Search Documents

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

By Alastair Torrance, George Boucher, Roger Keller

An investigative blast programme has been carried out to provide information on the best blasting methods to excavate Chek Lap Kok island in Hong Kong for the new airport. The objectives of the programme included the assessment of a range of blast design parameters and their influence on fragmentation. This has been evaluated by physical assessment, photo digitising of the muckpile and computer predictions. In addition, a model to predict the three dimensional muckpile shape has been successfully calibrated.

Jan 1, 1992

By Leo A. Schrider

A prediction for oil recovery from a pilot waterflood in the Kane oil- field, located in Elk, Forest, and McKean Counties, Pa., was made and compared to actual field performance. Water-injection and production histories, well logs, other field data, and results from laboratory tests of core material were used in this analysis. Performance of the pilot waterflood, initiated in January 1963, was predicted using a modified Craig, Geffen, and Morse calculation technique. Maximum recovery from this low permeable, preferentially oil-wet formation was predicted to be about 22,500 barrels of oil after 300,000 barrels of water had been injected into the pilot waterflood area. After additional field data were collected it became necessary to reevaluate the pilot waterflood area. The gas saturation prior to the waterflood was estimated to have been 20 percent, based on an assumption regarding the required volume of water injected to initiate oil production. In view of the actual field performance, a gas saturation of 13 percent is indicated. When this gas saturation and the method originally proposed by Craig and others are used) the predicted results are more representative. In December 1965, field performance was further analyzed using a hyperbolic-decline curve as presented by Arps. Based upon this evaluation method, the pilot water flood in the Kane sand should produce 37,000 to 42,000 barrels of oil with the injection of 300,000 barrels of water into the pattern. By continuing this secondary-recovery project to a reasonable economic limit, ultimate oil recovery may be as much as 50,000 to 55,000 barrels, or 129 to 142 barrels per acre-foot from 36.5 acres.

Jan 1, 1967

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998

By Xavier B. Starnes

"INTRODUCTION The Krausse Estate property was the site of the first lead silver mining in western Kentucky, which began with the sinking of the Andrew Jackson shaft in 1835 3/. The earliest miners considered fluorspar of no value and threw it upon the waste dump, but Crittenden County later became an important part of the western Kentucky and southern Illinois fluorspar district 4/, which has produced about 90 percent of the fluorspar mined in the United States. By 1945, approximately 35,000 tons of fluordpar ore had been produced from the Estate property.This property can be reached by traveling west from Marion on Highway 60 from 2.5 miles, than northward 3 miles. The road from the paved highway to the mines is very rough but not impassable even in bad weather. Ore is hauled 5 1/2 miles by truck to custom mills at Marion, a town of 2, 000 population, where the Illinois Central Railway was a freight station.Hurricane Creek runs through the eastern part of the property. The surface slopes steeply upward to west from the creek, and the topography is rough. The top of the hill is about 150 feet above the creek.The climate permits working throughout the year, but spring rains cause surface water to enter mine and water apparently drains southward along the fractured fault zones, so that when no water is being pumped at properties north of the Krausse Estate a heavy flow comes on the Krausse."

Sep 1, 1946

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines fired seven test blasts in a 22-ft bench of limestone, screening the material to investigate the influence of explosive type and between row delays on fragmentation. Four 4-hole, single-row test shots were conducted evaluating dynamite, ANFO, emulsion, and a 60-40 emulsion-ANFO mix. Three 12-hole shots, with three rows of 4-holes, evaluated delays between rows of 24, 36, and 120 ms. Accurate in-hole electronic delays were used, firing within 1.5-ms of the nominal delay. All seven shots had a 6- to 7-ft burden, 10-ft spacing, with a hole diameter of 3-1/2 in fired on a 12-ms delay between holes in the row. The tests were instrumented with strain gauges grouted in the burden region examining stress wave and gas pressure effects. Fiber optic probes were used to confirm timing and to obtain detonation velocities.

Jan 1, 1989

By Jeffrey L. Thompson, Kenneth A. Gutschick, Robert C. Freas, Robert S. Boynton

Lime, the "versatile chemical," is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or calcia, or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to much confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is usually made from high-calcium or high-magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high-calcium limes contain less than 5% MgO. When the lime is produced from a high-magnesium limestone, the product is referred to as dolomitic lime. Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 A.D. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from a scientific perspective. The production of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 15 to 20 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Calcination refers to a broad class of reactions, of which the lime/limestone reaction is just one, wherein a substance is heated to less than its melting point, resulting in a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [CaCO3 (limestone) + heat (1000° to 1300°C)= 100 CaO (quicklime) + CO2 T 5644 or CaCO3 • MgCO3 (limestone) 10084 + heat (900°C to 1200°C) CaO • MgO (quicklime) + 2CO2 T 56 4088] While there is nearly universal agreement about the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in Fig. 1. From this model it can be seen that calcination is a function of both temperature and CO2 pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the reaction interface must make its way through the lime to the exterior surface. Therefore, because calcination is limited by gas diffusion to the surface of the partially calcined limestone, natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in

