Search Documents

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By M. J. Ankeny

Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the prevention of such accidents will materially improve progress in safety in the coal-mining industry. Beginning March 1950, Federal coal-mine inspectors were made responsible for completely investigating all fatal accidents in and around coal mines. During these 10 months, Federal coal-mine inspectors investigated 447 fatal accidents. This is a study of 121 of the fatal haulage accidents investigated, which constituted 27 percent of fatalities from all causes. Haulage employees represent only 12 to 15 percent of mine personnel, but, on the basis of accident frequency, their work is the most hazardous in coal mines. Fatal haulage accidents occurred in 53 bituminous coal-producing counties representing 14 States and Alaska. The physical conditions represent a cross section of' producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of modern mechanized mines.

Jan 1, 1951

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By Oswald J. Heinrich

This question having been repeatedly raised, and particularly revived in a discussion at the last meeting of the Institute, I beg to submit the following remarks, based partly upon personal experience, partly upon the results of large works in Europe, establishing, years ago, the practicability of certain methods, which may therefore be considered to have passed the stage of mere experiment. Before entering upon the merits of one system or the other, it is indispensable to lay down some recognized principles, which ought to serve as guides, in arriving at fair judgments in questions of this character. In a profession like that of mining, locally so much influenced by combinations of circumstances too various to mention, it is difficult to do more than lay down the main features of a system based upon general laws and recognized facts, leaving the details to the sound judgment and experience of the engineer, who, by virtue of his education, ought to be able to make such choice and such modifications in the plans of a mine as the particular case demands. Mineral resources, in some countries the sole property of the owner of the soil, in others controlled by the strong hand of a government, are nevertheless a gift of nature, in which, indirectly, the whole of the human race has as real an interest as the immediate owner himself. This interest requires, at least, that no unnecessary waste of

By Jack G. Croeni

The Bureau of Mines developed a method to extrude low-density tungsten powder billets into rods and sheet bar with high-energy-rate forming equipment. Billets were compacted and sintered in an atmosphere of hydrogen to obtain a density of approximately 60 percent. Extrusion was conducted at reduction ratios of 6.25 to 1 and 9 to 1 at 1,800° C to prod e high-density, sound material. Yield strengths obtained were higher than those of material produced by conventional powder-metallurgy techniques, but ductility was lower at high temperatures.

Jan 1, 1966

By Wilhelm Schwarz

Manganese nodules lay in vast areas of the deep sea floor. Ideal harvesting conditions for a manganese nodule field are dense nodule abundances of nodules between 20 and 60 mm diameter and a metal content as high as possible. With regard to the development of collector technology, the properties of the deep sea soil, in which the nodules are embedded and to which the nodules stick, are of major interest. The forces for loosening the nodules have to be provided by the collector. For this purpose water jets and/or mechanical devices can be employed. For the choice of the best collecting procedure, various criteria, such as collecting rate, energy consumption and the environmental impact on the eco system of the deep sea floor, have to be considered and weighted as to their importance. Nowadays, the concept of a mining system with a flexible transport hose and a self propelled collecting machine is increasingly accepted among the expert community. With regard to the trafficability of the deep sea soil with a self propelled mining machine, the mechanic properties of the soil and the morphology of the deep sea floor are of special importance. The manganese nodule fields, which are interesting with regard to their recoverability, are mostly in the areas of tectonic fracture zones, at which the morphology of the sea floor is formed by vulcanic activities. In these areas, deep sea mountains, pits and other obstacles exist that have to be driven around if not trafficable.

Jan 1, 2003

By Philip Wilson

Tun mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic limestones of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft. the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances away from the zone of contact metamorphism.

Jan 7, 1916

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

Geological Survey topographic mapping parties started initial operations in the 1953 Alaskan mapping program. One area to be covered is 17,000 sq miles in the Kantishna River, Melozitna, Tanana Fairbanks, Healy and Mt. McKinley section. The other area to be covered is the Kenai, Tyonek, Blying Sound and Seldovia areas. Average starting salary earned in 1952 by Columbia University School of Engineering graduates was $4000 yearly. This year's graduates can expect to start at about $4300, according to a survey taken by Columbia. Figures cover only those with Bachelor degrees. Graduates with a Master's started at an average of $500 per year more.

