Search Documents

By Paul L. Goddard, Alfred G. Hoyl, William R. Sirola

A good place to look for elephants is in elephant country, and old mining districts are certainly elephant country as far as minerals are concerned. In many areas probably more ore is still in the ground than has been taken out. The old timers were good miners and hard workers and when they left ore behind, it was usually for good reason; but many an old mining district has been revived by new approaches to old problems, taking advantage of new techniques and new equipment. One of these is the Front Range mineral belt of Colorado, which has produced minerals for the past 100 years through the ups and downs of mineral prices and the general economy. Gold, silver, copper, lead, and zinc have been found in abundance in the complex sulfide veins of the area. Between Idaho Springs and Central City lie several strong veins which have been mined successfully in the past. The two strongest of these veins, striking northeast-southwest, (Lake-Bald Eagle), and northwest-southeast, (Crown Point-Belman) , and dipping northeast and northwest, respectively, intersect in a flat X near the head of Virginia Canyon. From the lowest drainage of the area, Clear Creek Canyon, the old timers drove the Central, or Big Five, haulage-drainage tunnel due north. It intersects the two veins 8460 ft from the portal and 1670 ft below the surface. The two veins were mined successfully at the surface and at the tunnel level. Without an opening to the surface at the in- side end of the tunnel, ventilating became very difficult as the stopes were opened up, and mining ceased in 1929. Vertically, 1200 to 1600 ft of virgin ground remains in the veins.

Jan 6, 1959

By Robert J. Timko

New methods of reducing stopping leakage have been investigated by Mine Safety Appliance Research Corporation, working under contract to the U. S. Bureau of Mines. It was found that proper construction techniques are far more important in reducing leakage than the type of sealant used, provided the sealant has sufficient adhesion and strength. Leakage could also be substantially reduced by brushing on modified mortar sealants rather than using the accepted method of trowelling them on.

Jan 1, 1982

By James E. Lawver

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent or at least delay mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the forms of calcined bones at least 2 000 years ago, (1) and man has used phosphate minerals as a source of fertilizers in one form or another for at least 100 years. During 1977 the world produced about 116 million metric tons of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows. Marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits, requiring an apatite carbonate mineral separation.

Jan 1, 1978

By George F. McKeregahan

Phosphate production of the Central Florida Phosphate District has been predominantly from the unique and lucrative Bone Valley Formation, with local and minor amounts coming from the underlying Hawthorn Formation. As the Bone Valley is depleted, replacement production will move progressively into areas of total Hawthorn Production. Significant changes in the characteristics and make-up of the deposit dictate required modifications in mining and beneficiation. Failure to tailor technology to fit the deposits of the future will result in vast "reserve" losses. In the Southern Extension of the Central District - two distinct "ore types" exist. These are presently referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation and will respond favorably to present beneficiacion practices. The lower zone is strikingly different and its response to conventional beneficiation is not acceptable. The major differences are in grain size distribution and mineralogical make-up of these grains. The Hawthorn differs from the Bone Valley by exhibiting lower grades, lower tonnage yield per acre foot, lower pebble percent of product, higher mining ratios, higher slimes (-150 mesh) content and deeper mining depths. Physical characteristic changes include more frequent occurrences of competent bands or lenses of "limerock" which are submarginal in value.

Jan 1, 1983

By James E. Lawver

Part I describes the general geology of the Florida deposits. As the lucrative Bone Valley Formation is depleted, replacement production will move progressively into areas of total Hawthorn production. The reserves of the immediate future are a mixture of two distinct ore types referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation that has been Florida's source of production for the past 100 years and will respond favorably to present beneficiation practices. By contrast, the lower zone ore contains significant quantities of dolomite that must be removed in order to produce an acceptable grade pebble or flotation sized product. Part II reviews past practice and describes future trends in mining and ore transportation. This presentation (Part III) is confined to the problems of beneficiation, waste disposal, and environmental regulation.