Jan 1, 1983

By M. P. Nackowski, Armond H. Beers, W. T. Parry

Three hundred soil samples were collected on a one-mile grid in a 400-square mile area of the Oquirrh Mountains, Utah, including the Bingham-Lark, Ophir, Rush Valley, and Mercur mining districts. The soil samples were analyzed for copper, lead, zinc, silver, molybdenum, manganese, and iron by X-ray fluorescence using arsenic as an internal standard. Anomalies coincide in most cases with the mining districts. However, in the Mercur district no anomalies were detected. Also samples collected one mile from the Bingham mine barely reflect this major producer. No samples were collected within the Bingham mine area.

Jan 1, 1973

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By George S. W. Cumpston

El presente texto describe los factores que intervienen en la economía de la molienda con bolas, considerando la carga y calidades de las mismas. Para determinar cuáles son los factores en el estudio económico, es necesario conocer las cuatro calidades básicas de las bolas de las moliendas: las bolas de aleación de acero, forjadas y con tratamiento térmico, las bolas de acero al carbono forjadas y con tratamiento térmico, las bolas de aleación de acero fundido y las bolas de fierro fundido. Los productos fundidos generalmente no son tratados térmicamente y las bolas de fierro fundido son un producto de bajo precio y más ordinario. En este sentido, una bola tratada térmicamente sea en aleación de acero o de acero al carbono, tendrá una estructura granular más fina que las de los productos fundidos. Para fijar la economía de un tipo de bola, se utilizan dos formas de investigación: la prueba de bolas marcadas y la de resultados de producción, estableciendo esta última como la más exacta, aunque requiera molinos duplicados para medir su producción. Luego, se procede a experimentar con diferentes tipos de bolas -a través del costo de transporte y manejo requeridos para moler una tonelada de mineral- y asi determinar cuál es la bola más económica para cada operación. Posteriormente se evalúa la facilidad de la molienda y se delimita la carga de bolas que se aproxime mejor a la carga balanceada.

Jul 20, 1960

By Carl E. Swartz

ALTHOUGH a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. CHARACTERISTICS AND REQUIREMENTS OF SOLDERS IN GENERAL General Physical Properties.-When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.-The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

Jan 1, 1928

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By A. W. Davis

"The Red Rose mine is in the Rocher Deboule mountains about 8 miles east of Skeena Crossing and a like distance south of the town of Hazelton; the most northerly settlement on the Prince Rupert line of the Canadian National railway and 177 miles northeast by rail from Prince Rupert. The mine workings are on the north side of Balsam or Red Rose creek; a tributary of Juniper creek that drains via Kitseguecla river into the Skeena near Skeena Crossing. A truck road 11 miles long extends from Skeen a Crossing (elevation 650 feet) to the Red Rose mill (elevation 4; 100 feet). The mine workings lie between 5; 600 and 6; 300 feet above sea-level. Mine and mill are connected by a 1-mile aerial tramway and a tractor trail.The Red Rose claims were staked about 1910 by prospectors attracted to the district by the construction and near completion of the railway between Prince Rupert and Jasper. For a number of years interest centred in prospecting a sheared zone exposed in a ravine between elevations of 5,425 and 5,825 feet. Several adits were driven and some high gold assays were obtained in vein quartz in the sheared zone, but this work did not develop sufficient ore and the property finally closed down. In the early twenties of this century tungsten minerals were discovered in the northern extension of the vein, but nothing was done to test this deposit. Finally, in 1940, spurred by the wartime demand for tungsten, the Consolidated Mining and Smelting Company of Canada drilled the tungsten-bearing vein, and although results were none too encouraging, underground work was begun in June 1941. The latter work disclosed substantial amounts of ore. A small mill, subsequently enlarged, began operation early in January 1942 and by the autumn of 1943 some 1,194,000 pounds of tungsten concentrate had been recovered. Mining ceased in November 1943 because of orders from the Metals Controller that no more shipments would be permitted."

Jan 1, 1954

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. Louis,. Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 9, 1919

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By Markus Reifferscheid

Industry 4.0, Digitalization, Internet of Things (IoT) and Cloud Computing are predominant topics in the world economy at the moment. At the ABM week 2017 Dr. Markus Reifferscheid, Head of Research & Development of SMS-group, will talk about the proceeding digitalization in the steel industry with selected examples of SMS-group. He will present advanced concepts and solutions which are currently being developed.

Oct 30, 2017

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969