Search Documents

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By R. Minnitt, C. Morgan, D. Fourie

The problems associated with outliers and their adverse effects on resource estimation in deep level South African gold mines are presented, and solutions suggested in available literature are reviewed. Traditional Witwatersrand type outlier capping uses the 99th percentile grade as the upper limit, a somewhat blunt approach. The occurrence of high and low grade areas in mining operations and the estimation of resources using geostatistical techniques require that the assumption of stationarity be upheld. Honouring the stationarity of data requires that mining areas be subdivided into appropriately sized and spaced domains. In order to overcome high-grade conditionally biased block estimates, the overly strong influence of extreme grades is mitigated by using naturally occurring grade sub-domains, by identifying outliers within the grade sub-domains, allocating relevant capping limits, and weighting them in a post-estimation process to. Rather than applying a capping value across a domain it applies a maximum cap based on the extreme value and its range of influence; the method also ensures that relevant capping occurs even in lower grade sub-domains. The proposed method for capping outliers recognises that metal contained in high grade chip samples should not be over-capped, and based on the grade of surrounding samples. The post-processing method of capping outliers does not interfere with the kriging equations. The method is simple, elegant, and can be easily applied. An advantage is that the output from the kriging process is not overwritten, allowing for comparison between original kriging results and post-processing results.

Sep 1, 2021

By Michelle Pienaar, Musa S. D. Manzi, Thabang Kgarume, Glen T. Nwaila, Raymond J. Durrheim, Abrie Oberholster, Hennie Grobler

The South African Mining, Extraction, Research, Development and Innovation (SAMERDI) strategy was launched in 2019 with the goal of modernizing the mining industry. It comprises three major research initiatives: improvement in the efficiency of extraction and health and safety in current mining operations, development of fully mechanized systems to mine narrow tabular ore bodies in hard rock, and development of extraction systems to break rock without using explosives. The crosscutting Advanced Orebody Knowledge (AOK) program seeks to develop and implement drilling and geophysical technologies that can characterize the rock mass ahead of mining and identify potentially hazardous geological features. This knowledge will be integrated with information derived from seismic monitoring. Mining methods, layouts and rock support systems will be adjusted accordingly to mitigate the risk of rockbursts. Boreholes are routinely drilled ahead of mine workings using diamond-impregnated bits. The drill core is logged to identify lithology and geological structures (especially dykes and faults that may be seismogenic), sample the ore body for grade control, and detect areas that may contain water and/or flammable gas. Methods and technology to improve the efficiency of drilling and maximize the information obtained from the drilling process, borehole core, and the borehole itself are being investigated. A range of geophysical technologies are being developed to map the rock mass from the skin of the excavation to a distance of several tens of meters. Light Detection and Ranging (LiDAR) is used to map the geometry of the excavation, including prominent joint, vein and fracture sets and the presence and performance of rock support elements and systems. Ground Penetrating Radar (GPR) is used to penetrate deeper into the rock mass and image joints, fractures bedding planes that influence the stability of the hanging and side walls. Image processing techniques known as ‘seismic attributes’ are being applied to the radargrams to improve interpretation. Electrical Resistivity Tomography (ERT) and various active and passive seismic techniques (e.g. Tunnel Seismic Profiling (TSP), ambient noise tomography) achieve even greater penetration into the rock mass. Finally, machine learning is used to improve the processing and interpretation of seismic and radar data.

Apr 26, 2022

By Jurgens PE Hamman, Faisal Putra, Hadnaltias Alpeki, Willem de Beer

The Deep Ore Zone mine is the third lift of caving at PT Freeport Indonesia’s East Ertsberg Skarn System. An increasing trend in seismicity along the northern boundary of the DOZ cave, as well as the northern fringes of the DOZ production and infrastructure levels, was taken as indicative of an interaction between the approaching DMLZ cave and the DOZ subsidence zone. Seismicity trends and locations indicated a reducing crown pillar and an associated stress increase along these DOZ excavations, as well as the regional area along the DOZ cave boundaries. Although rockbursts were not identified as an immediate hazard, seismic shakedown was a highly probable hazard in the case of remote large (≥3.0) seismic events. An evaluation process, as described in the Canadian Rockburst Support Handbook (1996), was followed to identify and quantify the various parameters that could contribute to a shakedown evaluation. A shakedown assessment, based on the Peak Particle Velocities scaling relation, was conducted to assess the current installed ground support systems along the northern fringes and the fixed facilities of the DOZ mine. The range in ground support systems were mostly due to different geotechnical environments. The load–deformation characteristics of these support systems were evaluated to determine the support capacity and compared to the potential support demand under varying shakedown conditions. Shakedown hazard maps were compiled to indicate the installed ground support system’s vulnerability to seismic shaking. Based on this information, areas were divided into zones indicating whether they were sufficiently supported, additional support was required, access was to be restricted, and / or they were to be abandoned. Mine management utilised these hazard maps to strategize actions for the various operational zones within the DOZ, including the fixed facilities. This paper briefly describes the derivation of the PPV scaling relationship. Seismic and geological data for the DMLZ – DOZ interaction areas were evaluated to determine the likely source of large events. Subsequent larger events and their effects are shown to assess the veracity of the magnitude and PPV estimates, as well as the effectiveness and appropriateness of the ground support systems.

