Search Documents

By C. S. Smith

The solubility of tantalum at 1100°C is 0.025 pct in pure copper, 1.2 pct with 20 pct Ni, and 2.7 pct with -30 pct Ni. The solubility decreases with temperature, and the alloys are precipitation hardenable. A 79/20/1 Cu-Ni-Ta alloy reaches maximum hardness after aging at about 750°C and, if cold worked, does not recrystal-lize below that temperature. The alloys have good tensile properties at moderately elevated temperatures and, since they can be hot and cold worked nearly as easily as cupronickel, they are suggested for service at temperatures above the usual limits for copper alloys. MASSIVE tantalum dissolves extremely slowly in copper-rich alloys, and tantalum powder forms refractory surface layers which prevent its solution unless special precautions are taken. After many trials, an 80 pit recovery was consistently obtained by using a mixture of a finely divided tantalum powder with two or three times its volume of potassium tantalum fluoride (K2TaF1,-melting point about 750°C) poured in a slow stream directly on to the surface of the molten copper alloy, so that each particle would remain coated with flux and be immediately and individually wetted by the molten metal. A 50-50 nickel-tantalum alloy has a melting point of about 1400°C and small lumps of it slowly but satisfactorily dissolve in molten copper-nickel alloys as does commerical "ferro-tantalum." The high affinity of tantalum for carbon makes it necessary to avoid carbonaceous crucibles. COPPER-TANTALUM ALLOYS Castings with good shrinkage resulted when 0.1 pct Ta or more was added to copper melted under charcoal and cast in air. Copper in two-pound melts to which 0.1, 0.15, and 0.2 pct Ta had been added retained residual amounts, by analysis, of 0.025, 0.023 and 0.026 pct, respectively. The solubility of tantalum in molten copper at about 1200 °C is therefore about 0.025 pct. The electrical conductivity of these three samples was 100.48, 100.00 and 100.20 pct IACS in the annealed condition, and 98.24, 97.98 and 98.08 in the cold-drawn condition. Wires 0.080 in. in diam withstood from thirteen to nineteen reversed bends after annealing for 30 min in hydrogen at 850°C and the metal was therefore completely deoxidized. The annealing temperature corresponding to 50 pct loss of work hardness in 1 hr in a strip cold rolled 77 pct reduction was 175C, compared to 230°C for equivalent undeoxidized material. It is unusual for a decrease of recrystallization temperature to result from an alloying addition, and the tantalum probably combines with and removes some minor impurity in the original copper that restrained its recrystalliza- tion. No difficulty whatever was encountered in hot or cold rolling or drawing these ingots, and were tantalum not so expensive it would make an excellent deoxidizer for copper. COPPER-NIcKEL-TANTALUM ALLOYS Studies were made of the solubility of tantalum in a large number of copper-rich alloys, but of these significant solubilities were found only in the case of an iron alloy (which, however, separated into two immiscible liquid layers) and alloys of copper and nickel, in which tantalum is freely soluble and which were found to have interesting properties. The latter alloys are the subject of U. S. Patent No. 2,430,306 (1947). They are not at present available commercially. The Ternary Constitution Diagram—The copper-rich corner of the constitution diagram was constructed on the basis of microscopic examination of samples of various composition and treatments. The alloys were hot rolled to 0.25 in. from castings 0.625 in. thick, then annealed for 1 hr at 1000°C, quenched, cold rolled to 0.10 in. and finally annealed for various periods of time at temperatures between 800" and 1100°C in a nonoxidizing atmosphere and quenched. When the solid-solubility limit had been transgressed, particles of a compound believed to be Ni2Ta*were

Jan 1, 1960

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

Chairman, MRS. JESSE SCOBEY The Foreign War Relief Committee closed its dispensary fund during the past month with a contribution to the American Fund for French Wounded of $1720.51, balance on hand, principal and interest, as a gift from the New York Section of the Woman's Auxiliary for pressing emergency dispensary work in France. The American Fund for French Wounded was authorized to cable this sun at once, in consideration of the fact that their existing dispensaries, including the one established by the New York Section at Briey, were in excellent condition, while their mobile dispensary fund was confronted by the most urgent need for work among the refugees now returning in pitiable condition and in great numbers to certain distressing centers. The committee sewing at Fund headquarters every week has had seven working days, with an enrollment of twenty: The average attendance was ten; largest attendance for any one day, thirteen; smallest attendance, eight. Interest in this activity is growing steadily and it is the intention of the committee to push the work vigorously for the next few weeks.

Jan 3, 1919

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017

By José S. Lazarte Delgado

Debido a que la variación del ángulo del talud en un solo grado equivale a la remoción de varios millones de toneladas de material estéril, se ha previsto que el diseño de taludes debe ser explotado y proyectado con seguridad. En este sentido, el presente texto evalúa la estabilidad de los taludes a través del sistema de estructuras geológicas y así modelar adecuadamente las condiciones de la masa rocosa y determinar los cálculos basados en las mecánica de rocas mediante técnicas estereográficas , como la determinación de la relación entre altura y ángulo del talud.

