Search Documents

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker' measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-' sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"' which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963

By J. M. Rios

Without conscious effort and understanding, a number of factors peculiar to mineral exploration campaigns conspire against building sustainability in host communities. These include the episodic and transitory presence of an exploration team in the community and the inherent uncertainty of outcomes; most projects fail. Given these circumstances, there is a strong tendency to apply a simple formula of providing employment, pragmatic philanthropy and supporting infrastructure improvements (roads, schools and clinics) to demonstrate that mining provides benefits. Experience in rural native communities of Mesoamerica has shown that it is possible to create positive, sustainable outcomes quite rapidly within communities, which build capacity, improve quality of life and support a strong social license to operate. Success comes from an understanding of community structure and dynamics; engaging with all segments of the community; creating healthy, transparent and accountable relationships based on clearly defined roles and responsibilities; and supporting and strengthening the role of women in a culturally appropriate way. To this are added innovative and culturally appropriate ways of incorporating sustainability through genuine social investment in areas more typically addressed by exploration companies; health, education, and environmental management.

Aug 1, 2013

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By J. G. Donaldson

Nickel containing less than 0.01 percent of total metallic impurities was produced at the Rolla Metallurgy Research Center of the Bureau of Mines by electrodeposition from purified electrolytes. The first report on this research4 described purification of electrolytes by selective precipitation and by liquid-liquid extraction. This second report describes a procedure: or electrodepositing high-purity nickel from electrolytes purified by passing a nickel ammine solution through a column of an ion exchange resin. The nickel electroplated directly from the ammine solution without further treatment; a titanium cathode and two platinum anodes were used. The nickel deposit was dense, smooth, and adherent, and contained less than 0.001 percent each of cobalt, copper, and iron, and spectrographically detectable traces of aluminum, magnesium, and silicon. Nonmetallic impurities in the nickel metal were carbon and sulfur, each present in concentrations of less than 0.01 percent. The results of several experiments planned to purify solid nickel salts by zone refining are also reported. These salts, after purification, were intended for use in preparing electrolytes for deposition of high-purity nickel. Results were not encouraging so that the more promising ion exchange procedure was emphasized chiefly.

Jan 1, 1962

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By M. E. Wadsworth

The region about the south shore of Lake Superior is to geologists one of the most interesting districts of the United States, embracing as it does, in a limited area, old crystalline rocks, together with forms that are almost in their original condition of a beach sand and mud. In this region was first established the base of the geological column, the Azoic (" without life") System of Foster and Whitney, or the Archæan (" the beginning ") of Dana. Overlying this system are found the sandstones and limestones of the Paleozoic (" ancient life "), and their associated lava-flows (Algonkian ?). These systems possess a strong economic interest, owing to the stores of iron in the Azoic and of copper in the Paleozoic or Eozoic of this district, which forms one of the most important mining regions in America. The geology of this section is so difficult and complicated that, in its general discussion, perhaps no proposition can be stated concerning any portion of it to which exceptions cannot be taken. Indeed, out of the general discussion of different points comes in time the truth, and various geologists, even now, are working over this region in the endeavor to arrive at some consensus, or at least to determine upon what points they can agree, and upon what points difference of opinion will have to exist between them at present, until further evidence can be obtained. The writer will endeavor to give in a brief form that which appears to him at present to be the most correct statement of the geological structure of the region, admitting that from time to time, as more complete evidence shall be obtained, he expects to change his views in the future, as he has done in the past, if that evidence shall cause him to believe that he has been mistaken.

Jan 1, 1898

By O. J. Kensok

THE literature contains three previous studies of the chemical activities of Cd-Mg alloys: Trumbore, Wallace, and craigl obtained chemical activities of magnesium at 543" by performing electromotive-force measurements; Borg and irchenall calculated activities at 590°K based on vapor-pressure measurements of cadmium over Mg-Cd alloys by the Knud-sen effusion method; and Terpilouski and arcka measured the chemical activities of magnesium in the liquid state by means of electromotive-force measurements. In this study the vapor pressure of cadmium was determined over nine solid Cd-Mg alloys in the temperature range 571" to 697°K by the Knudsen effusion method. This study was prompted by the lack of precision in the data reported by Borg and Birchenall. Knudsen cells used during this study were fabricated from 0.020-in.-thick tantalum tubing. The tops and bottoms of the cells were cut from 0.010-in.-thick tantalum sheet, press-fitted, and welded in place. The orifice was drilled in the cell top and subsequently reamed to a knife-edge thickness. The diameter of the orifice was measured with a traveling microscope capable of reading 0.0001 cm. The sample was heated by means of a resistance

Jan 1, 1967

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99· 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman's2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman's method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman's2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

The reasons for selecting two stage pebble milling in preference to conventional methods of grinding are discussed. Commissioning of the first section was completed in October, 1969. Improvements in both the operating and engineering aspects were then incorporated in the section commiss ioned in March, 1971.

