on both a sized and unsized basis, some quantitative mineralogy, and analysis of some external factors.

Jan 1, 1978

By John J. Sammarco

The U.S. Bureau of Mines is conducting research into computer-assisted mining, which requires investigation of new techniques for development and application of computer-based technologies. Today's technology can require significant effort in software development, as has become evident in the early stages of this Bureau research. Technologies for software automation, such as computer-aided software engineering (CASE), are available. This report explores CASE, its general features, and its importance in software development. Information is presented to assist in selection and application of the variety of CASE tools and methods for automating various stages of software development. When evaluating CASE for use, it is important to examine tools that support an organization's existing methods of software development. Support for existing hardware platforms must also be examined. Merely selecting a "good" CASE tool does not insure success. Thorough evaluation of implementing CASE is also critical. Subjects to evaluate for CASE implementation include organization culture, support from management and end users, training resources, and pilot projects. Organizations that benefit the most from CASE evaluate CASE features with respect to their needs and they properly implement CASE.

Jan 1, 1990

By Krishna Nand

For assessing the safety of structures during underground explosions, ground particle velocity gives the best damage criteria, and 100 mm/see of ground particle velocity has been internationally accepted as the threshold value of safety (no damage). Results of extensive controlled underground explosion experiments conducted by the author to study the effects of ground vibrations on specially prepared concrete blocks, and also on low rise buildings and dams showed that no damage normally occurred when ground particle velocities were less than 100 mm/sec. Analysis of a large number of accelerograms from a dam site in India also indicated that no damage occurred to normal structures when integrated ground particle velocities were less than 100 mm/sec. Major damage in well built structures like a dam was noticed for ground particle velocity as high as about 350 mm/sec. These results are also generally substantiated from damage data obtained for various structures during other earthquakes, including Elcentro (1940), Taft (1952), Parkfield (1965), and San Fernando (1971). These studies, therefore, suggest that the damage criteria during underground explosions and earthquakes are similar; and 100 mm/see of ground particle velocity seems to be the general threshold value of safety (no damage) against ground vibrations.

Jan 1, 1988

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure of roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations and trial-and-error testing. Both the prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh, PA before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By Sakurai F

Akita Zinc Refinery of Mitsubishi Metal Corporation (MMC) started operation in 1953 with a capacity of 560 tons of electrolytic zinc per month. Its capacity has been expanded gradually and reached 8,100 tons per month in 1973. However, present production level is about 6,500 tons per month due to the depressed zinc market. In 1963, newly developed sulphate roasting was incorporated for residue treatment. Since 1973, electric power from Ohnuma geothermal power station of MMC has been supplied in addition to hydroelectric power from Komata power station of MMC. At present, about 40% of power is supplied from our company's power station and the rest is from the power company. Recent customers' demands for zinc prod- ucts include various kinds of shape, weight and chemical composition of galvanizing zinc alloy. It is necessary for zinc producer not only to meet the requirements of customers but also to enhance the value of zinc product in order to expand the market of zinc.

Jan 1, 1987

THE Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysicists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1944

By M. D. Hassiaslis

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1-The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2-The orientation of the chemical units at the surface; and 3-The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element-the mobility of the collector units in the two dimensions of the solid-liquid interface.

Jan 11, 1951

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D. O. Rausch

The economic relationship between steepening slopes and decreasing waste removal requirements ahead of ore mining is one of the most important factors in the design of open-pit mines. The steepness and stability of the pit slopes often spells the difference between ore and waste profit or loss in low cost open-pit operations. Unfortunately, the technology necessary for designing stable rock slopes is still in the early stages of development. Past and current pit-design methods have been, and still are, empirical, with rock slopes frequently made too steep or too shallow. As such, large expenditures are often made for correcting slopes after failures occur, or for unnecessarily removing more waste material than required.

Jan 6, 1965