Search Documents

By Jack C. Jones, Hemendra N. Kalia

This paper is partially based on a comprehensive ground control investigation that was conducted by Harza Engineering Company under a contract from the Bureau of Mines. This investigation required in- stalling several types of ground movement indicating devices on the surface and in the mine. The major instrumentation systems consisted of hydraulic borehole pressure cells, multi-point extensometers, in- clinometers, convergence indicators, Jack pressure recorders time domain reflectometers, and a 200 station subsidence network. The investigation demonstrated the versatility of the system. We were able to install pressure cell s to a depth of over 200 feet in the coal bed and we were successful in installing 10 pen mechanical recorders to monitor differential strata movement. In this paper, we have briefly discussed data from 18 borehole pres- sure cells, two time domain reflectometer cables and four subsidence lines. The data collected showed that the front and rear abutment pressures were approximate1 y 1000 feet (304.81~1) to 1200 feet (356.76111) from the active face. The peak pressure was about 4 times the over- burden pressure.

Jan 1, 1983

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By Thomson S, Eisenstein Z

Field instrumentation was installed to monitor ground and lining behaviour during and after construction of the Mount Shaughnessy Tunnel (Rogers Pass Short Tunnel) in Canada. The instrumentation was placed in a soft ground section of the tunnel at its crossing with the Trans Canada Highway. The tunnel was excavated through a dense bouldery soil. Presentation of the field data and inter- pretation of the tunnel performance from a geological-geotechnical point of view form the basis of this paper. The loss of ground due to the tunnel excavation was found to be exceptionally small. This has been attributed to the unusually high strength and stiffness of the host soil. Evaluation using the Boundary Element Method, together with a simplified analytical technique, were applied to assess the relevant soil parameters and their influence on the tunnel performance.

Jan 1, 1987

By C Aldrich

In this paper, the use of topology preserving projections (Sammon maps) and neural networks are considered as a basis for the construction of multivariate statistical process control charts for a semi-autogenous grinding circuit on a gold plant. Comminution circuits are often operated in a quasi-steady state mode, where the mills tend to move rapidly from one state to another. This makes them difficult to monitor by conventional means designed for continuous steady state processes. As a first step, process data reflecting normal operating conditions are mapped with SammonÆs algorithm. Only one feature is extracted at a time and each mapping is captured by a neural network model to allow online application. Reverse neural network models are used to reconstruct the data prior to the extraction of subsequent features from the data residuals. The ensemble of neural network models can then be used for both fault detection and identification. The approach compared favourable with both linear and non-linear principal component models. It was able to detect two simulated fault conditions both with a reliability of 100 per cent, as opposed to 57.8 per cent and 95.2 per cent detected by an approach based on the use of linear principal component analysis and 84.1 per cent and 98.0 per cent detected by an approach based on non-linear principal components extracted with auto-associative neural networks.

Jan 1, 2007

By R. Ghisleni, R. E. G. Bohrer, L. Radtke, R. M. C. Santana

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionThe first major global assessment of climate change science in six years has concluded that changes in the atmosphere, the oceans and glaciers and ice caps show unequivocally that the world is warming. The report released on February 2, 2007, the first of four volumes to be released this year by the IPCC, also confirms that the marked increase in atmospheric concentrations of greenhouse gases is the result of human activities.The transport sector has become by far major source of environmental pollution in urban areas. The continual traffic growth has raised concerns over the impact of traffic emissions on human health and urban environmental quality, and has fuelled the demand for a coherent regulatory framework for the management of traffic, air quality and emission at urban level, as well as at regional and national scales.In Greater Metropolitan São Paulo, Brazil, fossil fuel combustion in the transportation system is a major cause of outdoor air pollution (Miraglia&El Kouri, 2007). In China several studies on gaseous emissions are being conducted by F. Costabile&Alegrini, (2007), developed a study on the pollutants in the city of Beijing suggesting methods for the control of pollution.The results obtained from the estimation of the atmospheric pollutants emitted monthly in Campo Grande/MS, Brazil, by buses and minibuses, which employ diesel, biodiesel or natural gas as fuels showed that the substitution of diesel by biodiesel would diminish the emissions of pollutants (Kozerski&Hess, 2006)."

Jan 1, 2008

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

By Richard E. Thill

Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind-backfilling process has been particularly successful for stabilizing ground over abandoned and inaccessible underground coal mines. Using this newer technology, vast quantities of backfill material can be distributed over wide areas in underground openings from a small number of injection boreholes. The rapid and successful development of this backfilling method, however, has outstripped technology for monitoring and controlling backfill placement. Surface or borehole remote sensing methods are needed to determine where fill material is being distributed underground and how effectively the material is packed in the voids. In search for improvements in backfill monitoring and control technology, potential remote geophysical sensing, process monitoring, and tracer methods were evaluated to select candidate systems for monitoring backfill placement under the constraints imposed by the injection process and the surface and subsurface conditions. ' A multiple objective ranking matrix, based on theoretical considerations as well as pragmatic experience with systems working in related or similar conditions, was used to narrow down potential methods to several most-favored candidates. Two of the candidates were field tested under actual operating conditions at a backfilling site in the Wilkes-Barre-Scranton region of northeastern Pennsylvania. Although process and acoustic emission monitoring indicated promise for improving existing backfill monitoring technology, more extensive testing under different conditions at various sites is required to establish the validity and utility of these methods. Results indicate that no single method is adequate in itself for backfill monitoring, and that a successful system will require the Integration of several methodologies.

