Search Documents

Haematite Recovery from a Tailings Stream Laboratory and pilot scale testing were carried out in 1999 on a tailing sample from a North American iron ore plant using gravity, magnetic and flotation techniques. The ore contained 16 per cent iron mainly in the fine (-38 ¦m) size fraction. Two methods of evaluating the separation efficiency were used; Selectivity Index and Z factor analysis. Tabling and magnetic separation produced poor results, with flotation testing showing some promise, generating concentrates assaying more than 40 per cent Fe. High grade concentrates containing more than 67 per cent Fe were generated using the Kelsey Centrifugal Jig, and it was recommended that this technique be pursued at a larger scale to verify the results obtained.

Sep 13, 2010

By S. D. Van Nort

Editor’s note: This is the first of two MINING ENGINEERING articles about the Grasberg deposit. The second, focusing on open pit mine development, will appear in the April issue of the magazine. The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc. lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in the mid-1980s. Production at the open pit de- posit commenced in December 1989. The Grasberg copper-gold ore body is contained within a young igneous complex of dioritic composition that intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork. Irian Jaya comprises the western half of the island of New Guinea. The Ertsberg District lies 70 km (43 miles) inland from the Arafura Sea at an altitudeof3500 to45OOm (11,480to 14,764 ft). It straddles the Papuan fold belt. This belt forms the east-west trending chain of mountains that extend the entire length of New Guinea and is the site of numerous mineral districts.

Jan 1, 1991

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

By H. Para, A. Aguirre, G. Artadi

Mining is a very important economical activity in Peru which has been recently developed without considering environmental aspects. Here, we show an experience at the Milpo mine, situated 4,200 meters above sea level; a mining company that has the value of being one of few from the last decade that is engaged in consolidating a model of environmental protection. The model includes aspects of contamination prevention and control, with bioindicators such as pasture cultivation, vegetables, forests, and hydrobiological species breeding. Socially, through means of development programs in natural areas, forestation and support to rural agriculture, together with environmental education, it is being demonstrated that it is possible to ensure tangible results in environmental conservation and the well-being of the populations around the mine.

Jan 1, 1998

By H. A. Bourne, E. L. Haden, D. R. Reichmuth

A circumferential-toothed bit with novel tooth form gave improved penetration performance. In this design the exterior flank of all teeth were vertical when in rolling contact with the hole bottom. Rock chips were generated by the interior flank of the tooth displacing the rock inwardly and downslope toward the center of the hole. A unique two-cone laboratory bit assembly enabled evaluation of numerous cone and tooth configurations. Some of the variables investigated, in addition to weight on bit, rotary speed and rock type, were tooth interference, percent tooth, hole bottom angle, attack angle and relief angle. Most tests were conducted dry on a brittle synthetic sandsone or a ductile quarried limestone. Tooth configurations were found to be more significant in the ductile material. This was attributed to the deeper tooth penetration before rock failure. These studies showed that the attack angle (angle beween interior flank of the tooth and rock surface) was the controlling variable; changing the tooth configuration from the assymetric or semi-wedge to the more conventional symmetric or wedge form reduced penetration performance; and penetration performance of circumferential-type cutters was directly proportional to rotary speeds up to 200 rpm. INTRODUCTION Much of the published literature on rock-chisel interactions describe experiments wherein symmetrical wedges are vertically loaded or impacted against a smooth rock surface.1-6 are is usually taken to insure that the indentation is not made near the edge of the rock specimen less erroneous data be obtained. The literature describes relatively few studies in which the investigator deliberately attempted to take advantage of an edge or free surface. In contrast, anyone who chips ice or breaks up a concrete sidewalk almost always works near an edge. Chisel "indexing," which has been considered by some investigator1,2,6,7 makes limited application of an edge or free surface. Probably the best documented investigation into applying this idea to drilling was that of Drilling Research Inc. at Battelle Memorial Institute.' Their "annular wing" percussion bit consisted of paired asymmetric chisels oriented so as to produce and move chips to the center of the hole. They predicted that the lowest energy requirement for chip generation would be achieved with a stepped hole bottom having a median angle of 45" to the horizontal. Results from limited tests showed that approximately 50 percent of the rock fragments were large and semi-circular in shape, as would be expected by a chisel impact near an edge. The remaining 50 percent were fine chips produced by the chisels in re-establishing the steps or ledges. Initial penetration rates with this bit were high, but they rapidly decreased. This was the result of excessive tooth wear caused by the constant friction on the gauge surfaces. The basic idea — circumferentially placed asymmetric chisels — still appears to have merit. If the concept could be applied to a rolling cutter bit, two of the shortcomings of the fixed chisel design could be overcome: (1) reduction in tooth friction, and (2) greatly increased cutter surface. Adapting asymmetric chisels to cutters rolling on an inclined hole bottom is restricted by bit geometry. The basic elements of roller rock-bit construction prevents the practical attainment of a 45" hole bottom angle. Nonetheless, experimentally it was considered desirable to investigate the influence of hole bottom angle to at least 40". This paper describes the laboratory studies conducted in evaluating the circumferential-toothed roller cutter rock bit. EXPERIMENTAL APPARATUS AND PROCEDURE BIT ASSEMBLY The cost of constructing a sufficient number of conventional three-cone rock bits to investigate circumferential cutter performance was prohibitive. Instead, a novel two-cone laboratory assembly which used an external bearing system was designed and constructed. The external bearings made it possible to alter the journal bearing angles and thus allow a wide flexibility in cutter configuration. Fig. 1 shows the laboratory bit assembly, the various bearing mount plates and the appropriate roller cutters for drilling shallow holes having hole bottom angles of 0, 10, 20, 30 or 40". The bit was limited to a drilling depth of 1 1/2 in. at the gauge teeth and a hole diameter of 43/4 in. This more or less intermediate size bit was chosen because it gave a more realistic match between bit teeth and the rock than would a microbit. Also, the rock sample size required was convenient and easy to obtain. CIRCUMFERENTIAL CUTTERS The tooth configuration used in our initial studies is shown in the upper half of Fig. 2. All cutters used in this series had the same tooth form — 43" included tooth angle, 2" positive relief angle and a horizontal tooth flat width of 1/32 in. Each cone cuts alternate rows except for the gauge row. The row-to-row spacing in view was 1/4 in. Static loading tests conducted earlier with asymmetrical chisels had been used to establish this spacing. These tests showed energy requirements for chip production increasing rapidly as the distances to the edge increased beyond