Jan 1, 1983

By J. E. Lawver, J. D. Raulerson, Charles C. Cook

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent, or at least delay, mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the form of calcined bones at least 2000 years ago (Anon., 1964), and man has used phosphate minerals as a source of fertilization in one form or another for at least 100 years. During 1977 the world produced about 116 Mt of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows: marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits requiring apatite carbonate mineral separation. [ ] Guano, mostly from Chile and Peru, accounts for 0.1% of the total world production, and the calcium phosphates from Ocean, Nauru, and Christmas Islands and the aluminum and iron phosphates from Brazil and Aruba account for less than 4% of the world production and are thus not considered in this classification (Lawver, et al.). At present, marine phosphorite deposits account for about 75% of the world's production; the igneous deposits account for 20%. The igneous deposits low in carbonate minerals are easily concentrated by crushing, grinding, and apatite flotation. The most important igneous deposits are those of the Kola Peninsula, USSR (Woodrooffe, 1972). The igneous deposits high in carbonate materials are of corn appreciably more difficult to beneficiate, but they have been concentrated by froth flotation for a number of years. An interesting but rather complicated flowsheet of this type is at Phalabonva, in the Republic of South Africa (Lovell, 1976). The Phalaborwa deposit is an igneous complex of pyroxenite with a central core of carbonatite surrounded by a serpentine- magnetite-apatite rock called phoscorite. The phoscorite containing about 10% P2O5, 35% magnetite, and 35% calcium magnesium carbonate is currently being processed. The process involves comminuting the material for fiberation and subjecting it to a copper float using a potassium amyl xanthate as collector and triethoxybutane as a frother followed by a magnetic separation of the tailings to produce a feed for phosphate flotation. This process produces a phosphate concentrate containing greater than 36% P2O5 at a P2O5 recovery ranging from 75 to 80%. Considerable success has been claimed for recovering apatite from carbonate-bearing ores at the Jacupiranga Mine of Serrana S/A (Silva and Andery, 1972). The carbonatite currently being mined contains an average of only 5% P205 and is concentrated using a unique flotation process (Andery, 1968) to yield 96% P205 concentrates. The ore contains about 12% apatite, 5% magnetite, 80% calcite plus dolomite, and minor amounts of phlogopite, olivine, zircon, ilmenite, and pyrochlore. Feed preparation consists of crushing to -31.75 mm (-1 M in.), rod milling in closed circuit with hydrocyclones to about 92% (-50 mesh), and two-stage cyclone desliming of the -50 mesh sands at 20 m. Weight recovery in the deslimed feed is normally 85 to 88% and the corresponding P2O5 recovery is usually about 90%. The deslimed feed is conditioned at 60 to 70% solids for 15 min at pH = 8-10 with 0.6 kg/t of causticized starch for iron oxide and calcite-dolomite depression. The conditioned slurry is diluted to 20 to 30% solids, about 0.2 kg/t of fatty acid or soap collector is added to the conditioner discharge, and the reagentized ore is subjected to rougher-scavenger flotation with additional fatty acid added to the scavenger float. The scavenger concentrate is returned to rougher circuit distributor, and the rougher concentrate froth is subjected to two stages of cleaner flotation to yield a final apatite concentrate analyzing 36 to 38% P205. Flotation recovery of P205 is, in general, above 90% when treating fresh carbonatite. The high-carbonate flotation tails normally analyze 1 % P2O5 or less and are suitable for portland cement production. The marine deposits. Types 1 and 2 of central Florida are representative of enormous reserves of phosphate rock that will undoubtedly account for much of the world's production in the near future. Until very recently the sedimentary deposits high in carbonate minerals (Type 2) have not been considered reserves due to the difficulty in making a francolite-carbonate separation. Although no commercial plant has yet been built to beneficiate Type 2 ore, laboratory and pilot plant data indicate the process is viable. If so, the reserves of Florida and similar deposits throughout the world will be substantially increased. A discussion of the beneficiation of these two types of sedimentary deposits and the relation of the resulting concentrates to the fertilizer industry of the United States is the subject of this paper.

Jan 1, 1981

By J. E. Lawver, J. D. Raulerson, J. P. Bernardi, R. S. Hearon, D. Lynch, G. F. McKereghan

Despite recent economic problems, the future of the Florida phosphate industry appears optimistic. Florida has enormous reserves and will continue to produce a third of the world's phosphate supply simply by making changes in the present system of mining, beneficiation, waste disposal, and land reclamation. The geology and mineralogy of future deposits are discussed with reference to specific deposits. Lower ore grades, increasing power costs, and environmental regulations are necessitating development of new concepts of mining and matrix transportation. Because one of the ores to be mined in the future contains appreciable amounts of dolomite, research and development efforts are being concentrated on new techniques in beneficiation. Changes are being made in plant design to meet environmental and regulation standards. However, the expected new technology outlined for the industry depends on the geology and mineralogy of future reserves.

