Search Documents

By L. I. Gyrskia, Y. V. Andreev, T. N. Greiver, G. V. Petrov

Traditionally, chromite ores are regarded exclusively as a monomineral raw material for extraction of chromium. The results of the investigations indicate a wide range of PGM in the Ray-Iz chromites, amounting to 1-3 ppm PGM. The study of products of primary gravity concentration from heavily and lightly disseminated ores (Tsentralnoe deposit, Ray-Iz block), showed that the platinum-group minerals are concentrated in the tails and slimes of the processed products, containing 10-30 ppm total PGM. Preliminary data make it possible to conclude that an in-depth study of the platinum mineralogy of the Ray-Iz block chromite ores is necessary to develop a process that will produce both chromium and the PGM.

Jan 1, 2000

By P. Barnes

It may he of interest, and perhaps of inzportance, to the members of the Institute that specific mention should be made in detail of the great value of this method of copying or photographing all kinds of tracings." Several samples are laid upon the table which may serve as illustrations of the results obtained. Some of these show slight imperfections, depending upon the character of the tracing, and upon the length of the exposure to the light, but it may be clearly seen that even a faint copy would be quite available for actual use. The process is believed to be of French origin, and has been used for many years. Special attention seems to have been directed to it recently, and its great value to engineers appears likely to be fully recognized. The manipulations required are of the simplest possible kind, and are entirely within the skill and comprehension of any office boy who can be trusted to copy a letter in an ordinary press. These particulars may be summarized somewhat thus: 1. Provide a flat board as large as the tracing which is to be copied. 2. Lay on this hoard two or three thicknesses of common blanket, or its equivalent, to give a slightly yielding backing for the paper. 3. Lay on the blanket the prepared paper with the sensitive side uppermost. 4. Lay on this paper the tracing, smoothing it out as perfectly as possible so as to insure a perfect contact with the paper. 5. Lay on the tracing a plate of clear glass, which should be heavy enough to press the tracing close down upon the paper. Ordinary plate-glass of 3/8" thickness is quite sufficient. 6. Expose the whole to a clear sunlight, by pushing it out on a shelf from an ordinary window, or in any other convenient way, for six to ten minutes. If a clear skylight only can be had, the exposure must be continued for thirty or forty-five minutes, and under a cloudy sky, sixty to ninety minutes may be needed.

Jan 1, 1879

By H. A. Steane

THIS PAPER describes the re-grind section in the 2,000-ton per day, lead-zinc flotation mill of Canadian Exploration Limited, near Salmo, B.C. There are two re-grind units in operation, one in the lead circuit, and one in the zinc circuit. In each unit, the rougher concentrate is re-ground ahead of the cleaning circuit. These re-grind units have made valuable improvements in the concentrate grade, and with no loss in recovery by over-grinding galena or sphalerite. Since the initial installation of this re-grind section, the plant throughput has been increased gradually from 1,600 tons to 2,000 tons per twenty-four hours, and, as shown by the screen analysis of mill tailing, a coarser overall grind has been accepted, from 55 per cent to 45 per ?cent minus 200 mesh. There has been no increase in grinding capacity, but two mills have been taken from the main grinding circuit and used for the re-grind circuit.

Jan 1, 1958

By L. L. Tavlarides, N. V. Deorkar

"Recovery/Recycling of metal ions from industrial process waste streams is a preferred alternative to disposal by conventional techniques. This paper presents methods for preparation of inorganic chemically active adsorbents to be used in fixed bed adsorbers. Methods for immobilization of chelating agents on the inorganic supports are discussed. The prepared adsorbents are characterized to determine coverage density of functional groups, effect of pH on metal ion removal efficiency, regeneration efficiency and uptake capacity. Results from the laboratory scale and bench scale experiments are presented here.IntroductionRemoval of heavy metal ions from processing wastes in various industries is an important problem. Waste streams in electroplating, electronic, catalyst preparation and hydrometallurgical industries contain metal ions such as copper, nickel, chromium, lead, tin, cadmium, silver, gold and platinum. One major concern for the non-ferrous metal industry is secondary recovery of precious metals and cyanide from cyanide leachate from smelter residue and hydrometallurgical waste streams.Recovery methods recently considered include evaporation, electrolyte metal recovery, reverse osmosis (1), adsorption, ion exchange (2,3), membrane separation (4,5) and Solvent extraction. These processes have met with various levels of limited success. The use of liquid ion exchange molecules to selectively extract metal ions for on-site treatment of these waste streams is currently receiving substantial interest (6,7). This interest seems from an awareness of the advances made in the development of commercial extractants for metal ion separation in hydrometallurgical industries (8). However, separation by solvent extraction processes is generally considered to be economical in the range of aqueous metal ion concentrations from 0.01 to 1.0 mol/lit (9). In order to exploit the selectivity of chelating agents, the idea of immobilizing chelating agent into a solid matrix has attracted growing attention in recent years. Many supports such as inorganic oxides, organic polymers, cellulose powder and polyurethane foam can be used for immobilization of chelating agents. Over the last decade, considerable efforts have been directed toward attachment/introduction of chelating agents into a polymer matrix (10,11). Inorganic supports as compared to polymer supports provide high mechanical strength, chemical and thermal stability, and high reaction rates due to open pore structure. On the contrary, organic resins shrink and swell, thus affecting mass transfer (12). Many of the disadvantages of polymer supports can be excluded by the use of inorganic supports. Innovative use of immobilization techniques can produce inorganic chemically active adsorbents with comparable capacity, stability and reaction rates. Consequently, the objective of our program is the development of inorganic chemically active adsorbents to be used in a fixed-bed unit operation as an alternative heavy metal ion recovery process. Methods of preparation of inorganic chemically active adsorbents, (ICAAs) characterization and applications are discussed in this paper. A brief summary of the results from laboratory scale studies and bench scale studies is presented."