The acoustic signals emitted from a laboratory-scale ball mill were used for the estimation of the comminution of two complex sulphide ores, viz. Merensky and UG2 ores from the Bushveld Igneous Complex in South Africa. The digital acoustic signals were transformed to power spectral densities that could be related to particle size distributions (-75 µm to 4000 µm) in the mill by use of continuum regression. This approach is more general than principal component regression methods or Kalman filtering used previously and resulted in significantly more accurate calibration in the case of the Merensky ore, where approximately 93.4% of the variance in the particle size distributions could be explained. With fewer data available, the variance in the particle size distributions in the UG2ore could be explained less accurately (82.4%), but still satisfactorily. In addition, smaller particle sizes (less than 300 µm) could be modelled more accurately in the case of the UG2 ore.

Jan 1, 2000

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By W Pytel

A special model of vertically loaded pillar behaviour is introduced to the general, multi-plate based, floor-pillar-roof system interaction analogue. This permitted analysing room-and-pillar mine systems in any geological conditions, including the effect of pillar elastic-plastic behaviour with strain softening. In the model, pillar instability is one of the important phenomenon, which may be expected to occur, and which the operator has to be prepared for. Thus the entire systemÆs safety is determined mainly by strong roof strata behaviour and therefore they have to be examined in actual stress-strain conditions utilising the appropriate strength theories. It was assumed that the so-called safety margin, representing the relation between load intensity and material strength, might serve as the basic indicator of possible roof instability development. Therefore, the safety margin may be estimated by comparing the actually computed components of stress-strain tensor with ultimate values characteristic for a given material determined in laboratory. In order to illustrate the effect of technological pillar size on roof strata stability, two different mining systems (methods of mining) in one of the æPolkowice-SieroszowiceÆ Mine districts was modelled using the finite element method formulated in three dimensions, assuming different materials within different rock mass strata, as well as a number of horizontal planes of discontinuity within the model.