Jan 1, 1982

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By F. Charette

Instrumentation has been developed that can monitor the strain applied to a D-Bolt up to 7.5% elongation. The technology far exceeds the limit for foil resistance strain gauges. In the laboratory the instrumentation has provided insight into the fundamental behaviour of the D-Bolt following yield. Currently the instrumentation is undergoing field trials at a number of Canadian Mines. Discussion on field results is provided with regards to significance, reliability and temperature effects.

Aug 1, 2013

By P. Mousset-Jones, F. Calizaya

Currently, a 4.3 km long drift is being developed on the 3440 level in the Lower Kalamazoo project at the San Manuel Mine, Magma Copper Company, AZ. The drift, located at 1050 m below surface, is being constructed using a 4.6 m diameter tunnel boring machine (TBM). The drift is ventilated by a forcing type auxiliary ventilation system. At the face, to mitigate the impact on the work environment of the TBM, the system is equipped with dust extraction and refrigeration systems. Recently, to evaluate the ventilation conditions in the drift, a continuous monitoring system has been installed. The system can be used to measure the air velocity, barometric pressure, relative humidity and air and rock temperatures. This study describes the capabilities and limitations of this system, and presents a summary of the results.

Jan 1, 1995

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979

By B. G. Bunting, D. L. Abata, J. Robb, J. H. Johnson

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during mining operations. The explosives included two semi-gelatin dynamites, three slurry explosives, and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and toxic gases produced by the detonation were trapped at the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/1bm): NO, 0.0100-0.035; N02, 0.003-0.019; CO, 0.08-0.30; SO2, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1983

By Robert C. Freas

Dravo Lime Company has opened a new 290m (940 ft.) deep lime-stone mine near Maysville, Kentucky. As the mine was opened there were many unknowns as to the stress relationships within the rock, and their influence, if any, on the selected mining method. Therefore, a system of overlay geologic and structural maps, borehold extenso-meter measurements, and oriented photography was developed for the purposes of monitoring the internal structural relationships of the rock mass. This paper presents a description of the methods used, the observations made, and the conclusions and recommendations made as a result of the initial monitoring program.

Jan 1, 1977

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By Ken Mills

Dartbrook Mine (Australia) works the Wynn seam, which has a moderate propensity for spontaneous combustion. Prior to any mining a commitment was made to place a segregation barrier pillar between longwall blocks 4 and 5. This was to segregate goaves and improve management controls in the event of a spontaneous combustion event within previous longwall goaves. An alternative to the segregation barrier known as a Consolidated Barrier was developed; firstly as a concept, then computer modelled and finally field tested. It consists of a wider than normal chain pillar with concrete Mega-Seals placed in cut-throughs. Permeability and stress measurements were conducted in the surrounding coal of the seal. Remote monitoring took place as the longwall face approached and then passed by the seal. Results indicate that as the longwall retreats past the seal, horizontal stress increases. The additional stress leads to an increase in confinement and a subsequent reduction in permeability.

Jan 1, 1999

By A McEwan, J Masters, C A. Jackson, A Catanzano, V Sharp, M Millen, S Rainey, S J. Spencer, G Roberts

A passive acoustic emission (AE) monitoring system has been developed and trialled on two M10000 IsaMillsTM. The analyser detects AE stress waves generated by grinding media impacts with the mill liner during mill operation. Locally propagating stress waves can be detected on the exterior liner surface using strategically mounted broadband accelerometers.The analyser has been developed into a robust commercial prototype system, and has been designed, installed and commissioned with Xstrata Technology at two mineral processing plants.A six-month field trial showed large-scale variation in AE power signature with process conditions. Analysis of the enveloped AE power output demonstrated a strong correlation with mill process conditions – more specifically grinding media relative loading, feed pulp density, feed volumetric flow rate and feed type.Placement of accelerometers along the length of the mill body provided key information on the grinding media relative deportment. The enveloped AE power detected by the mill body, discharge pipe and bearing housing sensors all captured information strongly correlated with mill operating parameters and process state.The prototype analyser demonstrates suitability as a long-term online tool for stirred mill performance monitoring, and potentially for optimisation and control, in beneficiation plants.CITATION:Jackson, C A, Spencer, S J, Masters, J, Sharp, V, McEwan, A, Rainey, S, Catanzano, A, Roberts, G and Millen, M, 2014. Monitoring of M10000 IsaMill™ process performance by passive acoustic emissions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014