Search Documents

By E. M. Wise

THE practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired- to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgren1 and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward,2 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents,5 and are becoming of commercial importance in the production of high-strength castings.

Jan 1, 1934

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,' transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By A. C. Fraker, H. H. Stadelmaier

WIENER and Bergerl reported the existence of the nitrides Fe3NiN and Fe3PtNwith a cubic L1'2 structure. The present note shows that a similar nitride Fe3PdN can be observed and that the composition range between the iron nitride Fe4N and the nitrides Fe3NiN, Fe3PdN, and Fe3PtN is occupied by single-phase cubic nitrides with structures intermediate between L1' and L1'2. The materials used in this investigation were electrolytic iron of 99.9 pct purity, carbonyl nickel of 99.7 pct purity, sponge platinum of 99.95 pct purity, and palladium sheet of 99.8 pct. purity. Binary alloys of the transition metals were induction-melted in a crucible of fused alumina, powdered, and screened to a particle size of - 200 mesh. The powders were nitrided at 600°C in a gas mixture of ammonia and hydrogen, and the crystal structure was determined with the aid of a Wilson powder camera. The results are compiled in Table I together with information from the paper of Wiener and Berger.1 The compound at the nominal composition Fe3PdN has a diffraction pattern with prominent reflections of a face-centered cubic lattice (h2 + k2+l2 = 3, 4, 8, 11, 12, 16) and weaker superstructure lines (h2 + k2 + 12 = 1, 2, 5, 6, 9, 10, 13, 14). With decreasing palladium content the superstructure lines become weaker and approach the intensity of those of Fe4N. No analysis was made of the intensities, but it can be assumed that the structure is that found by Wiener and Bergerl in Fe3NiN and Fe3PtN, namely L1'2 (perovskite structure) with both palladium and the interstitial nitrogen fully ordered. The dependence of the lattice constant upon the solute atom (Ni, Pd, Pt) content can be explained tolerably well by simple lattice expansion due to subsequent work confirms this suggestion, it will be of significance to order-disorder theory. The author is grateful to Lester Guttman for discussions on this topic.

Jan 1, 1961

By P. E. Cavanagh

SINCE the 1930's' the production of iron ore in Canada has increased from zero to about 15 million tons per year. In the same short period of about 25 years, the steel industry has doubled in output, while the consumption of steel has also doubled. In the 1930's all Canadian steel was made from imported iron ore, whereas today, Canada is exporting considerably more iron ore than she imports. It appears certain that the production of iron ore in Canada will at least double in the near future, and should be over 45 million tons per year at the end of the next 25 years, in 1980. It also appears certain that most of this iron ore will be exported to the United States, with some proportion going to Europe. In this situation, it is logical and proper at the present time for Canadians to consider means of converting some of all of this Canadian iron ore into semi-finished or finished products in Canada.

Jan 6, 1958

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

By J. S. Blakemore, E. O. Hall

SERRATED yielding, commonly called the Portevin-Le Chatelier effect, is known to occur in a wide range of alloys where the moving dislocations are considered to be locked by the diffusion of solute atoms to them. From the work of Cottrell,1 an approximate relationship between strain rate, E, dislocation density, p , and solute diffusion coefficient, D, giving rise to serrated yielding is: e =Dp

Jan 1, 1969

By Alexander Sutulov

Si bien América Latina posee una riqueza mineral extraordinaria y es un importante proveedor de materias primas en el mercado internacional, no hizo un buen uso de sus recursos minerales. En ese sentido, el presente texto señala el análisis económico y tecnógico de Latinoamérica frente a la demandas de tres potencias industriales (EE.UU., Europa Occidental y Japón) que, al mismo tiempo son los principales clientes. Para mantener su ritmo de desarrollo industrial, Latinoamérica necesita divisas provenientes de la exportación de materias primas, donde la conservación de los mercados y el aprovechamiento de los mismos. Asimismo, es necesario un mayor grado de elaboración y purificación de materias primas y que la producción de productos minerales sea de alta calidad a precios competitivos.