Jan 1, 1975

By E. J. Freech

In this part of the two-part paper we discuss briefly the adaptation of the comminution model to describe the observed behavior of an industrial grinding circuit. Although reported verification of comminution models for continuous systems is limited, some interesting work has been reported 1,2 recently. The data acquisition and modeling efforts are described first, followed by discussion of some of the simulation results. Observations pertinent to steady-state operation are presented followed by a description of the application of a dynamic model of the grinding circuit for synthesis and evaluation of grinding-circuit control. The pilot-scale work indicated the comminution model should be capable of describing an industrial size-reduction process. Recognizing the broad utility of a process model based on first- principles, the Industrial Nucleonics Corporation of Columbus, Ohio, embarked on a joint program with the Duval Corporation of Tucson, Arizona, to evaluate the industrial applicability of the models described in Part I. This program was conducted in a grinding circuit, which included a rod mill 12.5 feet in diameter and 16 feet long and a ball mill 12.5 feet in diameter and 14 feet long, at Duval Corporation's Esperanza property3. The rod mill was operated in open circuit and the ball mill in closed circuit with cyclone classifiers.

Jan 1, 1970

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By Don Opacic

The disposal of sludges and other similar industrial wastes is a major problem. Liquid wastes from industrial operations, when treated, produce significant volumes of sludge which are difficult to dispose of, because of the chemical and physical properties of the sludge. In the mining industry sludge is produced from various water treatment operations, in particular mine drainage neutralization. Waste water from coal preparation plants also produces a sludge however the sludge is in fact a slurry containing clays, coal fines and coal impurities. In many areas the disposal of these sludges is producing a serious problem. Mine drainage sludge consists of a variety of hydrous iron oxides, usually ferric oxides, contaminated with other neutralization products such as calcium sulfate. The volume of sludge from mine water or mine

Jan 1, 1973

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

Nickel WestÆs Kalgoorlie Nickel Smelter operates three Peirce-Smith converters, each processing 110 tonnes of matte per charge. The vessels are lined with chrome-magnesia refractory with a mouth traditionally constructed from steel liner plates, protected with cast refractory. Mouth refractory is damaged by molten material and the action of cleaning solid buildup off the mouth. Once damage has accumulated, the mouth must be frequently maintained with hot refractory gunning or a mouth leak may occur. Such a leak requires a 32 hour repair period. A converter mouth redesign program was undertaken with the aim of reducing the rate of mouth damage during operation, eliminating mouth leaks and shortening mouth replacement times during vessel rebuild periods. An overview of the redesign process and operational performance is contained herein.

Jan 1, 2005

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for concerned people. The coal industry has taken great measures to reduce pollution. With the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. Furthermore, eliminating thermal drying completely by using centrifugal dryers (Bird screen bowls) to dewater fine coal products and meet consumer specification has completely eliminated air pollution. The coal industry is taking steps to eliminate stream pollution and the hazards created by tailings ponds. These plants are closing their water circuit by recovering all solids in solid-bowl centrifugal equipment. In doing this effectively and economically the water discharged into the streams does not contain any refuse solids. This provides a safe economical method.

Jan 1, 1976

By M. L. McAllister, M. Veiga

The mineral industry has seen many significant changes in the past decade. Increasingly, it has responded to unanticipated pressures and demands with a variety of voluntary initiatives. Yet there is still much to do. Mining now takes place in a different context than was the case in the past. Socio-economic, political and environmental considerations must now be integrated into traditional mining systems. This process of integration needs to involve industry, governments, academics, communities and other stakeholders to design a new approach to mining, one that can be fostered through interdisciplinary links and holistic strategies. This paper considers the meaning of sustainability in the context of the Canadian mining industry and explores the need for a broader vision for the mining industry. The role of technology is then analyzed and related to an initiative recently taken by Canadian universities to develop a national network for interdisciplinary research into sustainable mining, CaSM.

Jan 1, 1999

By D J. McDougall

Due to changes in the solid-state conditions of minerals in the rocks surrounding hydrothermal, contact meta-somatic or metamorphosed ore deposits, positive or negative thermoluminescent anomalies may be found in their vicinity. Several types of equipment which can be used for both quantitative and semi-quantitative measurements of the emission are discussed and compared. Methods of selecting, preparing and testing samples to ensure reproducible results are outlined, along with the kind of data which can be obtained from different types of equipment. The normal thermoluminescence of rock-forming min~ erals in the common rock types is noted, and variations in the solid-state conditions in the wall rocks which will cause marked increases or decreases of true thermoluminescence are outlined, as well as the thermolum-nescence-like emissions which are present in the vicinity of ore deposits. Introduction T HERMOLUMINESCENCE occurs when certain crystalline materials are heated to temperatures ranging between 180' and 400°C. The light emission can be ascribed to the release of electrons metastably trapped within the crystal lattice, with peak emissions taking place at temperatures which are more or less specific for a particular set of traps; the area under

Jan 1, 1965

By Thomas T. Read

Mining, which is at least twenty cen-turies old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation, for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography, recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of 'loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, clearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, becadse a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. Professional Development In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic education. The contrast is almost as great as between

Jan 1, 1943

By E. Tulcanaza

The practical significance of the in situ grade variability is usually neglected. Although recognized, often times it is either ignored or just considered as a vague guideline in many of the decisions dealing with exploration, reserve estimation, and mine planning. This paper stresses the significance of grade variability for exploration and mining, and illustrates its liaison to the structural features of the ore deposits, as well as to the mining parameters used for mine extraction. Some geostatistical results obtained from a silver mine, tungsten mine, and copper mine in South America are discussed.

Jan 1, 1985