Search Documents

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation. In 1981, the production of sand and gravel totaled 755 million tons valued at $2.3 billion. California, which leads the nation with more than 110 million tons, together with Alaska, Texas, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No. 4 sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm (3 ½ -in.) maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Portland Cement Concrete Aggregates Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15-20% water, 7-14% cement, and 66-78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman, 1956). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.003 in.), uniformly coated and mixed with asphalt produced in the refining of petroleum. Except for the addition of mineral filler, sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement concrete aggregate. General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles which are sound and durable. Soundness and durability are terms used to denote the ability of aggre- [ ]

Jan 1, 1983

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954

By T. M. Geffen, F. F. Craig

Laboratory model flow tests have been made to simulate field conditions of partial pressure rnaintenance by dispersed gas drive on rocks having sandstone-type porosity. In this production method there is a significant saturation gradient between injection and production wells. A means of calculating relative permeability characteristics. from partial pressure rnaintenance flow tests has been developed. This method takes into account the saturation gradient. These kg/ko characteristics are identical to those for solution and external gas drives. This method of calculation, which has been proved experimentally, has limitations; however, it is valid for cases likely to be encountered in field prediction of partial pressure maintenance performance. The production performance of a hypothetical reservoir has been calculated for several different injection programs, involving both full and partial pressure maintenance. Results indicate that the maxinum oil recovery by these gas injection programs is obtained by full pressure mainte- nance at the original bubble point. Correspondingly lower oil recoveries are obtained by postponing gas injection and/or by reducing the degree of pressure maintenance. INTRODUCTION Dispersed gas injection is an important method of recovering additional oil beyond that obtainable by pressure depletion alone. The injected gas acts as a source of additional energy to displace oil from the rock formation as well as to retard oil shrinkage in the reservoir. In practice, gas injection is usually started after the reservoir pressure has fallen below the original bubble point. For various reasons sufficient gas is generally not injected to completely maintain the pressure in the reservoir. So, injecting gas at a declining reservoir pressure results in a combined external and solution gas drive. These two oil displacement processes are characterized by different gross saturation distributions in the reservoir. The external gas drive, like all frontal drive processes, inherently results in an oil saturation which increases from the injection wells to the producing wells. In the solution gas drive there is essentially a uniform oil saturation throughout the reservoir, provided the field is being depleted uniformly. It has been customary to predict oil recovery performance under partial pressure maintenance by a method which does not take into account the saturation gradient1. It has been shown2 that neglecting the presence of a saturation gradient can cause considerable error. It is the purpose of this paper to develop and present an improved method of predicting partial pressure maintenance performance of reservoirs including, where necessary. the effects of well arrangement. From the laboratory standpoint, this problem involves the measurement of the basic flow behavior (relative permeability characteristics) under partial pressure maintenance conditions. Recent research- as shown that for rocks having sandstone-type porosity, the relative permeability characteristics are identical for solution gas drive and complete pressure maintenance external gas drives. Since both solution and external drives have the same basic flow behavior, it was speculated that partial pressure maintenance, being a combination of the two, would also

Jan 1, 1957

By S Hughes

The smelting of concentrates and secondary materials has been subject to increasing challenges in recent years due to declining grades of feed materials, increasing impurity levels and ever more stringent environmental regulations. In addition there has been a growing focus on maximising the efficiency of energy usage and recovery of values. New opportunities have been created with rising metals prices and improved systems for the collection of secondary materials, giving rise to a need for more flexible process solutions.This paper focuses on a number of specific cases where a process solution has been developed using the Outotec« Ausmelt Process to meet particular feed material challenges and overcome limitations inherent when employing traditional pyrometallurgical processes.The first case involves the development and commercial implementation of a smelting process to recover values from zinc smelting residues typically deposited into dams as a waste product. The second case describes the application of the Ausmelt process for the smelting and converting of secondary copper feed materials, including e-waste. These materials contain a wide range of metals and plastics and need to be processed appropriately to maximise the recovery of values whilst avoiding environmental problems. The third case study covers the smelting of nickel concentrates containing elevated magnesia levels as well as nickel bearing catalysts with high alumina content, neither of which can be readily processed when employing traditional pyrometallurgical technologies. CITATION:Hughes, S, 2013. Pyrometallurgical process solutions for complex raw materials, in Proceedings MetPlant 2013 , pp 519-530 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Herbert A. Stein, John B. Murdock

Perlite is a natural volcanic glass which expands into an insulation material upon the application of heat. This paper discusses the operating characteristics of eight different types of furnaces for the expansion of perlite. It also includes a section on the theory of perlite expansion which serves as the basis for the authors' analysis of the furnaces.

Jan 1, 1950

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips, David G. Barker

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented.These results show that single sensor analysis information from the surface vibration system can be used as soft sensor inputs for monitoring process variables such as mill load that until now, have not been reliably measured. System outputs also show considerable promise in the area of condition monitoring. An example of the signal analysis output is presented showing elevated vibration levels in an area with higher resultant wear. Eventually, it is considered that outputs from this system for process variable and wear condition monitoring will be key new inputs to an online AG/SAG mill monitoring and control system."