Sep 1, 1969

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By M. Clotilde Apua, A. F. Mulaba-Bafubiandi

"The efficiency of hydrochloric acid (HCl) leaching of gold from low grade gold-bearing material has been investigated in the presence of sodium hypochlorite (NaOCl) to produce in situ chlorine gas which is an oxidizing agent able to oxidize gold metal to its soluble forms. The effect of concentrations of HCl, NaOCl, and mixtures of HCl + NaOCl was sought. Iron and potassium present in the feed were leached and consumed all the HCl. Gold found as inclusion in pyrite was not exposed to the lixiviant. Therefore, leaching of gold from low grade gold-bearing material in aqueous chlorine solution is not an effective process for now.INTRODUCTIONHydrometallurgy of gold is commonly based on cyanide leaching solution. Due to the environmental concerns related to cyanidation and mercury processes, and inefficiency of cyanide gold leaching to dissolve refractory ores, sustainable alternative lixiviant systems, capable of generating gold (I) and gold (III) complexes must be studied. Amongst non-cyanide gold lixiviants there is the chloride/chlorine system (Hilson and Monhemius, 2006; Senanayake, 2004; Pilsniak and Trochimczuck, 2007; Wang et al., 2007; Reeves et al., 1999; Khodadad et al., 2008).In practice, the most oxidizing agents utilized for the leaching of gold as chloride, are chlorine (Cl2) or hypochlorite (HOCl) which are either generated in situ by suitable reaction or added in solution (Adamson, 1972). The dissolution of gold concentrate using hydrochloric acid, sodium chloride and sodium hypochlorite (Cl-/HOCl system) were studied (Puvada and Murthy, 2006). The effect of NaOCl and NaCl concentrations were also investigated. The leaching was performed under the following conditions; time: 4h, solid–liquid ratio = 1:4, at room temperature. It was found that the increase of the NaOCl concentration from 25 to 75 g/L did not have any meaningful effect on the recovery of gold which was about 30% (experimental conditions; S/L ratio = 1:4, NaCl concentration: 25 g/L, HCl concentration: 0.35 M). It was also found that from 25 g/L to 200 g/L NaCl, the recovery of gold rose from 30% to 40% (experimental conditions; S/L ratio: 1:4, NaOCl concentration: 25 g/L, HCl concentration: 0.35 M)."

Jan 1, 2012

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By W. C. Lilliendahl, G. Meister

Uranium metal with a purity of about 99.9 pct was produced on a large scale by fused salt electrolysis with a material efficiency of about 90 pct. The material efficiency depends mainly on bath composition, electrolysis temperature, electrode smothering, and elutriation during washing of the powder. RESEARCH and development work on fused salt electrolysis carried on by the Westinghouse Lamp Div. Bloomfield, N. J., was done under the Manhattan District Corps of Engineers and later under the Atomic Energy Commission for the commercialization of uranium production for the first atomic pile at the University of Chicago in 1942. From the conception of the atomic bomb project it was recognized that metals with impurity levels having little metallurgical significance would be required. Permissible impurity levels were based on neutron absorption. Of particular significance was boron, which could not be present in amounts exceeding 1 ppm. The electrolytic method as developed in 1930 by Driggs and Lilliendahl,1,2 and later improved, yielded uranium of very low boron and other deleterious impurity content. No other method was capable at that time of producing uranium metal of the required purity.' The low boron content of uranium produced by the electrolytic process resulted from the availability of the reactants which were low in boron content, and from the inherent elimination of boron in the fused salt bath. Since the heart of any electrolytic process is the electrolysis cell, this paper will deal with the development of the original bath composition for the efficient production of uranium from a batch process to one of continuous operation. Emphasis also will be placed on other factors which will affect the material efficiency of the process. With the laboratory cell the material efficiency of uranium powder recovery in the early electrolysis was relatively low, about 35 pct based on the ratio of uranium recovered to uranium added. This early process also had other defects. The electro- lytic bath could not be used continuously. After three runs from a freshly charged crucible, the deposit showed a tendency to slip off the electrode as it was raised from the bath. This condition necessitated pouring the charge every fourth run and preparing a new bath. It was assumed at that time that this condition was caused by the increasing fluoride concentration with each addition of uranium salt, which adected the mobility of the uranium ions. Experimental The electrolysis cells differed in size only. They were of the floating cathode type. The laboratory cells were 21/2 in. ID and 6 in. deep and operated at 30 amp and 5 volts. Production was about 150 g metal powder per 8 hr. The plant cells (5 units) were 9 in. ID x 21 in. deep and operated at 1800 amp at 12 volts. The total production unit was designed to produce 250 lb of uranium powder per 8 hr day. Because of the tendency of uranium fines toward spontaneous combustion, material efficiencies were based only on the recovery of useful coarser metal which could be safely handled. The reported efficiencies are of particular significance only as related to the same group of experimental procedures. At the start of the project no changes were contemplated until previous data could be definitely confirmed. Therefore, the first experiments were with the 50 pct CaCl2-50 pct NaCl mixture. The material efficiency of uranium deposition as a function of the number of electrolyses is shown in Table I. In Table I, the decrease in efficiency at 800°C with number of runs is apparent and confirmed the earlier data. Operating at 900°C enabled the number of runs to be doubled, but before pouring the charge the efficiency of recovery became poor. This test indicated that the improved efficiency might have been caused by an increase in the fluidity of the bath.