Jan 7, 1953

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By Richard J. H. Barclay

The Lac Otelnuk iron property is located in the Province of Québec in the Northern Labrador Trough. The Labrador Trough is an extensive geosyncline of Proterozoic rocks, unconformably underlain by Archean gneisses. The Lac Otelnuk iron property hosts two significant magnetite iron-formation taconite deposits that outcrop, are sub-horizontal and are known to extend for at least 25 kilometres along strike. The host sedimentary rock package that includes a cherty iron formation is weakly metamorphosed to greenschist facies.

May 1, 2007

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By Otis W. Freeman

Production of oil in Indiana during 1944 is estimated at approximately 4,950,000 bbl., a decline of 6 per cent from the preceding year. Shortage of labor and material, together with governmental regulations resulting from the war, largely account for the drop in output and limited new developments. Three new pools were discovered in the state during 1944. Two of these, New Harmony, South, and Hovey, West, are in Posey County. Six wells in the New Harmony, South, field produced 66,422 bbl. of oil last year. A third field, Cato, in Pike County, did not market the oil from its discovery well during 1944. Several wells discovered oil in the Henderson field of Jay County along the Ohio state line. An important south extension of the St. Thomas field in Knox County was discovered during the year. Active drilling took place in the Inman, East, and Upton fields, Posey County, both discovered in 1943. Twenty-two wells in Inman, East, produced 151,1gr bbl. in 1944 and 12 in Upton produced 107,052 bbl. Owensville, and especially Owensville, North, in Gibson County, made large gains in production as a result of active drilling. The Dodds Bridge field in Sullivan County continued good production from deep sands reached in 1942. The Griffin continued to be the largest producer among the oil pools of Indiana, accounting for 2,004,180 bbl., over 40 per cent of the state's output. The next largest producing fields are Mt. Vernon and New Harmony, both in Posey County. The largest gas well brought in during 1944 was in the Rockport field, Spencer County, and had an initial output of 2,680,000 cu. ft. per day. The most productive gas fields in Indiana are Rockport, Spencer County, Greensburg, Decatur County, and Unionville, Monroe County. Total production in the state is . hard to estimate, as considerable gas is consumcd in farm homes and for other local uses, and never is reported, but was near 1500 million cubic feet. Some oil from the Trenton field is also used locally and is unreported from pipe-line runs. A total of 606,145 ft. of new hole was drilled in Indiana in 1944. Most of the completions were in Posey and Gibson counties, although wells were drilled in 36 different counties. During the year 331 wells were completed. Of these, 145 found oil in commercial quantities and 28 were gas wells. The initial production of the 145 oil wells was 11,908 bbl. per day. Settled production would be less, of course. The largest wells reported during the year were two on the J. W. Mann farm, in the Mt. Vernon field, with a flush flow of 500 to 800 bbl. each.. Six pools, all small "one well" affairs, were abandoned in 1944; i.e., Fleenor and Patoka in Gibson County, Grafton and Rapture in Posey County, Vaughn in Vandei-bwgh County and Millersburgh, Warrick County.

Jan 1, 1945

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By William Petruk, Donald Leroux, Michael Cooper

"Brunswick's primary flotation circuit (CuPb) produces a low grade concentrate containing considerable amounts of undesirable sphalerite and pyrite. To determine the cause of the poor selectivity, a series of Quantitative Mineralogical Analyses (QMA) were performed on several CuPb circuit streams. It was observed that significant fractions of sphalerite and pyrite reporting to the concentrate was liberated, meaning that their depression was not complete. The study highlighted the need for some R&D efforts to be spent in sulphide flotation fundamentals.IntroductionThe viability of many mining projects strongly depends on the performance of their concentrators. More than ever, competitive grade concentrate and high metal recoveries are criteria of paramount economic importance. The selectivity of solid/solid separation processes used in concentrators must be maintained at high levels or continuously improved.Flotation is the solid/solid separation process used by most base metal producers. In spite of its low operating cost, flotation remains a very complex process. To make it selective, precise reagent dosages and electrochemical conditions must be maintained. The difficulty in controlling flotation lies in the numerous heterogeneous reactions that can take place between the different solid, liquid and gaseous phases involved. This complex chemistry makes flotation selectivity difficult to understand and, therefore, to improve from a theoretical point of view.Brunswick Mining and Smelting, near Bathurst N.B., operates a 10500 tpd concentrator which produces four concentrates through five stages of sequential flotation (Figure I). Various reagents are added at key process stages while the ore undergoes different electrochemical conditions. Although the selectivity is important at all stages, the performance of the very first separation, the CuPb circuit, is the most critical. It is here where mineral misplacement to the wrong stream has the greatest economic consequences."

Jan 1, 1996

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954