Jan 1, 1985

By James E. Lawver

At the present time, the Florida phosphate industry is experiencing one of the worst marked slumps in its one hundred year history. Recent agriculture over-production has caused low grain prices such that the net income of U.S. farmers is expected to drop to its lowest level since the 1932 depression. The farmers' low income, along with high interest rates that preclude them from borrowing to purchase fertilizer, make the immediate U.S. phosphate market outlook bleek at best. The export outlook is also pessimistic due to world recession and the U.S. dollar's high exchange rate. In June, 26% of the phosphate industry's workers were laid off for an indefinite period of time. Despite the immediate painful slump, the long-term outlook for the industry looks good. Florida has enormous reserves and will continue to produce a third of the world's phosphate supply simply by making changes in the present system of mining, beneficiation, waste disposal and land reclamation.

Jan 1, 1983

By Norman J. Tienkaivip, Christopher J. Preston

"This paper describes the use of electronics for physical measurement and computer analysis in both open-pit and underground mining operations for the ultimate purpose of optimizing production blasts. Techniques in monitoring single borehole blasts using both pressure and vibration sensors to establish in-situ dynamic rock properties are outlined, including characterization of multiple borehole production blasts with regard to stress generation.Once field derived measurements are computer analyzed, they are channelled as input parallel to other data, such as the explosives thermochemical performance properties generated by a sophisticated computer program called ""HT-65"" into BLASPA . BLASPA, a blast simulation computer program, then couples these input with a mathematical model which defines the blasting processes. Aspects such as the blast geometry, explosive loads and distribution, hook-up, and costs are studied. The final output table gives specific blast performance or quality factors for each blast procedure. These results are then easily compared and rapidly optimized to achieve maximum performance at lowest blasting and drilling cost."

Jan 1, 1984

By Cyril Heever

ROCKS outcropping in Elandsrand's lease area consist of quartzite, shale and lava of the Pretoria group and are underlain first by 1 300 metres of dolomite and then by the Black Reef series. This in turn rests unconformably on Ventersdorp and Witwatersrand rocks and truncates the basal member of the Ventersdorp Super group, the Ventersdorp Contact Reef (VCR), near the northern boundary of the lease. The Ventersdorp Super group is composed of lava and varies in thickness from nil in the north of the lease area to 1 000 metres in the south. The VCR, less than 100 cm thick, dips 210 to the south east and lies between 1 786 and 3 386 metres below datum. The Oberholzer dyke straddles the north-western corner of the property and separates the dewatered Oberholzer compartment, over which most of Elandsrand lies, from the as yet undewatered Turffontein compartment. As so much of the lease area is covered by thick impermeable rocks, the water-bearing capacity of the underlying dolomite was expected to be low. The man-material (MM) and rock hoisting ventilation (RU) shafts were sited well within and above a gravimetrically determined 200-metre 'safe-limit' contour of the northern slope of the Gatsrand. Two pre-cementstion holes were drilled and the cementation rigs were placed within a 15 metre annulus round each shaft to seal any likely water-bearing pockets in the proximity of the excavation during sinking through the first 300 metres of shales and the surface water-table.

Jan 1, 1981

By Hans Lundberq

IINDUSTRY'S attention is now focused on the production of munitions thereby creating a demand for certain minerals which in prewar days were produced only in limited quantities. Now production of these minerals must he increased from the known deposits and new deposits must be found. Can geophysics help? "War minerals" such as tin, vanadium, tungsten, antimony, manganese, chromium, and cinnabar have no physical characteristics sufficiently different front the country rook to permit their direct location by ordinary geophysical methods. As already demonstrated in work on gold and oil, useful information may be obtained indirectly, however, outlining structural features or geological conditions favorable for the deposition of such ores or the accumulation of oil. Recently, more direct and truly qualitative methods have been brought into a useful and practical stage, and by the combined application of old and new methods a technique has been developed which, it is hoped, will be of importance in the search for these vital minerals.

Jan 1, 1941

By Kendrick C. Hardcastle

The practice of transporting an ore or matrix from a pit area to the plant process area by means of a hydraulic pipeline has long been used by the mining industry. The industries which have classically used hydraulic transportation of ore to the plant include the phosphate mining industry, the heavy minerals mining industry, the clay mining industry, and the sand mining industry. As the advantages of this method become better known throughout the mining industry as a whole, and as techniques and expertise improve, its use will undoubtedly spread. Its use is presently being contemplated in iron mining diatomaceous earth mining, and several industries where massive removal of overburden is a predicate to economical mining. The widely recognized advantages of hydraulic transport at ion of ore from the pit area to the mines are: 1) Its relatively low initial capital costs. 2) Its speed of relocation at the mine site. 3) The washing and scrubbing action given to the ore by its hydraulic passage into the pit pump and the subsequent trip through booster pumps down the pipeline to the plant.

