Search Documents

By S. F. Shaw

The principles involved in lifting oil in wells flowing naturally are identical with those underlying the flowing of wells by means of the air-gas lift, and information of a dependable nature obtained in the study of the air-lift can be applied to wells with natural flow. A well flowing naturally is one in which the lifting is done by means of the gas-lift, for which the gas is supplied entirely by the formation from which the oil is derived. In air-gas lift operations, there is insufficient gas supplied by the formation to lift the oil to the surface in an efficient manner, therefore additional gas for this purpose must be furnished from an outside source. There may, at times, be conditions obtaining in natural flowing wells different from those in wells flowed by gas-lift, but these differences do not at all conflict with the main principles of gas-lift work. One such condition is met with in wells in which the gas supplied by the formation is in considerable excess of that required to lift the oil to surface; this excess may be so great as to reduce the quantity of oil that can be lifted through the particular diameter of casing or tubing that has been lowered into the well. This same condition can be brought about, however, by supplying a large excess of gas from an outside source to an artificial gas-lift well, and a study of the effects obtained from injecting a large excess into the well can be applied directly to handling wells flowing naturally which have a large excess of gas supplied by the underground reservoir. Conditions for Lifting Oil The main factors to be considered in flowing wells are as follows: 1. Submergence, or pressure at the bottom of the tubing or casing. 2. Lift; the height to which the liquid must be raised. 3. Diameter of the flow tubing or casing. 4. Quantity of liquid to be lifted. 5. Pressure at the discharge end of the flow tubing, or back-pressure, as it is sometimes called.

Jan 1, 1930

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By F. E. Wood

This paper is written primarily as a discussion of Dr. W. P. Hase-man's paper on "A Theory of Well Spacing"' and presents briefly the production records, and intensity and rate of development in a large portion of the two principal producing sands in the Salt Creek field, Wyoming. The study includes 1350 wells, 160,000,000 bbl. production, well spacings varying from two to seven wells per 40 acres and early and late development. The general conclusions to be derived from this study are: 1. It is impossible to formulate a mathematical rule to apply to well spacing in the Salt Creek field. 2. Each tract is a separate problem. 3. Tracts first drilled produce the most oil, with many exceptions. 4. Initial production is not a reliable index to the relationship between past, current, or future production. 5. Wells which have produced the most oil in the past are not necessarily yielding the greatest current production nor will they yield the greatest future production. In fact, wells which have yielded the greatest past production will, in at least one-half the cases, make less oil currently or in the future than wells which have produced a smaller quantity of oil in the past. 6. The following is a safe rule to apply in well spacing in the Salt Creek field: (a) If the drilling of an additional well on a tract results in a sustained increased production, with prospects of making a profit, the tract is not overdeveloped and additional wells might be drilled. (b) If the drilling of an additional well does not effect a sustained increase in the production of a tract, the tract is fully developed. Second Wall Creek Sand The Second Wall Creek sand, covering 20,000 producing acres, is the principal producing horizon in the Salt Creek field; 1610 wells are producing at this time from this sand. This paper deals with hut a portion of the entire field including 10,680 of the more productive acres,

Jan 1, 1930

By Bernard Moore

AT present the demands of the United States for strontium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits are TABLE 1.-Strontium Imported into the United States, 1926-1932a Ore Chemicals Year Short Tons Value Pounds Value 1926 2,200 $58,159 5,433,044 $115,436 1927 1,356 58,711 4,233,816 149,383 1928 759 31,157 3,380,464 136,561 1929 973 45,505 4,578,327 196,233 1930 220 10,459 2,153,788 104.807 1931 (260 lbs.) 123 1,742,714 83,564 1932 5 276 469,481 20,910 a Mineral Industry (1934) 42, 61. known in many states, but the, larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, par-ticularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investi-gation of the mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work.

Jan 1, 1935

By Samuel Sigman, Martin M. Cooper

A basic ingredient for rapid tunnel excavation is material handling. In construction of tunnel projects in urban areas material handling requires additional input to maximize performance. Urban projects share the same problems experienced in all tunnel construction and they must be dealt with. Howeve.., Urban constraints add a larger dimension. APPLICATION ENGINEERING A MUST A word of caution. To achieve increasing speed of excavation in tunnels whether in Urban areas or elsewhere will require much creative thought and energy. It would be a false premise to assume that major breakthroughs will result from this conference, or shortly thereafter, or to hope that a success here or there can translate into a universal solution. The reality, as we see it is that rapid progress and great economies will accrue on any given project only if effective application engineering is carried through. By all means take advantage of past experiences but, do not at the peril of costly undertaking, blindly accept the program of a successful job elsewhere as automatically suited to your project. Tunnel construction in urban areas is at best a difficult undertaking made more difficult in this period of greater awareness of environment, of conservation and of the quality of living by sophisticated urban communities,. A construction job represents a necessary nuisance to urban communities. To minimize this nuisance many regulatory laws are adopted. These regulations can and do slow down tunnel jobs and pyramid costs.

