Search Documents

By H. H. Kleizen

The operation range and efficiency of dewatering apparatus are important factors in the selection of an apparatus for a given purpose. In this paper theories are presented allowing to predict these basic characteristics for different dewatering apparatus and compared with experimental and practical data obtained on coal and ore slurries.

Jan 1, 1989

By Jason Palmer

"Water in mining is the commodity that has driven the mining industry for decades. Often used frivolously, modern economic and social pressures are forcing change to use less water and to improve the quality of water and effluents. Used in many processes, water is ultimately consumed in tailings disposal and technologies which can increase the recovery of water are constantly being developed. Filtration and thickening are often seen as competing technologies for water recovery however new cases are developing that show significant advantages can be achieved by combining the two technologies to develop the most effective solution. Supported by case studies this paper investigates the merits of each of the technologies and which strategies of combining the two produce the best outcomes.INTRODUCTIONMineral processing applications generally require water for the processing of ores, whether utilising physical or chemical methods. Water is first added in the milling stage and additional water added as required throughout the circuit. Water losses from the circuit are principally associated with the tailings stream. Optimised water recovery is necessary both because it is a scarce commodity and to minimise the environmental impact.Water recovery is usually accomplished through a sedimentation or filtration processes. Water can be removed from the tailings impoundment by evaporation but this does not improve the mine’s water consumption. The water recovery methodology also determines the water quality; increasing water recovery concentrates solutes in the process water and may create recirculating loads of fine solids."

Jan 1, 2016

By Mokka Rao, Asdrubal Serrano

"A mathematical model is developed which describes the movement of the minerals present where the vertical and angular velocities are related with the different operative parameters involved in the process of separation of silica from iron ore, which permit maximise the capacity of the spirals to obtain major productivity. The process is realised in two steps, of the rough dressing and other cleaning. Through the results obtained for chemical analysis of the final products of each spiral and the equation of movement of particles, it is proved the applicatibility and efficiency of mathematical model to operating parameters of the spiral. Moreover, it is determined though the recuperation of the final products of quality in the use spiral HC 1870 and HG 8/7. INTRODUCTIONThere is prospetive of increasing the production the iron ore in agreement with the demand of siderurgical proyects united with the external demand of quality 40 million tons per year. The Ferrominera de Orinoco Company is experimenting two types of modem spirals, Humprey (HC 1870) and Reichart (HG 8/7) which have limited capacity. For this reason this investigation designed a mathematical model with which larger units can be designed for increasing the capacity of the spiral."

Jan 1, 1999

By H. B. Charmbury

The acid mine drainage problem in Pennsylvania is of continuing and growing interest to the coal mining industry, the state government and the citizenry at large. Approximately one-third of the total volume of mine drainage presently polluting the streams of the Commonwealth originates from active coal operations and two-thirds come from ?abandoned mine discharges.? For this reason the Pennsylvania Department of Mines and Mineral Industries has mounted a significant research and action program seeking solutions to this two-fold problem. The Coal Research Board of the Department has sponsored a wide variety of research projects in an effort to study the treatment of acidic and highly ferruginous mine waters. A review of the published literature on the treatment of mine waters indicated that many laboratory and theoretical studies had been undertaken on various aspects of the coal mine drainage problem, but little applied, developmental, or engineering study had been undertaken. In January of 1964 the Board commenced a rigorous program using state and industry funds in an effort to find a ?least cost? solution or solutions to this vexing problem.