Jan 1, 2003

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

The Electricity Generating Authority of Thailand own and operate an opencut mine supplying coal to on-site power stations at Mae Moh, 600 km North of Bangkok. The mine is being expanded from an annual production of 1.5 million tonnes per year in 1982 to over 9.5 million tonnes per year by 1991. The mine will be amongst the largest open pit operations in the world. It is technically difficult to operate and plan due to complex geology, weak strata and surface constraints including reservoirs, forests and traditional villages. This paper presents a case study of mine planning for the above project including associated collection and processing of geological and geotechnical information. The existing operation is described, as well as the strategy adopted for the mine at expanded production. The planning covers various phases of mine planning including a Conceptual Study, a Definitive Study and detailed short term planning. Each stage incorporated new information and reflected a higher level of confidence in the data and resulting plan. Sophisticated computer techniques were required including geological modelling, calculation of volumes, geotechnical analysis, scheduling and costing. The planning was undertaken on site by a team of Australian and Thai Engineers as part of the Thailand-Australia Lignite Mines Development Project which is a four year programme of assistance funded by the Australian Government.

Jan 1, 1986

BLAMEY STEVENS, Nogales, Ariz. (written discussion *).-This subject should be approached boldly from the purely physical standpoint. There are usually many known ways of making chemical deposits of any particular mineral and probably many more ways that are still unknown. With-physical-effects; .however, there-are, in-general, only one or two, or possibly three, ways that will pass muster before the physicist, when he realizes the geological conditions to be harmonized with the physical ones. Let us consider the second way that Mr. Taber describes: "It (the mineral matter transported in solution) may enter along a fracture, bedding plane, or similar passage, and, as it is deposited, force the wall rock apart, thus making room, for the growing vein," because it is the one Mr. Taber chooses for the great bulk of metalliferous veins. By "forcing the wall rock apart" Mr. Taber indicates that he means that the process of crystallization or-solidification of the mineral in the vein forces the walls apart. To prove this, he offers a great variety of geological evidence, which, from the physical standpoint, is entirely superficial. From the geological standpoint the evidence is the best to be had, but it is entirely negative and one single grain of really positive evidence will entirely offset it. Suppose it be granted that there is a considerable force of crystallization. It is well known among physicists that, other circumstances being equal, the crystal would rather form where it does not have to exert that pressure; or, to be more exact, where it is not necessary for the crystal to

Jan 12, 1918

By Laís Ávila de Oliveira Silva

A aplicação de ligas de NiTi como biomateriais exige que sua superfície tenha um excelente acabamento final, para garantir a alta resistência à corrosão e a biocompatibilidade. O polimento eletrolítico é um processo capaz de diminuir as imperfeições da superfície, sem alterar as propriedades do material, e de formar uma fina camada protetora de TiO2. Nesse estudo, foram realizados eletropolimentos em fios superelásticos e com memória de forma, usando dois eletrólitos ácidos distintos. A partir dos resultados obtidos, foi possível concluir que a solução de ácido sulfúrico produz superfícies mais homogêneas do que o de ácido perclórico, para os mesmos tempos de polimento, e se apresenta como uma boa alternativa para o tratamento superficial de ligas superelásticas e martensíticas de para sua aplicação como biomateriais.

Aug 17, 2017

By Richard H. T. Garnett

Large scale, profitable, offshore mining of cassiterite started in 1907 around the coast of south Thailand and continues today in Indonesia. The more complex marine mining of diamonds commenced in the early 1960?s and is now an established industry off the coast of Namibia in southern Africa. The activities have involved many diverse organisations, and have required the development of new marine mining equipment. De Beers Marine, more recently as contractor to Namdeb, has been the dominant producer since 1989. Smaller, public, mining companies, registered in South Africa, Canada and the U.K., have achieved mixed performance results, but the total annual revenue from offshore diamonds now exceeds about US$ 180 M. With the benefit of hindsight, there are some useful lessons to be learned from the experiences. Mining of placer deposits at sea is more difficult and more costly than on land. It justifiably commences in response to a market demand for a product that cannot be supplied in sufficient quantity from onshore sources, not because the marine resource exists. The high costs can be offset in places by submarine grades so high that they have not been seen on land for a century. Technical and commercial success requires a combination, and a sufficiency, of ore reserves, capital, experienced people, and technology. Economic viability is not achieved easily and some diamond mining companies have experienced a very short productive life, terminating in their acquisition or liquidation. The reasons for failure in marine mining, regardless of whether the product is diamonds, gold, or tin, invariably are similar and fall into two categories. Those outside a company?s control include the sea conditions, taxation and fiscal climate, security of lease tenure, and the diamond market. The others, assignable to the company, provide important instructions for those who may aspire to advance the cause of marine mining.