Jan 1, 1974

By Belmira Benedita de Lima

Estudos no sistema Nb-B mostram a fase Nb5B6 com formação peritética a partir do líquido, porém sua estabilidade abaixo de 2.000°C não é comprovada experimentalmente. Há também dúvidas sobre a ocorrência da fase Nb2B3 neste binário. Este trabalho tem como objetivo o estudo da estabilidade das fases Nb5B6 e Nb2B3 nas temperaturas de 1.400°C e 1.800°C. Amostras com composições nas estequiometrias Nb5B6 e Nb2B3 foram produzidas através de fusão a arco assim como confeccionadas a partir de misturas de pós de B e NbB. Pastilhas com composição Nb5B6 foram produzidas com e sem adição de semente da fase Nb5B6. Os tratamentos térmicos em 1.400°C foram realizados por até 10h enquanto aqueles em 1800°C por até 1h, todos em atmosfera estática de argônio. As microestruturas das amostras, tanto no estado bruto de fusão como após tratamento térmico, foram caracterizadas por difração de raios X (XRD). Os resultados confirmam a formação fase Nb5B6 a partir do líquido e nas amostras produzidas via metalurgia do pó. A fase Nb2B3 não é observada nas amostras no estado bruto de fusão e nas amostras produzidas via metalurgia do pó tratadas termicamente a 1.800°C, porém, esta fase se estabiliza nas amostras produzidas via metalurgia do pó tratadas a 1.400°C, indicando sua estabilidade com formação peritetóide a partir das fases Nb3B4 e NbB2, abaixo de 1.800°C.

Aug 8, 2018

By L. G. Austin

The use of crushed power station slags, both natural and coated, as granules for roof shingles shows some promise. Test shingles weathered for some years showed rust spotting and granule deterioration as serious problems. Chemical analysis on a particle-by-particle basis using a scanning electron microscope-energy dispersive spectroscopy system showed the wide variability of chemical composition of the granules within a given sample. Analysis of particles acting as sources of spotting within the weathered samples showed high iron contents but no rules could he developed for predicting the long-term stability of different compositions.

Jan 1, 1990

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219 3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button o your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gov Internet/Gopher Server Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gov Internet System Administrator: webmaster@usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By Ruth F. Brinkley

This circular describes the activities and publications of the Bureau of Mines, Explosives Research Laboratory4 for the fiscal year 1960 (July 1, 1959 -June 30, 1960). Part 1 describes briefly the principal projects that were active during the report period, and presents some data not scheduled for publication elsewhere in the near future. Certain of the results are only preliminary and should be regarded as tentative, pending the findings of the completed investigation. Publications that appeared during the report period are listed and described briefly in part 2. In general, the research activities reported in these publications antedate fiscal year 1960. The published material relating to activities that are still current is indicated by references in part 1.

Jan 1, 1962

By Enrique Mansilla Navarrete

El presente texto describe las investigaciones recientes sobre el uso del caolín como "rellenador" en las diferentes industrias y artes. Los "rellenadores" o "fillers" son materiales qúimicamente inertes, cuya acción es básicamente física. Entre las características de los "fillers" tenemos la densidad aparente, tamaño de partículas, capacidad de absorción, abrasividad, porosidad, comportamiento térmico y una velocidad de sedimentación adecuada. De acuerdo a estos parámetros señalados, se desarrolla un programa exploratorio, los métodos empleados y la descripción de su uso en algunos depósitos encontrados en Cajamarca.

Nov 8, 1982

By T. M. Chance

THE term "low-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as 1 ½ per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low sulfur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, With few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 ½ per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous dis-tricts, it has been necessary to turn to the areas of higher-sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.-Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout

Jan 8, 1919

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By William R. Hardwick

Present information indicates that a copper deposit can be safely fractured with a nuclear explosive and the copper successfully recovered by the in-situ leaching method. The process is not yet at the stage where it can be presented t ) the mining industry as a technique proven in all its aspects, but it is a method with high success potential. Unknown factors must be evaluated by a full-scale test before the economics or the extent of the use of the method by the mining industry can be predicted. Preliminary calculations indicate that the cost of fracturing a copper deposit nuclear explosives may range from l.8 to 55.2 cents per ton or in some case: less than a cent per pound of recoverable copper. Copper may be recovered at less cost than by conventional methods. Deposits with 4 pounds of recoverable copper may be economic and production from a deposit may begin in less than half the time required for conventional methods.