Jan 1, 1967

By Patrick Corser, Mitch Usibelli

Introduction Coal mining in Alaska's interior, specifically in the Healy area, began as early as 1918 with the construction of the Alaska Railroad. Mining was originally limited to underground operations but has expanded to entirely surface operations. In 1943, the Usibelli Coal Mine was formed and started developing Alaska's first surface mine east of Suntrana (Usibelli Coal Miner, 1984). Production from the local coal deposits has steadily increased and, in 1978, surface mining of Poker Flats was initiated (Fig. 1). Currently, a 25-m3 (33-cu yd) walking dragline strips two coal seams, using an extended bench on the second pass. In addition, a fleet of trucks and shovels are used for coal removal and some limited overburden stripping. In 1984, a contract was signed between Usibelli Coal Mine and Sun Eel Shipping Co. in 1984. Since then, production has nearly doubled to more than 1.3 Mt/a (1.5 million stpy). This article will discuss geotechnical constraints on mining within the steeply dipping coal deposits that exist within the Poker Flats mining area. Specifically, the article will describe how the mining operation retriggered an historic landslide on the No. 5 coal seam (Fig. 2). And the article tells how a mine plan was developed that allowed the coal to be safely removed without inducing additional movement. Regional geology The coal-bearing group in the Nenana coal field is of Tertiary Age. It is overlain in some areas by several thousand feet of Tertiary gravels - the Nenana Gravels. In areas mined by surface methods, the Nenana Gravels have been eroded off, and up to 30 m (100 ft) of quaternary outwash gravels overlay the coal-bearing formations. The coal-bearing group is divided into five formations: Healy Creek, Sanctuary, Suntrana, Lignite, and Grubstake (Wahrhaftig, 1969). Lignite Creek lies on the north limb of a west plunging anticline. This has brought the Suntrana coal-hearing formations near enough to the surface to allow surface mining. Mining is presently in progress on the south side of Lignite Creek in the Poker Flats area. The coal-bearing formation is cut off to the south by a fault having perhaps several thousand feet of vertical displacement, with the upthrust side to the north. South of this fault, Nenana Gravels are exposed on the surface. The Suntrana Formation contain the minable reserves at Poker Flats. This formation is a repeated sequence of poorly consolidated pebbly sandstone near the bottom, grading through a silty fine sandstone to a footwall clay unit immediately below a coal seam cap. The footwall clays are high plasticity clays to silty clays. It has been reported that they contain 30% to 50% montmorillonite (Usibelli Coal Mine Inc., 1982). There are six coal seams in the Suntrana Formation, No. I (the lower seam) through No. 6. Only the top four seams are currently exposed. No. 3, No. 4, and No. 6 seams are the only mined seams. The No. 5 seam is very thin or not present. Portions of the undisturbed Suntrana Formation are overlain by up to 15 m (50 ft) of Quaternary outwash gravels or recent landslide rubble. The surface is overlain by a very thin layer of muskeg and isolated areas of permafrost. In many areas, the outwash gravels are found immediately below the surface muskeg. Numerous landslides have been documented along the north facing slopes of Lignite Creek (US Geological Survey, 1970, and Wahrhaftig, 1958). These appear to be surficial solifluction or skin flow types of landslides. In addition, deep-seated structurally controlled slides are also evident on both the north and south sides of Lignite Creek. Structural features Premining aerial photographs (Fig. 3) of the Lignite Creek slopes in the Poker Flats area indicate substantial evidence of deep-seated landsliding. The landslides noted in Fig. 3 are both inside and outside of the current mining area. Surface mapping and geologic exploration indicate that the coal seams are dipping out of the slopes within the noted slide areas. It is suspected that, historically, these landslides were triggered by undercutting of the toe of the slopes by Lignite Creek. And sliding it thought to have taken place on one or more of the clay beds underlying the coal seams (Golder, 1985). The slide areas are characterized by semicircular head scarps and slumped topography. Based on the premining photographs, these slides do not appear to have been recently active. However, they are expected to be in a state of only marginal stability. Extensive coal exploration indicates that the primary structural feature within the

Jan 1, 1989

By O. Tiitu

Drying is a unit process that has numerous applications in metallurgical process industry. Kumera Technology Center is a worldwide equipment and process supplier, who has expertise on both direct and indirect drying. In a conventional direct heated dryer, the required energy is obtained from combustion of fossil fuels emitting a considerable amount of off-gases. However, thermal energy can be already available in some metallurgical plants such as modem copper smelters where steam is produced by waste heat boilers of flash smelting furnaces. The total volume of off-gases, and especially the amount of harmful gases, released into atmosphere can be remarkably reduced when using steam as an indirect energy source for drying. Kumera Technology Center has developed a new type of steam dryer for drying of, for example, abrasive copper concentrate with silica sand. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the existing steam dryers and the rotating drum dryers. In the design, special attention has been paid to overcoming the reported problems of excessive wear and clogging of steam tubes and to reducing the required maintenance operations. The Kumera Steam Dryer, having a patented flexible steam tube arrangement inside the rotating shell, has a high effective heating area - drum volume ratio without leading to problems with build-up and clogging. It can also be easily scaled up so that a single dryer can dry all of the feed for a large flash furnace. In this paper, we will present the operational and maintenance experiences from two years operation of the first full-scale Kumera Steam Dryer at Norddeutsche Affinerie Aktiengesellschaft in Hamburg, Germany. We will also provide an overview of the future developments with respect to construction and scale up as a response to market demands.