Jan 1, 2004

Jan 1, 1949

During industrial copper electrowinning, a fraction of the electrolyte becomes entrained with the oxygen gas bubbles that are evolved at the anodes. The fraction of entrained bubbles increases from the bottom of the anode to the top, resulting in a bubble distribution that appears as an inverted wedge between the cathode and anode. Since the bubbles act as insulating spheres, electrolyte resistance increases from the bottom of the electrodes to the top resulting in correspondingly higher local current densities and uneven copper growth along the cathode. To counter-act the inherent tendency toward excessive copper growth near the bottom of the cathodes, the use of tapered anodes was examined. The potential improvement in cathode current distribution was evaluated by comparing the primary current distributions for 2-D computer models of a copper electrowinning cell with plate shaped anodes against one with tapered anodes.

Jan 1, 2007

By M. G. Ayat

A novel tracing technique employing specifically prepared trace particles has been applied to coal preparation separatory systems. The technique employs individually prepared trace particles representing specific known sizes and densities of coal particles. These trace particles are injected into the feed, to the processing circuit, and are then detected at locations in the coal product and refuse streams. It is anticipated that on-line input of the generated partition data will be linked with computer technology to provide rapid analysis of the processing efficiency, and to allow for process control. This tracing technique can revolutionize many processing operations from the diagnostic viewpoint as well as from the coal processing standpoint.

Jan 1, 1986

"En 1953, se habilita la nueva planta de flotación de cobre en Paragsha, donde el funcionamiento de las soleras tipo Lorain y la producción del mineral pirita lograron buenos resultados. Empero las nuevas condiciones de proceso, limitaron su funcionamiento y costo. Por tal motivo, el objetivo del trabajo se basa en la construcción de una solera de mayor rendimiento y menor costo, modificando su diseño al de una honda contínua. El primer juego de este diseño fue instalado en el molino de cobre Nº 1, sin aún obtener el dato final sobre su rendimiento. Posteriormente se consideró la solera AMSCO, dado que el diseño fue más eficiente y el costo final por tonelada fue menor. Sin embargo, se encontró que el contorno del valle era muy cerrado y las bolas N°4 se alojaban de modo ajustado, formando una solera muy gruesa. En consecuencia, se construyó otro diseño denominada ""Solera de onda abierta contínua"", el cual fue instalado en el molino de cobre N°7, donde la capacidad de molienda es igual de óptima y los costos son menores. Así, se pensó que la solera de una sola honda, es mejor que la de onda contínua puesto que este diseño tiene una sola honda en el centro de cada plancha de la solera. Luego, se diseño un tercer diseño, donde el promedio de vida era mejor. Por ello, de los tres diseños a seleccionar -la solera Lorain con 10 hondas, la solera de una honda con 20 hondas y la solera de honda continua de 30 hondas -, la última demostró ser la más eficiente. De otro lado, se probaron otros diseños de honda contínua con distintas aleaciones como el ""Nihard"", cuyo promedio de vida es entre 14 y15 meses aproximadamente, con el tonelaje actual de aproximadamente 270 000. Concluyendo que la experiencia anterior con solerasNihard en molinos a rodillos de 4 pies de diámetro, el impacto es mayor, obteniéndose en quebrantamiento de soleras a 3/4 grosor, pero que pese a esto, resulta ser superior a cualquier otra solera usada actualmente y en eñ que Paragsha esté 100% con soleras de molinos Nihard, a excepción de las rejillas dada su fragilidad. "

Jul 20, 1957

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

The beginning of Colorado's mining industry is linked on one side with that of the Appalachian districts and on the other side with that of California, because the first discoveries were made by pioneers when on their way from Georgia to California. In the summer of 1849 a party of seven Georgians were taking a herd of thoroughbred horses across the continent to the Pacific coast. They reached Camp Lyon, on the Arkansas river, in October, and, meeting James Dempsey, a Government guide, they were persuaded by him that it was too late to cross the mountains that season. His advice was accepted, and, moving northward, they established a winter camp at the junction of Cherry creek with the Platte, close to the site of the city of Denver. Upon a sand-bar, lining the south side of the river, they built two cabins. During the closing months of 1849 they prospected the alluvial banks of Cherry creek, but they made no attempt to penetrate into the mountain canyons, near them, westward, for fear of the Indians.* They found gold in several places along Cherry creek, and particularly at a spot 16 miles up the stream from their camp. From the feathers of the wild geese that they shot they obtained quills in which they placed their gold-dust. This party of Georgians consisted of Dr. L. J. Russell and his brother, Green Russell, also A. T. Lloyd, G. W. Kiker, and P. H. Clark. Early in 1850 they crossed the main range of the Rocky Mountains by the Bridger pass and went on to California. They mined near Downieville, and were successful. Occasionally mention was made by them of the gold

Jan 1, 1932

By Lloyd Litwin

The ARTA 2008 Project (Alpha Ridge Test of Appurtenance) was a Canadian Government sponsored deep water seismic survey carried out on the high arctic permanent polar ice cap. This Geological Survey of Canada operation was the second seismic research project in the high Arctic and was monitored by the Danish Government. Utilizing 100% air support from Eureka and then helicopters from an ice based tent camp north of Ellesmere Island, the five week study was accomplished in the early spring just after the sun returned to the far north.

Jan 1, 2011