Search Documents

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

As modern techniques of Petroleum Exploration and Development are rela-tively new in Australia,2 the alien terms "Mud Logging" and "Core Analysis" will bear explanation. Mud Logging and Core Analysis are two of the Petroleum. Industryts most useful "tools" in the successful search for, and development of, commercial oil and gas deposits. Modern Mud Logging could be more accu-xately termed "Drill Cuttings and Mud Gas Analysis". Presently, mud-logging has its greatest application in exploratory wells where subsurface geologic control is at a-minimum.

Jan 1, 1962

By R. Butcher

Mud rushes are hazardous occurrences that have occurred frequently in mines in South Africa, and have been the cause of numerous fatalities in the past. Mud rush incidents not associated with accidents are believed to be common occurrences that are not generally reported. Many such incidents are probably associated with the operation of chutes and box fronts. This paper describes the conditions necessary for mud rush occurrences, postulated mud rush mechanisms, and methods of combating the mud rush hazard.

Jan 1, 2005

By M. W. Strong

THE technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in forma-tion, the type of problems met with, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differen-tial pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all mate-rials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improve-ment of material and its most efficient use has to be carried out. In this paper we propose to discuss the main mud problems with which we have to deal in Iran, some of which are peculiar to our local conditions while others are of the general type common to all workers in this subject.

Jan 1, 1938

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By Lincoln Silva Gomes

Processos metalúrgicos durante soldagem provocam tensões residuais em peças soldadas. Recentemente foi observado um efeito de redistribuição das tensões residuais de soldagem num período de até duas semanas após o termino do processo de soldagem. Existe hipótese nossa que esta redistribuição das tensões está associada a mudança na microestrutura que ocorre no material após do processo de soldagem. Para provar esta hipótese, uma simulação física dos ciclos térmicos do processo de soldagem foi realizada utilizando a simulação física termo-mecânica (GLEEBLE). Através da técnica de microscopia eletrônica de varredura associada a técnica de difração de elétrons retroespalhados (MEV–EBSD) foi observada a variação da misorientação dos grãos e mudanças na microestrutura do material nos primeiros dias após soldagem, acompanhada de redistribuição das tensões residuais.

Aug 17, 2017

By John V. Beall

Many Americans will judge the energy crisis by the picture shrink on their TV screen. And they are right to make this assessment considering the large areas of the country with marginal generating capacity, (See Fig, 1). The Federal Power Commission (FPC) recommends 20-25% reserve generating capacity above peak summer loads and 15-20% as minimal. The New York metropolitan area is the most concentrated power service area in the United States, and a spot check with Consolidated Edison, serving this area, revealed that on Friday, August 18, the company was operating at 5% reserve.

Jan 10, 1972

Water is important commodity in the mining industry. Water is used in the many stages of mining from the exploration stages and drilling, to mine development and operation and finally throughout mine rehabilitation and post mine activities. With the use of water throughout the life span of a mine, its management is an important component in the operation of any mine. Unfortunately the use of water within the operations can be one of the major sources of pollution generated from a mine. Such contamination can occur via numerous mechanisms including ground water flow, over land flow and accidents. Contamination may occur in any stage of mining operations, for example a leaking or failed tailings dam. With the above in mind, the paper presented will focus upon the use and management of water in the mining industry: ownership rights of water û common law as well as legislative rights; a review and analysis of the existing Queensland legislation and its mechanisms for the protection of water pollution from mining operations; and conclusions drawn from the paper relating to the Queensland legislation.

Jan 1, 2003

By L. C. Clare

In a meeting of this kind where everyone present is connected with or engaged in coal mining, and where each one is present with the set purpose of learning new thoughts or ideas, the subject of the saving of life by any method in the industry is a vitally interesting and important one. On the cost per ton basis, it mounts to a formidable figure especially so during these days of depression and stagnant, or no business. But entirely outside of the human side of the question, to lose lives would cost more than saving them. Your insurance under haphazard safety measures would mount, loss of time due to accidents would impair efficiency among employees and the breaking of the morale of the staff, due to criticism of lax methods would cost more than an efficient safety program. Taking it for granted that most of you are looking at the question from the viewpoint of a yearly or five-year cost sheet, and that at this time you are doing all that can be done without bringing a ruinous cost upon your companies, I can offer only one suggestion: Raise the quality of your safety, or lower the cost. In this meeting, there should be no question of standing still or retreating in the quality of safety, so I will amend the suggestion with "Raise the quality and lower the cost." We have learned that when the coal beds were forming, nature sealed them in with a strata of mud that the ages have turned to shale, sealing them effectively against the deteriorating influences of the air. Mudite is carrying out nature's plan of coal preservation to the inside of the coal mine. Text books teach us that a large proportion of the vegetation that forms our present coal beds grow on what might be termed mud, later falling and being buried practically where it grew by mud, then on being subjected to heat, pressure and time, was changed to coal. The mud being subjected to the same three forces forms our present shale stratas. Now if nature saw fit to use this solidified mud as a preservative through countless centuries, isn't it reasonable to expect that occasional coatings on the ribs and roofs of entries and rooms will aid materially in preserving our coal and coal dust? Nature took mud and formed it into shale; mudite takes the shale, reduces it into dust, adds water and makes a mud, applies it to the ribs, roofs and floors of the mine in a thin coating