Jan 1, 2002

The mine planning and operational aspects of applying Continuous Surface Miner (CSM) technology to Australian coal strip and open cut mines is investigated for both existing and planned deposits. CSM produc- tivity as a function of geomechanical properties, formation thickness, mechanical availability and in-pit physical constraints, are considered. Productivity and operational costs are derived from current production machines and from first principles.

Jan 1, 1989

By Legett Garrett

Texas Utilities Generating Company (TUGCo) surface mines lignite for use as a boiler fuel at mine mouth generation stations. Currently, the annual lignite production requirement of approximately 28 million tons necessitates mining across approximately 1,600 surface acres each year. The mining operations, located in Freestone, Panola, Titus, and Hopkins counties, Texas, have drastically disturbed some 13,000 surface acres to depths of up to 110 feet since initial startup in 1971. The TUGCo mining philosophy, a commitment made prior to initiation of mining operations and prior to any mining regulations, includes a return of mined-out land to private ownership in the most useful state possible. In the areas of TUGCo operations, the local economies are based upon agricultural production. Historic land use surveys have typically shown a trend from row crop production to pastureland for cattle production. During the 1960?s, the percentage of acreage devoted to row crop production approached zero with respect to the total acreage devoted to agriculture. TUGCo reclamation operations have therefore emphasized restoration of land to a state that is favorable to cattle production

Jan 1, 1982

By Radmuller H

The proposed underground mine at Porgera forms an integral part of the Porgera Joint Venture project in Enga Province in the remote Highlands of Papua New Guinea. The total in-situ reserves are approaching 400 tonnes of gold making the Porgera deposit one of the largest in the world. The remote, rugged and inhospitable terrain, recent unstable geological environment and primitive yet socially complex nature of the densely populated local community, combine to make the Porgera project very different to developing mines in Australia. The Porgera project is a challenging and exciting mining exploration venture in the final stages of feasibility study submission and negotiations with the National Government of Papua New Guinea. A 1476 m exploration adit was driven in the footwall of the high grade mineralisation for diamond drilling purposes as part of the evaluations necessary for the feasibility study. Ground conditions encountered have ranged from weak mudstones with high water content, requiring immediate steel set support, to competent intrusives.

Jan 1, 1988

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By Tony Weeks, J. Loah, Ian Mcgaffin

PT Newmont Minahasa Raya (PT NMR) operates a 700,000 tonne per annum open cut gold mine in the Minahasa region of North Sulawesi. The operation commenced production in the second quaiter of 1996 and is expected to produce an average of 150 000 to 180 000 ounces of gold per year for the mine life. The deposit is predominately refractory in nature and requires a complex treatment route incorporating dry milling and whole ore roasting followed by conventional cyanidation and adsorp­tion of the gold onto activated carbon. Gold is eluted from the carbon to produce <lore bars assaying approximately 94 percent gold. A scrubbing system for the removal of mercury from the roaster off gases was commissioned in late 1997. Due to the location of the operation, close to the coast and in seismic region with high rainfall submarine tailings placement (STP) was the preferred method of tailings disposal. Prior to dis­posal into the ocean the tailings from the CIP plant are detoxified in a three stage detoxification circuit to treat cyanide, arsenic and mercury. This paper reviews some of the design and operational fea­tures of the whole ore treatment process employed at the Minahasa Gold Mine.