Jan 1, 1969

With more difficult economic conditions and increased competition, the Australian exploration industry is allocating increased resources to developing more effective and efficient exploration technologies. A significant number of new techniques have been developed, and Australian companies are now at the forefront of exploration technology worldwide. These should increase the chances of maintaining Australia's leading position in world mining over the long term.

Jan 1, 1987

By R. J. Watters

Many rock sass classification systems exist' to assist the engineer in assessing the rock support requirements for underground design. Our ongoing research in this area is directed at attempting to utilize the fractal dimension and the acoustic emission' response of the tuffs at Yucca Mountain, Nevada to further aid in rock mass classification. The Topopah Spring' member, the proposed nuclear waste horizon, is characterized by welded and partly welded tuffs, exhibiting a wide range in moduli, strength, porosity and degree of fracturing. Differentiating between the different' types of porosity can be extremely difficult if not impossible. An attempt was made to correlate the acoustic emission response with the porosity of the sample. Events and the peak amplitude may offer a means-to distinguish between, fracture porosity and pore porosity. In addition-, fractal dimension were calculated for several fractures in densely welded tuffs. Two techniques for calculating fractal dimension were-applied' to describe-fracture geometry and roughness. Fractures in-welded-tuff were-found to be relatively smooth.

Jan 1, 1989

By G. Pahomova

"It developed an alternative to traditional flotation enrichment refractory of complex lead-zinc ores to obtain conditional lead and zinc products. The scheme involves the use of the processing method of gravitational enrichment of the primary cycle and the combined gravity-flotation-hydrometallurgical in finishing. The method has a high level of comprehensive utilization of mineral raw materials in relation to the elements that are extracted in the process of enrichment in lead concentrate, and the increase in recoverable value of processed ores. INTRODUCTION The primary source of lead are complex sulphide lead-zinc ore, lead ore actually rarer. The value of lead and zinc ores (except lead and zinc) is determined by the presence in them of a wide range of associated components: silver, contained mainly in galena; gold; bismuth in the form of its own minerals, but is associated with galena; cadmium contained mainly in the sphalerite; indium, thallium and gallium contained in sphalerite and galena; selenium and tellurium are present as impurities in the sulfide, tellurium is also found in the form of its own minerals. Of note harmful impurities antimony, which is often associated with lead sulphosalts and arsenic, having a substantially own minerals. By quality (content of lead, or the total content of lead and zinc) lead-zinc ores are divided into rich, ordinary and poor; by oxidation - to sulfide (with a lead oxides content less than 15% and zinc oxide content less than 10%), mixed and oxidized (50% oxide); the latter have a subordinate importance as a source of zinc and lead. Traditionally, the most contrasting technological properties of sulfide ores of nonferrous metals considered flotation properties, which determines the priority in the selection of flotation technology of their enrichment. Other methods of enrichment - gravity (jigging and enrichment in heavy suspensions), radiometric sorting (separation) are used as preliminary operations whose main purpose is to increase the content of lead and zinc in the ore sent to flotation, as well as the removing of part of empty rock in dumping tails prior to flotation. Effective implementation of these methods is possible at large size emphasizing in the ore of lead and zinc minerals, which is typical of the rich ores and which so far mainly worked. At the same time, non-ferrous metal ores (polymetallic, lead-zinc, copper-zinc, etc.) have a sufficiently high contrast to gravitational properties since ore minerals have a higher density compared with a rock minerals. But the gravity of the practice of non-ferrous ores enrichment is not widely used, despite its high degree of environmental safety and lower cost expensive."

Jan 1, 2018

By Andreas Rompel

New technologies and applications in exploration and mining are the result of R&D. As the acronym indicated, R&D is separated into Research and Development. They represent different stages in the progress of the development of a new application.

May 1, 2008

By Brotzmann K, Turner RE, Philp DK, Rusden RC

New approaches in the last decade have led to the supplemental use of raw coal as a direct energy source in several iron and steelmaking processes. The dependence on more expensive coke and electricity is being progressively reduced. The Technology Venture of Klockner Werke and CRA has pionered several of these developments and is pushing ahead to processes for scrap melting and direct smel- ting of iron where coal is the ONLY energy source. Such complex developments depend strong- ly on the experience gained in the simpler but related processes for coal use already in operation. The longer term implications of a successful coal-based direct smelting process for the world steel industry are substantial.