Jan 1, 1958

By James A. Roberson

THE mechanical behavior of molybdenum has become a matter of considerable interest in recent years because it has a reasonably high strength at high temperatures. Various aspects of its fatigue behavior have been investigated previously,1-3 and the results can be summarized as follows. Recrys-tallized molybdenum exhibits a fatigue limit which decreases continuously with increasing temperature. The ratio of fatigue-limit stress to ultimate tensile stress is high (0.6 to 0.8) and reasonably constant. The present work was undertaken to determine the effect of variations in environment on the fatigue of molybdenum stressed in fully reversed axial tension compression. In order to provide a basis to which these data could be compared, a complementary series of fatigue tests were made in vacuum. All of the specimens used were made from one mill lot of unalloyed molybdenum which had been vacuum-arc melted, worked down to 1-in.-diam bar, re-crystallized, then warm-worked to 5/8 in. diam. The interstitial content by weight was as follows: C—0.022 pet, 02-0.0026 pet, Hz-0.0001 pet, and N20.0002 pct. The average grain diameter in the transverse direction was about 0.035 mm, and the average grain length was about 0.15 mm. Typical tensile-test data are shown in Table I. None of the specimens tested exhibited an upper yield point.

Jan 1, 1965

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects, derive p-y curves for reinforced concrete fixed head piles and to validate currently available p-multiplier models. The piles are identical in diameter of d=2 ft and were tested in similar soil conditions. The single pile as well as in three piles within the pile group were instrumented with internal sensor instrumentation to record pile curvatures. External instrumentation was used to control and measure the lateral displacement of the specimens. Experimental studies were supported with analytical models to enable comparisons and offer design recommendations. All test specimens were tested to structural failure and group interaction factors ranged between 0.8 at small displacement levels and increased towards unit near structural failure. A set of p-multipliers was found to reproduce an accurate fit to the available test data.

Jan 1, 2010

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By R. W. Armstrong, P. C. Jindal

TABOR1 has indicated for a number of polycrystal-line materials that their hardness should be directly related to their yield strength. For a material showing zero work-hardening, the Meyer hardness, MH, may be calculated in terms of the yield stress, sy, by utilizing slip line theory and the result is: The Meyer hardness corresponds to indenting the surface with a spherical indenter and specifying the ratio of load and projected area of the indentation. The correlation indicated by Eq. [I] is not well-established. It has been verified to some degree by performing hardness tests on materials strained to the maximum nominal stress and taking this stress as the (new) yield stress of a nonwork-hardening material. The dependence of hardness on yield strength for an annealed material capable of showing work-hardening has not been theoretically evaluated but, presumably, the hardness should be greater than that specified above. Marcinkowski, Fisher, and szirmae2 measured the dependence of the Vickers Diamond Pyramid hardness, H,, on yield strength for an annealed Fe-Cr alloy which shows work-hardening and found:

