Search Documents

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By J Stiefenhofer

"*This is an abstract only*Construction of geological models for kimberlites has historically largely been based on visual volcanic textures and features, with chemical data only collected on an ad-hoc basis depending on the level of perceived complexity observed in the geological data. The focus of this paper is a high-level view of the impact an initial absence (or lack) of relevant chemical data had on two kimberlite resource models as well as how the magnitude of the problem increased once the resource estimation process commenced (Stiefenhofer, 2013). The impact of ignoring chemical data on a project assessment where micro-diamond estimation techniques are employed, is also discussed. Resource estimates based on micro-diamond data are critically dependent on the use of the correct geological model since stationarity of the size frequency distribution is key to the generation of correct grade estimates. A multilevel approach is advocated where the volcanological/visual model is verified using chemical data and both are in turn verified by the diamond data.CITATION:Stiefenhofer, J, 2013. The use of chemical and metallurgical parameters to enhance the economic value of kimberlite resource models, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 101-104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997

By Ronald A. Munson

Samples of the naturally occurring zeolites phillipsite, clinoptilolite, erionite, and chabazite have been surveyed for their gas adsorption, ion exchange, and other characteristics. Chabazite and erionite, which are generally more stable, also have higher methane adsorption capacities than do the other natural zeolites. Both natural erionite and natural chabazite are classified as small-port zeolites on the basis of their inability to adsorb chlorotrifluoromethane. In the range of 8 to 100 mesh, the adsorptive capac-ity of natural zeolites is improved only slightly by a decrease in particle size. The capacity of natural clinoptilolite to adsorb methane is increased by cation replacement by the hydrogen ion and decreased by exchange with calcium ion. Natural phillipsite, which is easily decomposed by heat, adsorbed methane to a limited extent.

Jan 1, 1973

For the past several years the policy of a large section of our mining industry in relation to our present bureaucratic form of government has become increasingly amusing, if not a little disgusting. In the past, mining men have always featured themselves the self-announced champions of free enterprise, and, generally, this conviction, was substantiated by their deeds. In recent years, however, a large group of the industry, while still expounding, from the front porch, the principles of free enterprise and a sound economy based upon the law of supply and demand, have gone around to the back door with palm extended, to join labor, farmers, bureaucrats, and other pressure groups to get their share of the take. The procurement of subsidies, bonuses, increased metal prices, and government assistance in a multitude of forms seems to have obscured from their thinking the welfare of the country as a whole and the sounder economic principles of a balanced budget and lower taxes. At the recent Colorado Mining Association convention in Denver, I. was alarmed to see just how far this specialinterest type of thinking has progressed within the mining industry. Government assistance to mining. was generally considered inadequate, and a flat bonus for any new mineral discovery was proposed. It was disquieting, too, to learn how far the federal alphabet agencies have entered into the mining industry and of the thousands of highly paid technical. men on the federal payroll required to man these numerous overlapping agencies and bureaus. Now all this is very fine, and some aspects of the federal give-away program can be very appealing to the unsuspecting in the mining industry as they have been to those in other groups. Some of these expensive programs may bring about a few dividends or even several new mines. But to this whole line of pump-priming reasoning there is one big disastrous fallacy.

Jan 1, 1952

By C. van Loggerenberg, P. E. Venter

The paper covers a wide range of modifications that are of potential interest to the practical coal-preparation engineer. Unfortunately, the paucity of performance data does not permit one to draw conclusions. The authors do not appear to have a clear understanding of the Tramp (or partition) curve concept.

Jan 1, 1992

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

Jan 1, 1983

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

By K. A. Johnson, H. F. Yancey

"INTRODUCTION Coals vary so widely in their burning characteristics that all coals prepared for domestic stoker use cannot be burned efficiently on every type of stoker. The overfeed stoker, a large number of which are in use in the Pacific Northwest, operates satisfactorily when burning low- to high-ash, noncaking bituminous or subbituminous coals, whereas on the clinkering-type, underfeed, bituminous stoker both caking and noncaking bituminous and subbituminous coals are burned, generally with ash contents below 12 percent and ash-softening temperatures between 1,800º and about 2,600º F. Because fly ash continues to be one of the most troublesome factors in domestic underfeed stokers, noncaking coals especially must be chosen carefully with respect to size composition, particularly as regards the exclusion of excessive fines. Their formation as a result of degradation in storage handling or because of crushing in .the stoker worm will increase the fly-ash nuisence.Bituminous and subbituminous coals with higher ash-softening temperatures and, often, higher ash contents have not been able to enter the domestic stoker-coal market in the Pacific northwest because clinkers are not formed readily during clinker-type underfeed-stoker burning, especially in mild weather, and because of the labor and attendant inconvenience required in handling larger volumes of ash. The work described in this report was undertaken to enable mines producing coals of the kind described to enter the stoker-coal markets. The anthracite stoker selected was one that conveys the refuse from the ash pit of the furnace and deposits it into one of two covered, dust-tight disposal cans."

Dec 1, 1945

By Orestis Zarzouras, Amalia Giannakou, Jacob Chacko

"When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.IntroductionThe Izmit Bay bridge, a 3-km-long suspension bridge that crosses Izmit Bay in Turkey, is planned to be constructed in one of the most seismically active places in the world. The south approach structures for the Izmit Bay Bridge along the western side of the Hersek peninsula bring the bridge down from on the order of El. 60 meters at the South Anchorage to an elevated embankment approximately 1.3 km farther south (Figure 1). The south approach structures are located within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The concept design team has developed a concept design for a “viaduct” structure that consists of 10 spans with lengths varying between 136 m and 100 m and two back spans one of 125 m, attached to the main bridge and the other of 74 m attached to the south embankment."