Jan 1, 1986

By Johnson T, Huynh D

The State Electricity Commission of Victoria is conducting a program of research and development into alternatives to the use of conventional boilers for the generation of electricity from brown coal. The objectives of the program are to reduce the cost of electricity generation and also to improve the thermal efficiency so as to reduce the emission of greenhouse gases and other pollutants. The program presently includes the following four technologies: Hydro-thermal Drying, Direct Coal Fired Gas Turbine, Integrated Gasification Combined Cycle, and Steam Fluidised Bed Drying. The Hydro-thermal Drying process produces a combustible coal-water-slurry fuel which is suitable for use in a coal fired gas turbine. The coal fired gas turbine has the potential to produce electricity at a lower cost than conventional power stations and when combined with a steam cycle, it will also use significantly less coal. The Integrated Gasification Combined Cycle process gasifies the coal, cleans the gas, and then bums it in a gas turbine/combined cycle. This process is being developed in Europe and the USA in order to meet their stringent emission regulations. It offers Victoria cleaner more efficient and cheaper electricity.

Jan 1, 1992

By J. Lee, M. Peart, T. Bhambhani, D. R. Nagaraj, P. Riccio

"Over the past decade or so, our efforts have focused on developing the rationale and concepts for new technology in reagent development and optimization in the processing of base and precious metals. A major outcome of these efforts have been the development of a novel family of collectors, principally driven by the MAXGOLD® and Aero XD-5002® chemistries, for precious metals recovery from primary Au ores and Cu-Au ores. These chemistries was developed to be robust to address the complex mineralogy and gold deportment in these ores. Plant trial data for a variety of ores have confirmed that the both Aero® XD-5002 and MAXGOLD® chemistry are indeed versatile in recovering gold values occurring as gold alloys and/or associated with many types of sulfides, and in altering the deportment of certain sulfides (such as those bearing As, Bi etc). An overview will be given in this paper using plant data to highlight the application of these reagents.INTRODUCTIONThe subject matter of this paper is the flotation of Au containing minerals from their ores. The motivation from this manuscript comes from the several challenges faced with the processing of Au ores, as was articulated in detail by Nagaraj (2008). The biggest challenge is the complex mineralogy; most easy-to-treat free-milling ores bodies are largely depleted. The Au values are distributed in multiple host minerals such as pyrite, pyrrhotite, arsenopyrite and Cu minerals such as chalcopyrite. Au values also happen to be finely disseminated within the various minerals and are sometimes invisible in optical microscopy. Additionally, on any given day, some mines treat multiple ore types, and the mineralogy is different for each ore type.Xanthates continue to be the collectors of choice at most Au and PGM operations around the world. Most primary Au operations tend to consume very large amounts of collectors; the dosage ranges anywhere between 40-400 g/t and this has been attributed to both mineralogical and non-mineralogical factors (non-mineralogical factors include the low cost of xanthates and the mindset that “more is always better”, which is not necessarily the case). In addition, several studies now show that xanthates alone are never sufficient where multiple value minerals are present, and that supplementary collectors are required. The large doses present a substantial cost to the minerals industry, and many mining companies have expressed the need for more efficient reagents that can improve metallurgical performance at low dosages."

Jan 1, 2013

The Mt Keith Mining Alliance operates a fleet of large capacity hydraulic face shovels and more than 40 X 240 t capacity haul trucks to deliver annual production in excess of 40 Mbcm per annum. The Mt Keith Nickel mine is currently operating at a depth to 300 m below surface with a planned final depth of the order of 500 m. As is the case with any large open pit managing the health of the workforce on continuous shift operations is of critical importance to achieving outstanding safety and production outcomes. Fatigue management at Mt Keith is effectively managed by the personnel operating the mining equipment, with assistance and understanding of the management team and supervisors. The program has been driven through the introduction of Fatigue Champions and a comprehensive management plan that includes education, individual health plans and the use of new technologies. Mt Keith has been instrumental in trialling new technology which assists in monitoring fatigue in operations personnel. Insight into these developments is provided in the context of the overall fatigue management plan. The field trials of the OptAlert(TM) system and how it assists in measuring fatigue is explained. The implications for individual operators and the context for a fleet wide approach to fatigue management is also discussed. Mt Keith has recently completed the second phase of trials with the result that this new and exciting technology is being considered for adoption globally across BHP BillitonÆs open pit mining operations.

Jan 1, 2007