Jan 1, 2003

By D. G. Westlake, U. F. Kocks

WHILE single crystals of most materials with cph lattice structure show essentially unlimited ductility, polycrystalline specimens of the same materials exhibit the entire range of ductilities. A difference between the ductility of single crystals and polycrystals may be associated with the special stress concentrations to be expected, for example, at the intersections of slip bands or twin lamellae with grain boundaries. Whether such stress concentrations prove catastrophic depends on the cleavage strength of the material, the size of the stress concentrations, and the speed with which they are formed. Thus, the ductility may vary in degree from material to material. Another possible reason for differences in ductility between single crystals and polycrystals is that a sufficient number of independent deformation modes must be available to insure compatibility between the macroscopic strains in neighboring grains.''2 This criterion is often taken to be a necessary condition for any polycrystal ductility whatsoever, not as one that determines different degrees of ductility; thus, a material with an insufficient number of independent deformation modes would have to be brittle as a polycrystal. The "sufficient number" is five if every grain is to accommodate arbitrary shape changes ("von Mises criterion "). We should like to argue that fewer than five independent modes may be sufficient to satisfy compatibility conditions; and that the internal stresses set up when the plastic strains are not compatible reach the theoretical fracture stress only after a significant amount of macroscopic strain has taken place which may vary in magnitude from case to case, allowing an influence on the degree of ductility. Experimental evidence for these statements is taken from the following review of the number of independent deformation modes observed in the various cph

Jan 1, 1968

By H. Carroll Weed

By caving a block into the workings of its open pit and using the block as an ore transfer, the Inspiration Consolidated Copper Co. has solved a transportation and sizing problem, making possible a great expansion of open-pit methods as applied to Inspiration ore- bodies.

Jan 9, 1953

By Edgar G. Hill

Much has been written and said recently about the methods used and materials and equipment employed in building the long tubes that criss-cross a great part of the United States, like the pattern of a spider's web. This paper will discuss the fundamentals of design of these lines from the economic as well as the engineering viewpoint, pointing out the effect of the volumes transported, and the load factor, on the unit costs of transportation, as well as the effects on costs of the character 01 the fluids the lines are called upon to handle. Generally speaking, crude-oil pipe lines carry oil from the producing fields to the refineries. Sometimes part of the journey is by pipe line to a coastal point and tank ships are employed for the rest of the trip. The main lines of directional flow of crude oil through pipe lines in the United States are shown on Fig. I, but this, of course, does not always show individual pipe lines. Basic Formula for Flow OF Crude Oil The laws governing the flow of crude oil through pipes are well known. The basic

Jan 1, 1942

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

THOSE who have had occ.asion to sample a mine not infrequently find that it is impossible to take their sample cuts at regular distances apart, owing to the ground being close timbered, a stope having been taken out, or some other cause. When such is the case a tedious calculation becomes necessary in order to obtain an accurate result. A conscientious man will make the tedious calculation, but one who is inclined to be lazy, or who does not recognize the importance of accuracy, or has not the time, may be satisfied with either the arithmetical or weighted arithmetical mean result.There are two main systems of taking samples when the cuts are taken-(l) at equal distances, (2) at unequal distances. When the samples are out at equal distances apart there are three methods of computing the assay value :-1 (a) By Arithmetical Mean. The sum of the values and sum of the widths are each divided by the total number of samples, in order to obtain the value and width respectively, no allowance being made for the relative widths arid values. The result isabsolutely inaccurate, and should never be used under any circumstances.1 (b) By Geometrical Mean. The assay widths ie, feet %, feet oz, inch dwt, &c, are added together and the sum of these is divided by the sum of the widths.

Jan 1, 1911

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By E. V. Manlapig, M. A. Hampton, M. E. Holuszko

Methanol treatment of ZnS particles has been found to remove slimes and facilitate flotation. The removal of slimes renders the ZnS surface more hydrophobic, resulting in an increase in the hydrophobic attractive force between the particle and bubble. Hallimond tube flotation, induction time measurement and particle-bubble force analysis with the atomic force microscope (AFM) was undertaken to link the beneficial effect of methanol treatment of ZnS particles to their increased floatability.

Jan 1, 2009

This paper will present a series of examples drawn for a number of Australian and international mining companies showing their recent attempts at optimisation of capital. The results will be compared, contrasted and discussed in the light of six factors that are considered crucial to any analysis of this subject. The factors are: ò the market availability of capital ò the corporate strategy and performance ò the capital structure appropriate to the corporate positioning within the industry ò the parties to the optimisation equation ò the measurement of success of optimisation The factors above are not mutually exclusive and are generally interdependent so their order above is of little consequence. Other papers presented at this conference will dwell in more depth on all these factors, therefore this paper shall focus only on the key elements of each factor. By way of summary this paper will also address the issue of the longevity of optimisation - is it temporary or long term.

Jan 1, 1991

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995