Nov 20, 1978

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

By William J., Coulter

IN the early days of Colorado mining, between 1880 and 1900, when Leadville, Kokomo, and Robinson were boom mining camps, the entire area around Climax for a matter of fifteen miles was overrun with prospectors, so the mineralized outcrop at Climax was not unknown. The principal interest in minerals during this period was in gold, silver, and lead, and since the Climax outcrop showed none of these it drew little attention. Geology played an important part in bringing prospectors to the very edge of the Climax deposit. The Mosquito fault, which crosses near the base of Bartlett Mountain, continues as an important geological structure, at least as far as Leadville some twelve miles distant, and at the base of Bartlett Mountain the vertical throw on the fault is estimated to be between 2000 and 5000 ft. The sedimentary beds known to the Leadville district are all present on Bartlett Mountain to the north of the Mosquito fault, which cuts them off abruptly, and exposes the Pre-Cambrian rocks that underlaid them, so the prospectors, who were searching for gold, silver, and lead in the sediments

Jan 1, 1946

By Jean Pool Pillihuaman Carmona

En los procesos de separación del material valioso y la ganga, se consume energía que representa un alto costo dentro del proceso productivo minero. Se estima que este costo equivale a un 35% del precio de venta del metal. Este alto consumo de energía es requerido en los procesos de chancado y molienda, durante los cuales se busca un alto grado de reducción, hasta lograr tamaños, cada vez más pequeños, que permitan conseguir la liberación del mineral valioso, para su posterior recuperación como concentrado. El presente trabajo tiene por objetivo investigar y cuantificar el posible efecto positivo en el costo de la energía involucrada, que se conseguiría al aplicar energía microondas. El ensayo se realizó en roca mineralizada de un pórfido de cobre-molibdeno proveniente de la mina Cerro Verde.

Sep 1, 2017

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

By W. E. Hess

At the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed.

Jan 2, 1955

By J Watt

The Hidden Valley Gold Project is located in a remote and mountainous area of the Morobe Province approximately 30 km south of the township of Bulolo and approximately 90 km south-southwest of the provincial capital, Lae. The Hidden Valley deposit was discovered in 1984 with the nearby Hamata and Kaveroi deposits discovered in 1987 and 1992 respectively. Reserves (Harmony, 2009) at these three deposits are 42.1 million tonnes of ore containing approximately 2.9 million ounces of gold and 45 million ounces of silver. A further 5.4 million ounces of gold and 84 million ounces of silver are in the resources category. The process plant is designed to treat 4.2 million tonnes per year of gold/silver ore extracted by open cut mining methods. Ore is classified into three ore types according to oxidation state: oxide, transition and primary. The silver to gold grade ratio is high for the Hidden Valley and Kaveroi ores, generally in the range 15 - 20:1, and much lower for Hamata, typically 1 - 2:1: Primary ore is the dominant ore type at Hidden Valley with sulfur grades up to about two per cent sulfur. Oxide and transition ores are more prevalent at the Hamata deposit, but its primary ore has up to five per cent sulfur grades. Variable ore types, particularly in the initial years of operation, high silver to gold ratios and limited plant site area, due to the challenging terrain, present the main processing challenges for this project. This paper describes the operating strategies and process development for the main areas of this circuit, highlighting selections of processes and equipment that achieve cost effective, yet flexible solutions to the treatment of ores from these deposits.

Jan 1, 2009

By Chen Xizhe

The caisson is adapted to the foundation of concentrated heavy building. As there are the flowing sand, boulder or cobble and other serious obstruction, the open caisson can't sink, the caisson can solve these problems easily. Especially for the stability of the neighour building, the merit of the caisson is outstanding. Therefore, there are the pier, the foundation of heavy instrument and the large water pumping station etc. using the caisson in China. This paper introduce several caissons and successful experience by author's investigation. It contains the feature and application of the caisson : the examples of caissons such as a huge pier of a bridge acrossing a big river, a large instrument foundation and a large water pump station beside a river; the problem of the design of the caisson and notice items during the caisson construction etc.

Jan 1, 1991

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014

By Donald L. Meredith, Jeffrey Harris, Donald A. Stanley

Principal Components Analysis (PCA) is a versatile, multivariate statistical method that the Bureau of Mines is applying to mineral processing data to achieve data simplification and pattern recognition. The principal components are obtained from an eigenanalysis of the data matrix. To achieve data simplification PCA replaces a larger number of measured variables with a smaller set of principal components and at the same time removes a significant amount of experimental error. Data simplification and error reduction make PCA useful in process control. Plots of the individual principal components form the basis of a pattern recognition technique that allows detection of significant variations in the structure of the data. These applications of PCA are illustrated with appropriate mineral processing data.

