Search Documents

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017

By Daniel Bennett

There are few methods currently applied towards on-line bulk mineralogical analysis. Yet on-line knowledge of process mineralogy could potentially provide large benefits, such as increased extraction efficiency or resource optimization. The work described in this paper involves the development of radio frequency methods for bulk mineralogical analysis. Some resonances that occur in the radio frequency spectrum are mineral specific, and potentially allow quantitative estimation of mineralogy in an ore stream. Results will be presented on the specific detection of chalcopyrite. Initial quantitative measurements investigating matrix effects have indicated the feasibility of on-line mineralogical estimation using radio frequency techniques.

Jan 1, 2006

By Daniel Hodouin, Claude Bazin, Sami Makni

Computer systems, installed in mineral processing, are designed to accumulate massive amounts of real-time data. Frequently these data are only partially processed because of the lack of adequate methods and the limited accuracy of mineral processing sensors. Methods are proposed to estimate missing data and reconciliate sensor data on a real-time basis. They are based on dynamic extension of steady-state techniques such as the node imbalance minimization or the least-squares mass balance adjustment techniques. The methods are illustrated for simulated and actual flotation data. Their data upgrading ability could be used to improve process monitoring, control and optimization.

Jan 1, 1993

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By S. K. Kawatra, K. A. O, DeLa&apos

On-line sensors and process controls are important for efficient operation of coal preparation plants. The objective of this paper is to describe the current practice in on-line measurement of composition, density, moisture, level, flow and weight. This paper also discusses how on-line sensors can be implemented in process control, and how sensors which are currently being developed can be utilized.

Jan 1, 1988

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By Paul M. Musgrove, Larry S. Diaz

Recent tests conducted at Inspiration Consolidated Copper Co. examined some aspects of the value of a continuous measurement of particle size to the operation and control of a mill grinding circuit. Inspiration's control objectives and kinds of control systems developed in recent years to attain these objectives are outlined. A description is given of the arrangement of the test circuit at Inspiration and also of the systems used to measure particle size of the cyclone overflow product in these tests. Use of on-line size measurement for the analysis and improvement of grinding circuit performance is illustrated by relating how two important relationships were detected. Finally, the performance of a particle-size-based control system is described, including preliminary conclusions as to increased productivity.

Jan 1, 1974

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By J. R. Sturgul, J. C. Wynn

Computers and computer applications in geophysics are fairly recent innovations. The area of data handling is one that has found many immediate applications. Initially, the use of computers involved in almost all cases, a batch-input arrangement requiring a trip to the local computer center, a wait and another trip. Even though the computer worked at incredible speeds, the time-delays, in case an error in the input data developed, often could be several days. Use of computers in mining exploration by medium-sized or small-sized companies and contractors has been almost non-existent beyond simple data reduction work. The principle J. R. Sturgul, SME member, and J. C. Wynn, both affiliated with the Dept. of Geosciences, University of Arizona, Tucson, presented this paper at the Eleventh International Symposium on Computer Applications in the Minerals Industry, reasons appear to be the time factor and the inconvenience of the frequent trips involved. With the advent of time sharing systems, whereby a company need only have access to a terminal, the main objections can be overcome. An Apparent Solution An apparent solution to the time and distance inconveniences which would permit more extensive use of computers in geophysical exploration, is to buy or lease/purchase a medium-sized computer and install it in or near one's office. This is a formidable proposition in terms of cost and programming time on both respects, but several mining companies of larger size have already gone this route. In most cases, the computers have been expensive devices with a limited memory or core size. For routine data handling this memory size is not restrictive; however, for many geophysical applications such as three-dimensional modeling this can be critical.

Jan 10, 1973

By G. T. Adel, J. D. Miller, C. L. Lin

In view of the success of recent laboratory studies using X-ray computed tomography (CT) to determine coal washability and with the availability of high-speed CT systems, it now seems possible to design an on-stream washability system for the control of coarse coal-cleaning circuits. Design features for such a system are examined and possible control strategies are discussed for different applications.

Jan 1, 1995

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

By H. N. Frock

The use of low-angle forward light scattering for measurement of particle size distribution has been described previously.1 Laboratory instrumentation using this technology is used routinely in operating plants for quality control and production control.2,3 Extension of the technique to on-line process monitoring and control has also been undertaken in several important areas. This paper will discuss the application of MICROTRAC R systems to the monitoring of particle size in wet slurry processes and dry powder grinding circuits. Examples of existing installations will be given with emphasis on performance and on-line reliability.

Jan 1, 1979

By Fuzail Siddiqui

"The SIDMIN program aims at filling the mineral processor’s need to know the deportment of ‘minerals of interest’ not just ‘elements of interest’ that pass through the processing plants. Generally, chemistry is used as a tool of routine monitoring on site. Mineralogy, which is relatively much slower, is used more as a tool of research and post mortem investigations and these services are usually provided by a distant facility. The SIDMIN program enables site management to receive chemical and quantitative mineralogical reports on their critical samples daily, simultaneously and affordably.The author developed the SIDMIN program at ZCCM Nchanga Division where it continues to be a powerful tool for monitoring the efficiency of operations. Outlines are given of procedures for quick sample preparation and quantification of significant minerals in process samples. A specimen report is presented, which shows the format of reporting the contributions of individual minerals to metal losses at critical stages of the circuit. It is shown that SIDMIN provides timely information to management, about trends and abrupt changes in the quality of ore, and its processing, in a way never achievable by chemical analyses alone. This greatly helps in resolving the age-old problem of ‘bad ore’ or ‘bad operations’ on a day-by-day basis. For example increase in copper mica in the feed indicates excessive ore dilution during mining. Increased loss of free sulphides was traced to insufficient reagent conditioning time at the Concentrator. Persistent losses of leachable oxides at the Tailings Leach Plant were traced to inadequate leach residence time.SIDMIN is affordable because it can be implemented using basic optical microscopes, minimal quantities of micro-chemical reagents and custom trained site staff who demonstrate good colour perception and an ability to follow laid down procedures consistently."

Jan 1, 2000

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By Akira Usui

The small-scale observations, mapping, sampling, and in-situ experiments have been carried out since 2009 using JAMSTEC ROVs at some model seamounts in the Northwestern Pacific seamounts. Laboratory analysis on mineralogy, chemistry, chronology indicated a continuous slow precipitation since the Middle Miocene, at water-depths 1-6 km, and the modern hydrogenetic precipitation even in the oxygen minimum zones. Thus the variability in abundance and grade of the deposits on regional, small and microscopic scales are determined by geological, geochemical, and hydrological conditions, resulting in the stacked piles of tiny precipitates from the seawaters.

Jan 1, 2018

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990