Jan 1, 1925

PRESIDENT LITTLEJOHN: We have with us a gentleman from Utah, who is familiarly known -as the "Mudite King," Mr. Reid, of the Lion Coal Company. Here is a letter I would like to read, and probably Mr. Reid will give us an idea of his Mudite machine, or the results he is obtaining. This question was brought up in Rock Springs, Wyoming, but Mr. Reid was not there personally during the discussion, but Mr. Burnell, who is general superintendent of the Lion Coal Com¬pany, as much as he possibly could, described the system and its effects. I believe Mr. Reid will probably be able to give a somewhat clearer statement this afternoon. This letter is from the Coal Mining Inspector of the State of Utah, John Crawford. "February 10, 1925. "The Industrial Commission of Utah, Building. "Statement of John Crawford, Coal Mine Inspector, in regard to Muditing in Coal Mines: "That Muditing used in connection with our present sprinkling system in coal mines is the missing link to the system we have had heretofore, because the water applied by the former system began to dry out, in heavy air currents, the moment it was put on. Consequently the dust that had been humidified by sprinkling, came back to its natural condition, and if anything, the combustible parts of it, in my opinion, were more intensified than previous to being wetted down. "The advantages that Muditing has over the old system of sprinkling are: "1st. The dust that is on the roof, timbers and sides of the entry is washed completely off and rolled up in the Mudite solution which entirely destroys the wings, crudely speaking, of the fine coal dust. "2nd. Sprinkling with the Mudite system, the water and mud is of greater extent than could be applied with a hand hose by a sprinkler. This sprinkling can be done while the mine is in operation, just the same as if water alone was being used. "3rd. The Mudite solution, when dried out, leaves a coating which serves as an armour to the coal, so that in the event of a local explosion, the inflammable matter on the coal is non-combustible; whereas, if that same coal had been sprinkled with water only, and made free of dust, the heat would have the same effect on the coal as it has on a stove when coal is thrown into it-instantaneous combustion. "Therefore, it is my opinion that the Mudite system is the missing link to the perfecting of our sprinkling system here in Utah. "(Signed) JOHN CRAWFORD." Mr. Reid has with him a few sam¬ples of his Mudite, after it has become solidified, taken from the floor, as I understand it. It is interesting. We have a few minutes to spare to good advantage, were we to ask Mr. Reid to give us an idea of his machine, as briefly as he possibly can, and also what he thinks the effect of the Mudite is compared to dry rock dust. Mr. Reid. (Applause.) MR. W. J. REID (Lion Coal Company) : I came down here with no intention of making any talk on Mudite. However, there being so many people that have seen Mudite at Wattis

Jan 1, 1925

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By A. J. Sinclair

Los métodos de desmuestre para estudios de viabilidad dependen de las características geológicas del yacimiento que ha de ser evaluado. Se requiere un estudio geoestadístico preliminar, teniendo en cuenta los aspectos de autocorrelación de las variables sometidas a estudio, con objeto de que el plan de diseño de muestras pueda ser optimizado para producir las estimaciones de ley y tonelaje dentro de los límites de errores establecidos. En general, debe de tenderse a una distribución regular de muestras para ello, y longitudes regulares de las mis¬mas (a partir de los testigos o cortes, por ejemplo) son preferidas con objeto de facilitar los análisis estadísticos. Los planes de desmuestre son modificados y mejorados (bien técnica o económicamente) a medida que avanza el programa y es obtenida información adicional. Las muestras a granel para pruebas metalúrgicas pueden ser evaluadas en término de va¬riaciones señaladas por todas estas muestras en un depósito y la variabilidad de la ley dentro de las mismas. Una atención adecuada sobre estas fuentes de variabilidad asegurará una evaluación adecuada de los resultados de las pruebas piloto de las muestras a granel. Por otro la¬do, un estudio mineralógico general del yacimiento es un requerimiento importante, a veces ignorado, en una evaluación más general pero semicuantitativa de la representatividad de una muestra a granel; y, además, proporciona una información muy útil para optimizar el diseño de la planta.