Jan 1, 1968

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By Herbert Kilburn Scott

The information in this paper was collected by the author during a five years' residence in the State of Minas Geraes. Outside the State itself, very little is known of the gold-field. Such accounts as have been published are antiquated and contained in publications mostly out of print. The increased attention now attracted to the natural resources of Brazil, and the probability that American capital will be, in the near future, largely invested there, will make an up-to-date account specially useful at this time. I. Historical and General. Soon after the Jesuits founded what is to-day the city of S?o Paulo, gold was discovered in the streams of the neighborhood; and this incited the natives, known as paulistas, to look for it farther afield. After many expeditions into the interior, gold was found in quantity in placer-deposits in the vicinity of Ouro Preto, in 1699, by a prospecting party headed by Antonio Dias. The name of Ouro Preto (black gold) was given because of the superficial dark coating of the gold, and the inhabitants of the district were known as mineiros (miners). Later on, the placers of Cuiaba, in the State of Matto Grosso, were discovered in 1718, and those of the State of Goyaz in 1724. All this territory was at the time a private colony, but on account of its increasing importance it was taken over by the Crown, and in 1739 a royal governor was appointed, with his nominal capital in S?o Paulo, though for a number of years the real capital was Ouro Preto. In 1711 Ouro Preto was raised to the rank of a city, with the name of Villa Rica de Ouro Preto (" rich city of black gold"); and in 1720, by reason of administrative difficulties, Minas Geraes was constituted a separate colony from S?o Paulo, with Villa Rica as its capital. The site of this city

Jan 1, 1903

By F. Samimi Namin

One of the main tasks in exploitation of mines is to select a method suitable for the deposits, specific features including geometric, geo-mechanical and geological features. The purpose of selecting a mining method at this stage is to choose one or more method(s) having the most coordination with the deposit?s conditions and external factors, including the allocated budget and local technology for detailed feasibility studies. Several methods have been developed in the past to evaluate suitable mining methods for an ore deposit, based on its physical characteristics. These approaches can be classified into three groups: (1) profile and checklist methods, (2) numerical ranking (scoring) methods, and (3) decision-making models. Most of these methods have shortcomings. Considering the fact that most of the specifications of mineral deposits, such as dip and depth, are linguistic variables, absoluteness of the explaining parameters by previous methods can be mentioned as the most important disadvantage of these methods. This paper discusses the Fuzzy technique for order performance by similarity to ideal solution (Fuzzy TOPSIS) to determine the mining method. The fuzzy decision making (FDM) software tool is employed to develop a Fuzzy TOPSIS based model. Application of this model with various values (crisp, linguistic and fuzzy) of the deposit eliminated the existing disadvantages of other methods. Two empirical illustrations demonstrate the effectiveness and feasibility of the evaluation procedure. These show that the proposed model performs better than its alternatives. Keywords: mining method selection, fuzzy TOPSIS, decision making, mining engineering, linguistic variables.

Jan 1, 2008

Good morning ladies and gentlemen. It gives me great pleasure to talk to you today about a pet subject of mine, on when to mill and when to leach gold ores. According to Gold Fields Mineral Services of London, gold production in the United States in 1989 amounted to about 8.5 million ounces (259t), an increase of 29 per cent over 1988 and 67 per cent over 1987. The U. S. Bureau of Mines reports that from the major producing states of Nevada, California, Montana, and Alaska, some3.2million ounces of the 1989 production were produced from milling gold ores and 2.3 million ounces from heap or dump leaching. Ap- proximately 45 million tons of ore were milled and 140 million tons of ore were heap or dump leached.

Jan 1, 1991