Jan 1, 1996

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By A. W. Davis

Sapping and mining have constituted an important part of siege operations ever since powder came into general use in Europe. Before this period, famine was the main weapon in the hands of the besiegers, and the history of the middle ages is replete with accounts of sieges lasting two and three years. With the advent of explosives, a position impregnable to assault might be readily won by mining under, and blowing up, its defences. The natural offensive against this method of attack is to countermine and stop the attackers underground before their objective is reached. Thus developed the art of military mining. The French and British, in the Peninsular war, were adepts at this method of warfare, and the explosion of a mine and the formation of a breach were the usual preludes to the general assault of a position. In the Crimea, at Sebastopol, the British and Russians did a lot of underground fighting, as the old maps of their galleries, now in the museum at Chatham, will testify. In the siege of Port Arthur, in still later times, the Japanese and Russians were hard at it as well.

Jan 1, 1926

By B. M. P. Pingua & Md. Nabiullah

About 60 to 70 percent of bulk explosives are used in Indian coalmines to achieve coal production for power generation. Coal India Limited (CIL) is the major coal producing company in India. The average production of CIL is 400 to 450 million tonne coal per annum. The major subsidiaries of CIL are Northern Coalfields Ltd., Mahanadi Coalfields Ltd., Bharat Coking Coal Ltd., Eastern Coalfields Ltd, South Eastern Coalfields Ltd. and Western Coalfields Ltd. Most of the mines of CIL have watery holes. Therefore, high water resistance bulk explosives are preferred for better out puts.

Jan 1, 2008

COAL is perennially -a subject of major interest at. Pittsburgh, but during the week of Nov. 19 to 24 it was especially to the fore because nearly two thousand persons gathered to take part in the second of the international conferences organized by President Baker of the Carnegie Institute. From the opening session on Monday morning when those attending were welcomed by President Baker and T. P. Gaylord, president of the Chamber of Commerce of Pittsburgh, until the party returned from the Clairton coke ovens on Saturday. afternoon, there was something going on all the time, and usually three sessions were in progress at once.

Jan 1, 1928

By H. F. Smiley, Fred Sehmann

The production of the North Central Texas area comes entirely from the Pennsylvanian section with the exception of one pool in Cooke County and one in Young County where oil has been, produced from the weathered surfaces of Pre-Pennsylvanian peaks overlapped by oil-bearing strata of Pennsylvanian age. In the southern part of the area the Strawn and Bend groups furnish the production, the Strawn sands being the predominating horizons at depths from 1500 to 3000 feet. In the northern part of the area including North Young, Archer, Wichita, Wilbarger, and Clay counties, the Cisco group has produced consistently for nearly 30 years from sands ranging in depth from 700 to 2500 ft. To our knowledge there are 13 separate producing sands in t,he Cisco group ranging from 200 to 1800 ft. in Wichita County. During the past three years, deeper drilling has opened three new producing horizons. A Canyon sand in Central Archer County has produced from 400 to 800 bbl. per well at a depth of 2200 ft.; and in the same pool, owned jointly by the Deep Oil Development Co. and Lindsay Drilling Co., a Strawn sand was found at 3600 ft. which produced 75 bbl. per day. In Southern Wichita County the Bend group has been found productive. A very oolitic sandy lime series from 3675 to 3942 ft. has produced in three wells drilled to date. During the past year the district has been producing under an extreme proration which accounts for the small production figures for 1932, as well as the few drilling activities at the end of the year. Table 1 presents the available drilling and production data compiled by the North Texas Oil and Gas Association.