Apr 26, 2022

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By Daniel W. H. Su

A nearly 305-m- (1,000-ft-) wide sandstone channel was projected to run through the mid panel area of a 457-m- (1,500-ft-) wide longwall panel in a southwestern Pennsylvania coal mine. This sandstone channel was known to cause serious longwallface roof control problems in the mine?s B-panel area in 1998 and 1999; and most recently, it induced many large face cavities and caused a substantial production delay in the preceding panel. For the two B panels mined in 1998 and 1999, hydraulic fracturing of the massive sandstone was conducted to facilitate better caving, thus relieving cantilever compressive stress at the longwall face. Vastly improved longwall face condition was observed and four weeks of mining delay due to bad roof conditions were eliminated. The implementation of the hydraulic fracturing technique, results of underground observation and measurement, and results of numerical modeling were summarized in a paper presented in the 20th International Conference on Ground Control (Su et al., 2001). This article is a summary of the activities that took place during a four-month period (October 2011 through February 2012) at a Consol Energy longwall mine southwestern Pennsylvania to improve face conditions and safety of underground personnel during mining of the 457-m- (1,500-ft-) wide longwall panel. The elevated concern for safety was driven by adverse face conditions encountered while mining the preceding longwall panel. Many of the problems were attributed to a thick and massive sandstone channel. A joint task force consisting of coal operations engineering, Pennsylvania operations engineering and CNX Gas personnel was formed in August 2011, which recommended drilling four hydraulic fracturing holes along the center axis of the sandstone channel to reduce pressure and improve face conditions at the longwall face. To further provide detailed monitoring of the longwall face and to evaluate the effectiveness of the hydraulic fracturing program, the Longwall Visual Analysis (LVA) software (Hoyer, 2011) was installed in early December 2011 to track the face pressure and c

Jun 1, 2013

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By Nate Ober, Heath Rushing

"Mining companies want to be in a position to move quickly and seize a favorable market or to keep their key staff productively busy. One of the problems for these companies is the time required to compensate for unavoidable impacts that the mine will have on the natural environment and to gain environmental permits. All too often, circumstances that were favorable when the project was proposed have become less favorable by the time all the hurdles have been cleared.Accordingly, many mining companies are interested in ways they can inject more predictability into their timelines for gaining environmental permits, shorten those timelines, and be more certain of getting the permits they need to carry out their next project.One increasingly popular way to do this is through a relatively new kind of service — the mitigation bank.Mitigation banks purchase property or easements through property that has been impacted by agricultural, industrial or resource activity. They then turn it around from an environmental point of view. This might include restoring streams and wetlands so that fish and aquatic organisms can survive, and animals have habitat and food to flourish.Appropriate native species of plants including trees and shrubs are planted, and steps may be taken to introduce wildlife to the new habitat. In some cases, a special focus is placed on creating habitat for rare and endangered species of plants or animals.The property is inspected by regulatory authorities, coordinated through an interagency review team (IRT). If the property is determined to be effective as natural habitat, the mitigation bank is then issued credits that it can then sell to development projects that are creating an unavoidable permitted environmental impact elsewhere. A mining company, for example, would buy credits to offset the aquatic impacts due to construction of a mine, access roads and other infrastructure — as required by the Section 404 Clean Water Act permit that governs those unavoidable aquatic impacts. The mitigation bank used for offset must have an IRT-approved service area that includes the location of the impacts."

Jan 11, 2017

By William Gleason

"Mining roots run deep in Glenrock, WY, a town that was founded in part, because of the coal mining that began in the late 1800s. But that rich history also now threatens large parts of the town that were built over the top of the mines. Like many towns in the Western United States, mining is a proud part of the historical fabric and heritage of the town, but the legacy issues from past mining activities continue to present challenges to modern-day engineers.In the case of Glenrock, a small town about 40 km (25 miles) east of Casper, it is flooding from a century of water that has accumulated in the down geologic dip of the furthest northeastern extent of 87 ha (217 acres) of mine workings that has made the town susceptible to sinkholes and other issues (Fig. 1).Full commercial coal mining production began in Glenrock in 1887 during the development of the Fremont, Elkhorn and Missouri Valley railway. Due to poor overlying roof rock and continuous flooding within Glenrock, Mines No. 1 and 2 were fully closed in 1909. During its history, an estimated 87 ha (217 acres) were mined with 50 to 60 percent extraction ratio within the eastern town limits through room-and-pillar mining. It is estimated that the mines produced 22 kt/a (25,000 stpy) during their lifetime. A century later, the water pressure built up in the northeastern most portion of the mine has created serious concerns for residents.In 2016, the Wyoming Department of Environmental Quality’s Abandoned Mine Lands Divisions (AML) investigated a number of subsidence events in the town including sinkholes following heavy precipitation. The AML investigations confirmed that most events were related to the previous mining in the area.Mitigation efforts on the mines were done in the 1980s and 1990s, but the problems in the town and in a nearby subdivision persisted, leading the AML to search for alternative solutions."