Jan 1, 1982

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By S. W. Arambur

INTRODUCTION "Mujeres Roca" is a program developed by OMA in association with the Chamber of Commerce Canada Peru inspired in “Women who Rock”, a Canadian initiative to promote a greater participation of women in the mining industry. The program includes a coaching workshop called “Kallpa Warmi”, that means “Woman Strength”, to reinforce basic skills and values and 8 mentoring sessions with top executives of the mining industry who share their experiences and knowledge with a group of 10 selected young professional women from around the country. HISTORY OMA is a nonprofit association founded in 2014 dedicated to contributing to the education of low-income university students with high academic performance in careers related to mining and earth sciences. Our mission is to empower the future professionals by strengthening their soft skills and enhancing their capacity to become leaders and agents of change in their own regions. The Chamber of Commerce Canada Peru has a long-standing commitment to gender equality and promotes women participation in male dominated industries. As it is well known, the mining sector is and has always been key to Peru’s economy, representing about 10% of the country’s GDP. Thus, mining can contribute significantly to our economic development and we believe that women can make a positive difference. A study prepared by PwC and "Women in Mining” provided indicators on the advantages that mining companies have when including women in their executive’s positions. These indicators sustain that when a mining company includes women in its management staff, its net profit increases by 6%. This information clearly shows that women participation is not only a matter of human rights and gender equality, but of productivity and profitability. Nevertheless, the mining sector has the fewer number of women on boards of any industry group in the world. Having this in mind, OMA decided to expand its activities and create together with the Chamber of Commerce Canada Peru, the program “Mujeres Roca”, in order to inspire and attract young women to the mining sector, a traditionally masculine industry. The program also aims to encourage mining companies to more actively recruit and keep women in their boards. The program was launched in 2016 within the framework of EXPOMINA PERU, the largest international mining exhibition that take place in Lima every two years.

Jan 1, 2019

A significant resource of uranium has been discovered within a buried palaeochannel located in the south western corner of the Officer Basin of Western Australia by PNC Exploration (Australia) Pty. Ltd. The mineral- isation is redox controlled and is hosted by Eocene organic rich paludal sediments. Prob- able insitu reserves are 13,000 t of contained uranium with an average ore grade of 0.12% at a cutoff grade of 0.03% U. The Mulga Rock palaeochannel has been traced for at least 100 km beneath the Quaternary surficial cover. The main channel is horseshoe shaped with the channel arms vary- ing from 5 to 15 km in width. The western arm connects to the Lake Raeside-Ponton Creek drainage system, whilst the eastern arm'is open to the south. The headwaters of the palaeo- channel are thought to have been the Lake Minigwal drainage system, prior to its capture by the Lake Rason system. Differential.erosion of the basement rocks during the Late Cretac- eous to Early Tertiary strongly influenced channel shape and resulted in the main channel being confined to a Permian,mudstone filled valley. Upwards of 100 m of fluviatile sediments accumulated within the palaeovalley during a period of subsidence in the Early Tertiary. Three broad stratigraphic units have been re- cognised within the channel: 1. An upper unit of fluviatile sands with interbedded lacustrine sediments, which have subsequently been wholly oxidised and variably silicified and ferruginised. 2. A middle unit of lacustrine to paludal sediments, which host the main mineral- isation. 3. A basal unit of fluviatile gravels and sand. The presence of excellently preserved Nothofagidites in organic rich paludal sediments from the middle unit, suggest that unit was laid down in a non-marine, fluviatile, humid environ- ment during the Middle Eocene.

Jan 1, 1988

By J. M. Karpinski, F. P. White, R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball, the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corp.'s Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about 50% without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1972

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By Bowen Li, Jiann-Yang Hwang, Mingsheng He, Huaguang Wang

Kyanite is one of the major high-alumina minerals for producing refractory ceramics. At high temperature, kyanite can be decomposed into mullite and amorphous silica. This change is an irreversible decomposition and provides potentials for fiber reinforcement of ceramic matrix. In this study, kyanite powder was compressed into a cylinder green body of ceramic and heated at 1150–1450 °C.The phase transformation of kyanite and sinterability were investigated by X-ray diffraction and scanning electron microscopy. The results showed that the phase transformation of kyanite started at 1150 °C when rising the temperature. At 1350 °C, kyanite is completely converted into mullite and silica. The compressive strength of the ceramics reached 73.3–134.8 MPa, while the bulk density was 1.95–2.47 g/cm3. The microstructure indicated the correspondence of the compressive strength to mullitization degree of kyanite.

Mar 1, 2017