Jan 1, 1967

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

Mine Taxation On Monday morning, Sept. 22, a session on- Mine Taxation was held in cooperation with the Internal Revenue Dept., U. S. Treasury, Mr. R. C. Allen presiding. This was followed by two adjourned sessions, at which Mr. R. C. Allen and Mr. A.D. Brokaw presided. The following paper was presented: Federal Taxation of Mines. By L. C. Graton. (Presented by the author; dis¬cussed by R. V. Norris, W. O. Hotchkiss, W. P. Beldon, Paul Armitage, R. C. Allen, E. F. Brown, William Belly, A. D. Brokaw, F. W. Sperr, C. H. Benedict, E. P. Griffitts, W. E. Forsythe, and the author). Coal and Gas The first session on Coal and Gas was held on Monday morning, Sept. 22; the second, on the afternoon of the same day. Mr. Curl Scholz presided at both sessions. The following papers were presented: Research on the Coal-mining Industry. By E. A. Holbrook. (Presented by the author.) Some Factors that Affect the Washability of a Coal. By Thomas Fraser and H. F. Yancey. (Presented by the author.) A Use Classification of Coal. By George H. Ashley. (Presented by title.) Distribution of Anthracite. By A; S. Learoyd. (Presented by title.) Height of the Gas Cap in the Safety Lamp. By C. M. Young. (Presented by the author.) Engineering Features of Modern Large Coal Mines in Illinois and Indiana. By C. A. Herbert and C. M. Young. (Presented by the authors.) Gas-producer Practice. By G. S. Brooks and C. C. Nitchie. (Presented by the authors.) Testing of Coals for Byproduct Coking and Gas Manufacture. By Horace C. Porter. (Presented by the author.) Coals of Ohio and their Limitations for Byproduct Coke. By Wilber. Stout. (Presented by the author.) Outdoor Substations in Connection with Coal-mining Installations. By H. W. Young. (Presented by the author.)

Jan 11, 1919

By Hugo Barrientos

"The growing need to optimize the mining processes produces a need for users to have a simple, reliable, secure and cost-effective method to monitor the values of the variables measured in field. The solutions described in this paper, we will demonstrate how the implementation of Emerson Smart Wireless technology helps to optimize the leaching and electro winning processes. An effective monitoring of the variables involved in the operation of a heap leach, such as pressure, flow rate, pH, water level control and regulator valves can improve production and optimize the use of sulfuric acid, which results in a more effective management of resources and helps reducing input costs. Moreover, the constant monitoring of variables prevents the risk of landslides, reducing maintenance costs. In electro winning cells, the wireless solution measures variables such as pressure, flow rate, temperature and voltage provides a performance indicator for the entire operation, capable of detecting and predicting shorts, and monitoring the overall functioning of a cell or group of cells. As a result of the applications studied, users can monitor variables in real time, optimizing the use of resources, quickly detecting possible flaws in the process and reducing the risks in the operation. All these factors have a direct impact on company results."

Jan 1, 2014

By A. Noble

"A supply of sustainably sourced rare earth elements (REEs) is critical for several high-tech industries, renewable energy technologies, and defense applications. Recent studies have shown that REEs exist in coal and coal combustion byproducts at elevated concentrations and in quantities that could meet domestic demand. Despite these promising findings, declines in rare earth prices, volatile commodity markets, and challenging geo-metallurgical conditions have jeopardized this potentially valuable REE resource. While the dilute REE concentrations inherently necessitate low-cost separation technologies, the ultimately operating cost threshold for economic extraction must be based on commodity price projections and market demand. In this paper, the micro-pricing principle is used to develop a rigorous economic model assessing the inherent value of REEs in coal materials. This model is based upon basket pricing of individual elemental oxides, and elemental distributions of coal samples from various basins. These results may be used to assess the economic viability of potential REE concentration and refining technologies INTRODUCTION Recent efforts by US Department of Energy (DOE) and the National Energy Technology Laboratory (NETL) have suggested that rare earth elements (REEs) may exist in coal and coal byproducts at concentrations suitable for economic extraction and processing. While the knowledge of REE occurrence in coal material dates back over 50 years, recent supply restrictions and material criticality considerations have prompted a national interest to establish a sustainable domestic supply of REEs. REEs are not “rare” in the sense of crustal abundance; however, few natural processes lead to concentrated ore deposits. As a result, the elevated concentrations found in coal material may provide a potentially promising resource for these materials. While the term “rare earths” is often used to describe a singular concept, the 15 rare earth elements actually have varying and sometimes contrasting scarcity and cost profiles. Various authors have proposed classification systems to provide information on REE criticality (e.g. Seredin and Dai, 2012, Zhang et al., 2015). The most straightforward classification is provided on the basis of geochemistry with designations for “light”, “medium” and “heavy” rare earths. Light rare earths (those to the left of the periodic table: Ce, Pr, Nd, and Sm) tend to be more common and less valuable when compared to their medium (Eu, Gd, Tb, Dy, and Y) and heavy (Ho, Er, Tm, Yb, and Lu) counterparts. While light rare earths are often found in traditional ore deposits at economic concentrations, the heavier rare earths are almost exclusively found as ion-absorbed clays (Seredin and Dai, 2012)."

Jan 1, 2016

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943