Jan 1, 1993

By E. Rupprecht, J. Volkwein, K. Cashdollar, R. Gürtunca

The National Institute for Occupational Safety and Health (NIOSH) mining research program at the Pittsburgh Research Laboratory (PRL), includes the areas of coal mine dust control and monitoring, and explosion prevention. One very important project at PRL is development of a continuous recording person-wearable respirable dust monitor. This Personal Dust Monitor (PDM) is a respirable dust sampler and gravimetric -equivalent analysis instrument that is part of a belt-worn mine cap lamp battery unit. Prototypes were successfully tested in the laboratory and in four underground coal mines. The PDM testing demonstrated that it was convenient to wear and use, robust, and provided accurate and timely data. NOSH is also conducting research in the program area of coal mine explosion prevention, suppression, and mitigation. Aspects of this research program include: full scale explosion research, laboratory scale research, frictional ignition of methane, mine ventilation seal construction, prediction of coal mine methane emissions, mine monitoring systems, flame cutting and welding operations, spontaneous combustion, and emergency preparedness.

By T. A. Apelt, B. J. Elliot

"In September 1993, the flash furnace at Kalgoorlie Nickel Smelter, KNS, was brought off line after almost 12 years of operation. This is a record campaign life for a flash furnace. The furnace was' totally rebuilt and the capacity of the plant increased from 540 000 tpo to 750 000 tpa of concentrate throughput. The throughput increase was' achieved through the construction of a 525 t/day oxygen plant and upgrading of various plant ancillaries. A number of significant design modifications were also built into the flash furnace and oxygen enrichment was implemented in the operation of the Peirce-Smith converters.This paper discusses the rebuilding of the flash furnace and design modifications made to furnace equipment and ancillary plant. Some preliminary post-startup operating data are presented.IntroductionIn September 1993, Campaign 6 of the flash furnace was concluded and the furnace brought off line for rebuilding. The campaign length was almost 12 years and set a new record for campaign length. Planning for the rebuild took place over the last five years of the campaign. A number of modifications to the design of the furnace and the ancillary plant were planned to coincide with the furnace rebuild. The furnace was rebuilt and recommissioned in 70 days. The increased plant capacity of 750000 tpa has been achieved by the construction of a 525 t/day oxygen plant and modifications made to ancillary plant which centred around increased p~ control, efficiency and hygiene. This paper examines the development and implementation of the modifications made to the furnace and ancillary plant. Preliminary post-shutdown performance data are presented."

Jan 1, 1995

This paper covers only the energy uses of natural resources and does not deal with non- energy uses, which in 1975 were of the order of 10 per cent of the total consumption of energy resources. The United Nations `J' Series of Statistics ex- presses each of the various forms of energy in terms of its coal equivalent in metric tonnes and this basis is followed in this paper. One tonne of black coal (referred to as tce) has been taken as the equivalent of the following. 29 X 109 joules or 27.5 X 106 Btu 0.68 tonnes or 4.8 barrels of crude oil 750 cubic metres or 26.5 X 103 cubic feet of natural gas 1 ò5 to 3.3 tonnes of peat or lignite (world average 2.54; Victorian brown coal 3 0) 8055 kWh (at 3.6 X 106 joules or 3412 Btu per kWh at 100% efficiency) 2660 kWh at 33% efficiency of generation 50 grams of uranium present in natural uranium reactors (see note later under nuclear energy) 0.8 grams natural uranium in breeder reactors Nuclear and hydro electricity are expressed as the coal equivalent required to produce, at 33 per cent efficiency, the same amount of electricity. In other words, electricity produced by these sources is converted to its coal equivalent at the rate of 2660 kWh = 1 tonne coal.

Jan 1, 1978

By T. Guyaguler

An analytical technique using computer-based multiple-regression methods was employed to determine the relation between the dust-producing index and inherent rock properties of typical samples from a coal-producing area, one of the aims being to provide a preliminary predictive tool for practical use. The investigation demonstrated that factors varied in their influence under different conditions, the brittleness:toughness ratio and the hardness being the most significant inherent properties with hardness showing the highest positive correlation coefficient

Jun 13, 1905

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

Many of those who attended the meeting at Chicago spent the first part of the following week in Pittsburgh, when the Experiment Station of the Bureau of Mines was dedicated and the fourth annual First Aid and Mine Rescue Contests were, held. The Bureau buildings were open for inspection during the three days, Monday, Tuesday, and Wednesday. The dedicatory ceremonies were held in the Bureau of Mines main building, Monday morning, Sept. 29, Mr. T. J. Gillespie, representing the Pittsburgh Chamber of Commerce, presiding. In his address of welcome, Hon. E. V. Babcock, Mayor of Pittsburgh, said: "The reclamation work already done stands out conspicuously beneficial to industry and populace alike all over the United States. It has demonstrated methods of preservation of life and reclaiming of injured persons which are new and greatly beneficial to modern civiliza-tion. The establishment of this institution in Pittsburgh was greatly desired, and now it is here it is greatly appreciated." The response was given by First-Assistant Secretary of the Interior Vogelsang, who represented Secretary Franklin K. Lane. He said that the Bureau of Mines did more during the war for the triumph of American arms than any other institution.

Jan 11, 1919