Jan 1, 1998

Simple parameters, capable of easy observation on-site under operating conditions without interruption to production, are outlined for the operational assessment of underground conveyor systems. Recording techniques, methods of analysis and deduction of operational characteristics are discussed for batch inputs to several points of a multiple belt conveyor system with limited inter-belt storage capacity. Particular attention is given to input and output load- time distributions, utilisation of inter-belt storage capability and system shutdown behaviour. Actual data, observed for a transfer feeder located between two trunk conveyor belts in an underground coal mine, is used to illustrate the operational assessment of an underground system. Load sensitive feedback systems-are briefly considered.

Jan 1, 1982

By Rob van Opbergen, Edo Engel

The highly dynamic economic climate of recent years has tightened the operating envelope for steel producers world-wide. Steel producers continue to experience immense pressure to respond quickly to changing circumstances and the focus has shifted towards efficiency improvement and maximizing flexibility in operations. The ability to safely stop, restart and ramp-up production facilities has become essential. Establishing this level of flexibility, without sacrificing efficiency, requires sound process control, fit-for-purpose process management practices and solid know-how and experience regarding special situations in blast furnace ironmaking operations. The same business environment that demands this increased flexibility has made it increasingly difficult for steel producers to sustain sufficient knowledge about these situations. While many experienced, senior operational staff have retired, a new generation of ironmaking specialists has acquired its hands-on experience over more recent decades, during which these process situations have been much less frequent than before. Over the past 10-15 years, the requirement in the industry for external operational support during e.g. blast furnace blow–downs, salamander tapping and restarts after planned and especially unplanned stops, has become increasingly frequent. This article presents a number of these cases from a process management perspective as well as with regard to project organization and optimized cooperation between internal and external teams of experts.

Oct 1, 2019

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By S. Kirkpatrick, J. Mukendwa

"The mining operation at Namdeb’s Southern Coastal Mine (SCM) is unique. It targets gravel layers up to 30 m below sea level, which continue to dip deeper, further west, under the Atlantic Ocean. On this storm-dominated coastline, severe water seepage into mining areas, rugged orebody footwall characteristics, and highly variable resource grades all contribute to a challenging operational environment. Namdeb has a proud history of innovation, and as the mine progresses further westwards and associated technical and economic challenges increase, this innovative culture has become essential to the future of the mine. The Theory of Constraints (ToC) has been widely used at SCM, and across the mining discipline, to focus efforts on improving overall business profitability. Through analysis of the mining processes, opportunities were identified, solutions developed, and initiatives implemented with staggering results across all three mining disciplines, i.e. stripping, load and haul, and bedrock bulking and cleaning. This paper outlines the solutions adopted and the results of the ToC analysis. IntroductionSouthern Coastal Mine (SCM) is one of three Namdeb operations located in the southwestern corner of Namibia, between the Orange River in the south, the Namib Desert to the east and the Atlantic Ocean to the west (Figure 1). These three geographical features set the backdrop for the world’s greatest marine diamond mining placer (Badenhorst, 2003). SCM is situated along the coastline extending from the mouth of the Orange River to Chameis Bay approximately 120 km to the north. The active mining area, called Mining Area 1 (MA1) is, however, limited to very narrow strip, 30 km in length, in the south of the licence area, close to the town of Oranjemund.Namdeb, a wholly owned subsidiary of Namdeb Holdings, is a 50/50 joint venture between De Beers and the Government of Namibia. Diamonds were first discovered along the Namibian coastline in April 1908, close to the town of Luderitz, but mining operations started in the SCM mining area only in February 1929 (Schneider, 2009). Initially all Namdeb mining operations exploited massive land-based deposits, producing nearly 40 million carats from MA1 between 1920 and 1977 (Schneider, 2009) when mining targeted onshore raised beaches west of the high water line. Since 1977 however, SCM and Namdeb have developed a unique mining method to economically extract the resource which extends westward under the Atlantic Ocean."

Feb 1, 2019

By Ian Farmer, Nigel Glossop, Philip Garritty

Performance of tunnel boring machines - usually expressed in terms of penetration per revolution - is determined by relations between machine thrust and torque, head diameter and rock strength. It can be shown that for a given machine power and head diameter there is only one rock strength at which the machine performs optimally. In weaker rocks the available torque limits performance and in stronger rocks, the available thrust. Performance data shows that, historically, machines have been designed to cut weaker rocks. Optimization of thrust is required to improve performance in stronger rocks.

Jan 1, 1987

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011