Jan 1, 1933

By R. Havens

During the course of the investigation of possible domestic sources of manganese, engineers of the Bureau of Mines examined and sampled two manganese mineral deposits in northeastern Utah. The Daggett Chief claims are situated in the northern part of Daggett County,5 miles southwest of Manila, Utah, and approximately 57 miles from Green-River, Wyo. Owners of the property are J.E. Harris Of Salt Lake City, Utah, Nels Palleson of Manila, Utah, and J. P. Larson. The manganese occurs in a vein 6 to 8 feet wide in a shale and sandstone formation. Two distinct occurrences Of manganese are present Within the vein, and samples of each were subjected to testing. Lot A, representing .probably the major portion of the Manganese; was composed of nodules and veinlets of manganese oxides in a semicompact; gray, shaly formation. Lot B represented a 15-inch vein of dense iron-manganese ore. .Most of the laboratory work at Salt Lake City, Utah, was done on these two samples; but preliminary testing also was carried out on a small sample, physically similar to lot A, submitted by the owners.

Jan 1, 1949

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By Mary E. Learmont

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression.. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1984

By A G. Greenwood

Research into cemented rock fill at Mount Isa Mines Limited since 1992 is described. The key mechanisms controlling segregation during stope filling with cemented rock fill are described and include the gravity flow mechanism which is described in detail. Examples are provided to demonstrate these mechanisms. Comparisons are made between Mount Isa MinesÆ cemented rock fill and slurry-based cemented rock fills. Recent backfill stability modelling using a three-dimensional finite element program is described.

Jan 1, 1998

Jan 1, 1963

By Cyril Smith

A STUDY of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published1 giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. PREPARATION OF ALLOYS The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 percent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2-in. dia. casting, the turnings being separated into three parts according to the position

Jan 1, 1931

Objective: To devise a passive means to detect overheating insulators on mine trolley/track haulageways.

Aug 1, 1998

By Gilbert DJ, Lemon NM

A case history of a two year study of low grade ores in the Middleback Range area with the objective of defining possible areas of interest from a combination of geological- petrological-metallurgical criteria. Covering the general geology of the area and ore types; the results of metallurgical testwork and the pattern of evolution of these tests; the petrological explanation of the results of the testwork; the culmination of the work in the selection of areas of best potential for more intensive work. Jaspilites consisting of magnetite, hematite and limonite with quartz and silicate-carbonate-sulphide minerals are hosts to high grade iron mineralisation but also constitute a large low grade iron Reserve.

Jan 1, 1975

By H. S. Rathor

In a major hydropower project in the Himalayas, during excavation of tunnel, hydrothermal gradient line appeared and caused extremely unfavorable conditions with rock and water temperature varying between 55°–66°C and nearly 100% humidity. Major changes in method of excavation, schedule of works, deployment of additional equipments and acclimatization of personnel were made to complete this unfavorable stretch of world’s longest Head Race Tunnel. The case study covers the various aspects of tunneling in geothermal rocks, inhuman working conditions, loss of production, cost overrun, contractual claims and strategy to manage such unfavorable working conditions.

Jan 1, 2003

With the inauguration of Petroleum Technology this year, and approval by the Board to add an Assistant Secretary to the New York staff to serve the Petroleum and Coal Divisions, the Petroleum Division looks forward to greater opportunities and responsibilities. An improved medium of publication offers further incentive to engineers and investigators in the oil industry to make contributions. The authorization by the Board of Directors of a new Assistant Secretary is an appreciation of the splendid contributions made to the industry by the open forum of the Petroleum Division. It is also a recognition of the possibilities of greater service to the membership along the lines established ten to fifteen years ago by DeGolyer, Fohs, Ambrose and Lovejoy, to mention a few leaders. It isexpected that the new officer will spend a substantial part of his time in the field, visiting the student sections, the respective Divisions, helping in the arrangement of papers and Section meetings and intensifying interest in the Institute. The Petroleum Division will hold three meetings this year. The Fall Meetings will be held on Oct. 6 and 7 in San Antonio and on Oct. 20 and 21 in Los Angeles. The programs for these meetings will deal chiefly with engineering research and production engineering problems. Papers on production statistics and general economics of the industry are reserved for the Annual Meeting in New York. The annual production symposium and statistics are accepted as standard for the industry. With continuously deeper penetration into the earth in search for and exploitation of petroleum, it is necessary to have a better understanding of reservoir conditions and to place more phases of the operation under engineering control. Among the subjects relating to reservoir conditions tha thave been proposed for the fall meeting programs are phase equilibria at high pressures, interfacial tension between oil and water, the flow of oil and water through sands, the chemistry of films and underground temperatures. Investigations relating to control of operations include methods of continuously logging while drilling both visually and electrically, methods of studying drilling samples, properties of drilling fluids, improved cementing practices for isolating thin sands under high-temperature conditions and gas conservation, particularly production from high-pressure reservoirs. Additional suggestions of general themes or individual subjects will be welcomed, since it is desirable to build a backlog of material for Petroleum Technology. 9

Jan 1, 1938