Nov 1, 2019

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By Daniel W. Su

This paper presents the implementation and evaluation of the hydraulic fracturing technique and Longwall Visual Analysis (LVA) software to mitigate the impact of a 1,000-ft (305-meter) widemassive sandstone channel on a 1,500-ft-wide (457-m-wide) longwall face. Based on a underground roof geology reconnaissance program, four frac holes were drilled and fraced along the center axis of the sandstone channel. To further provide detailed monitoring of the longwall face, the Longwall Visual Analysis (LVA) software was installed to track the face pressure and cavity formation index. In mid-December 2011, the longwall face approached and entered into the western edge of the sandstone channel. The longwall face mined through the center axis of the sandstone channel in mid-January 2012 and advanced outby the eastern edge of the sandstone channel in early February 2012. Results from daily underground observations and production delay analysis confirmed the effectiveness of the hydraulic fracturing program and the validity of the LVA Software.

Jan 1, 2012

By Jun Lu

This paper presents the evaluation, enhancement and comparison of two hydraulic fracturing techniques which were employed to mitigate the impact of a massive sandstone channel on two successive longwall faces. The hydraulic fracturing technique and Longwall Visual Analysis (LVA) software were initially employed to mitigate the impact of thick, massive sandstoneroof during mining of longwall Panel 21. Improved longwall face conditions and productivity were observed as Panel 21 mined through the sandstone channel. However, moderate sandstone fractures and falls at the face were still present in areas where hydraulic fracture influence was not present. Such adverse conditions caused two to three weeks of production delays due to large face cavities, jammed face conveyor and subsequent face gluing. Based on the mining experience in Panel 21, and site-specific roof geology in Panel 22, a modified and more effective hydraulic fracturing program was employed. Fewer well-placed holes were drilled, and larger volume of water was pumped into each hole in order to propagate the individual horizontal pancake fractures over a larger area, thereby enhancing caving and relieving face pressure caused by overhang of the massive sandstone. Longwall Visual Analysis (LVA) software was also employed at Panel 22 to predict the cavity risk index and guide the longwall face crew in double-pulling shields behind the shearer drum. This helped to reduce the tip-to-face distance at the critical spots along the longwall face, which helped mitigate the formation of the roof cavities and failure of massive sandstone onto the face conveyor. Underground observations, face advance rate and face rock delay analysis confirmed that longwall face conditions and advance rate in Panel 22were significantly improved compared to those of Panel 21. Consequently, safety and productivity were improved.

Jan 1, 2014

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By M. Misra

Acid mine drainage from reactive sulfide tailings is a major environmental concern facing the mining and mineral industries. A preventive technique to control acid mine drainage by agglomeration and encapsulation process is presented in this paper. The reactive tailings are agglomerated using Portland cement type I1 as binder. The cold bonded agglomerates after specified curing period are, strong and resistance to weathering. The leaching and weathering experiments have shown that a significant reduction in the concentration of dissolved metals can be observed with the agglomerates as compared to as- received tailings. Addition of small amount of sodium silicate during agglomeration increases the strength and develop good resistance to weathering by forming a glassy coating and elongated crystals within the agglomerates.

Jan 1, 1993

By Angus Campbell, Michael J. Gobla

Numerous techniques for treating, controlling, and preventing acid rock drainage have been applied at the Summitville Mine Superfund Site. Challenging aspects of the remote mine site include the wide-spread occurrence of acid-generating soils and rocks, extensive surface and underground mine workings, and a cold and wet climate. Water treatment was an immediate necessity when the Government took control of the abandoned site in December of 1992. Subsequent reclamation activities have emphasized prevention and control of ARD to minimize future water treatment requirements. A combination of conventional, innovative, and experimental methods are being applied to successfully mitigate ARD at Summitville.

Jan 1, 2000

By S. K. Singh, J. Shepherd

"Feather edging"- a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By S. K. Singh, J. Shepherd

Feather-edging, a major source of injury and fatal accidents in Australia, South Africa and the United States, refers to a phenomenon in which the roof at the goaf edge falls, often suddenly, as a thin wafer of rock that overrides conventional timber breaker lines. The fall may adversely affect a working bord at a distance of 15 m (50ft) or more from the goaf edge. Feather-edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a test in which a concentrated row of fully grouted bolts were used to prevent feather-edging in an Australian pillar- ("total-") extraction coal mine. The test demonstrated that the bolts could resist feather-edging.

Jan 1, 2000