Jan 1, 2017

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By Jiajun Geand, Shuli Wang, Baodong Pan, Xueqi Cui, Guangwei Zhang, Jipeng Sun

Gravity-fed three-product dense medium cyclone(GTDMC)is usually used as the main coal washing equipment in coking coal preparation plant. It can produce three products with a low density suspension at the same time. Raw coal and dense medium are fed separately into the cyclone. Only the qualified low-density medium suspension is pumped into the cyclone while the raw coal is fed into the first-stage 1200mm cyclone axially at the top end by gravity. The 1200mm cyclone with a cylindrical form is for low-density separation. The clean coal with light density and slower-settling velocity moves directly towards the low pressure zone along the axis and is carried through the vortex-finder to the overflow. Only the heavy products pass through the "separating zones" to the wall of 1200mm cyclone and then migrate into the series-connected second-stage 850mm cyclone through the tangential outlet. The medium suspension from the first-stage cyclone is thickened and contains more magnetite coarse particles. The second-stage cyclone typically consists of a cylindrical section and conical part. These are all favorable for the second-stage cyclone to separate at a high density. Production practices show that the clean coal and the gangue rarely mixed in the middling, the lower limit of the separation is 0.2 mm, the Organic Efficiency and the Ecart probable of the first stage is 98.30% and 0.026 kg/L respectively.

Jan 1, 2014

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By I. Satola, J. Aromaa

In this work we have reviewed methods to classify corrosivity of ground waters. Weight loss and stress corrosion cracking (SCC) corrosion tests have been done for rebar and steel strand. No clear indication of SCC was found. The application of tensile stress to 85 % of yield strength increased general corrosion rate significantly in very corrosive waters. The effect of corrosion protection on the axial behavior of steel strands was determined by double pipe axial tests with different embedment lengths. The results showed a significant difference on behavior between epoxy-coated steel strands, galvanized steel strands and plain steel strand. Dans la présente étude, nous avons passé en revue des méthodes permettant de classifier la corrosivité des eaux souterraines. Des tests portant sur les pertes de poids et sur la corrosion FCC (la fissuration par corrosion sous contrainte) ont été effectués pour les barres d’armature et les torons. Aucune indication nette de FCC n’a été constatée. L’application d’une contrainte de traction allant jusqu’à 85 % de la limite d’élasticité a accru de manière significative la vitesse générale de corrosion dans les eaux très corrosives. L’effet de la protection contre la corrosion sur le comportement axial des torons en acier a été déterminé au moyen de tests axiaux à double tube avec des longueurs d’enrobage différentes. Les résultats ont mis en évidence une différence significative quant au comportement entre les torons en acier à revêtement époxy, les torons en acier galvanisés et les torons en acier standard. In dieser Arbeit haben wir Methoden geprüft, die korrosive Wirkung des Grundwassers einstufen. Gewichtsverlust- und SCC-Korrosionstests wurden für Stahlstäbe und Drahtlitzen durchgeführt. Es wurden keine sicheren Hinweise auf Spannungsrisskorrosionsbrüche gefunden. Bei Anwendung einer Dehnbelastung von 85 % der Streckspannung bzw.Ergebnisstärke stieg die allgemeine Korrosionsrate in stark korrosivem Wasser deutlich an. Die Wirkung des Korrosionschutzes bei axialem Verhalten von Stahldrahtlitzen wurde durch axiale Tests an Doppelleitungen unterschiedlicher Versenkungslänge determiniert. Die Ergebnisse zeigten im direkten Vergleich von epoxidbeschichteten, galvanisierten und normalen Stahldrahtlitzen beachtliche Unterschiede im Verhalten auf.

Jan 1, 2003

By Lawson F

The leaching behaviour of BHAS copper matte in oxygenated acidic sulphate chloride solutions at 85¦C has been studied using samples containing 34% copper, 41% lead and 12% sulphur. Copper sulphide in the matte, essentially Cu2S was found to leach in two distinct stages. Similar to the behaviour of pure chalcocite, copper dissolution in the first stage was affected by the availability of oxygen in solution. The presence of chloride ions in the leachant was essential if there was to be any leaching in the second stage (which usually commenced after about 40% of the copper had been taken into solution). Lead sulphide in the matte was oxidised to lead sulphate and formed a shell around the partially leached matte particles. Electrochemical studies showed that this lead sulphate and/or sulphur produced during leaching can form a passivating layer around the copper sulphide. However, this layer was disrupted when chloride ions were present. A Plackett-Burman analysis was used to determine the species in the recycled leach solution that affect the leaching of copper. Under the experimental conditions used, in the first stage the rate of copper dissolution was influenced by the concentrations of sulphuric acid, Zn(II), Cu(II), Fe(III) and Cd(II). In the second stage, the rate was futher modified by the concentrations of Cl(I) and As(V) ions. In solutions of low acidity and high As(V) concentration, insoluble copper arsenate formed which coated the partially leached matte particles and acted as a barrier to futher reaction.

Jan 1, 1989

By C. H. Herty

The results of a study of the open-hearth process from the physicochemical viewpoint are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. The effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styril from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900' F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,a Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 1, 1926

By D. G. Krige

Using chip sample data and spatial structure parameters from a large mined-out section of a South African gold mine the advantages to be gained from a regular underground borehole drilling programme have been investigated for short- and medium- to long-term planning based on block valuations. The results have been compared with the current position, which relies invariably on the extrapolation of limited peripheral sampling data from raises, gullies or stope faces. Some preliminary work has also been done regarding the implications of such underground drilling on costs used for the present pay limit calculations. The results of the study, though preliminary, show that the net advantage of advance regular underground drilling could be substantial and that a more intensive follow-up research is warranted.

Jan 1, 2003