Search Documents

By Gary L. Mowrey

Visible and sometimes audible indications of excessive underground rock pressure such as pillar fracturing, squeezes on chocks, and "roof talk" are familiar to mining engineers. Such signs often precede rock failure on a larger scale and therefore may be used as a warning. Nevertheless, these subjective observations do not provide an adequate means of evaluating the existing rock pressure conditions in a mine. One method which appears to be extremely promising in determining the stability of geologic structures in general is that of monitoring their associated micro seismic activity. Mining engineers generally agree that during the process of rock deformation and failure small-scale seismic ("microseismic") vibrations are produced in the rock itself. These transient vibrations propagate through the rock structure and may be detected at a considerable distance from the failed rock by employing suitable electronic monitoring equipment. Hardy (1) has presented a detailed review of microseismic research in the mining, petroleum, and geoscience areas, and it is apparent that relatively little application of micro seismic techniques have been made in coal mines. This is especially true in North America since here most coal mines are fairly shallow and consequently are not generally subjected to excessive stresses. Furthermore, strict Federal and State mining laws limit the use of electrical equipment in coal mines complicating the use of the necessary monitoring facilities. In terms of both mine safety and economics, monitoring microseismic activity appears to be invaluable in the detection and location of over-stressed pillars and unstable roof conditions caused by development and production work. In 1970 The Pennsylvania State University Rock Mechanics Laboratory became involved in a research project, sponsored by the U.S. Bureau of Mines, to investigate the feasibility of using microseismic techniques to detect and to locate potential regions of instability around a longwall coal-mine operation [Hardy and t10wrey (2); Mowrey (3)]. In this study geophones (velocity gages) located in an array of shallow boreholes drilled from the surface above the active area of the longwall were employed to detect microseismic activity, and a mobile micro-seismic monitoring facility was used to condition and record this data for later analysis. This project is unique in that measurements were made from near-surface geophones rather than geophones installed on the mine itself. Two advantages are apparent, namely that (1) there are no electrical limitations on the monitoring system and that (2) mining operations can continue normally because there is no monitoring equipment or cables in the mine.

Jan 1, 1978

By H. Reginald Hardy, Gary L. Mowrey

Field studies were conducted over a longwall coal mining operation to investigate the feasibility of using microseismic techniques to detect and to locate any areas of instability in the vicinity of the longwall. An array of geophones buried at depths of 3 to 8 m from surface were positioned approximately 130 m above the active area of the longwall panel. A mobile microseismic monitoring facility amplified, filtered, and recorded the microseismic activity sensed by the geophones. Microseismic events were detected at depths of at least 130 m and at horizontal distances in excess of 250 m from the source. Most events, which resembled decaying sinusoidal transients, had frequencies of 10 to 100 Hz, and particle velocities of 1 to 8 pm/s. Source locations for the 150 largest events were computed using a least-square travel-time-difference method. Both isotropic and unique wave propagation velocity models were considered when evaluating the source locations. Most of the events were computed to be within ± 30 m vertically of the coal seam and ± 15 m horizontally of the longwall face, when the unique velocity model was employed.

Jan 1, 1980

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

By P Dean, M Elmouttie, Y Duan, X Luo

Slope instability is one of the major concerns in open pit mining operations. A significant collapse of the pit wall can result in injuries, damage to machinery and interruptions to production. A broadband microseismic monitoring technique has been developed for diagnosing the healthy condition of a target slope area. This technique has been successfully applied to an open pit mine in Chile. Our research has found that this microseismic monitoring technique can be used in open pits for tracking and locating a falling rock that is rolling on a slope, if a dedicated seismic sensor network has been established. In collaboration with other monitoring techniques (radar, laser scan, aerial photography), more accurate determination of rock rolling trajectories can be obtained. In this paper, an example of using the CSIRO microseismic monitoring technique at an open pit mine is presented. Results from an experiment where we used the microseismic technique for determination of the trajectory of a rockfalling on a slope are also presented.

Nov 8, 2021

By Wilson Blake

Rock deformation and failure taking place around underground openings is usually both accompanied and preceded by the phenomena of rock noise or microseismic activity. These small-scale releases of seismic and acoustic energy can be detected with special geophysical monitoring equipment. Use of this equipment allows one to look inside a rock mass to determine how an opening is behaving under the applied loading system. Microseismic equipment and monitoring techniques are briefly reviewed, and use of the microseismic method as an engineering tool in monitoring rock structure stability is illustrated by case histories. Examples cited range from evaluating roof stability using single-channel portable equipment, to rock burst monitoring using sophisticated computer controlled, multichannel monitoring systems.

Jan 1, 1983

By G. R. Corbett

Between 1977 and 1984, No. 26 Colliery, at Glace Bay in the Sydney Coalfield, suffered from a series of 37 rock/gas outbursts. These events were characterized by the complete pulverization of a sandstone which was propelled into the mine roadway and an associated release of methane gas. The events began to appear at a depth of 700 m and increased in intensity and damage to the excavation as the mining depth increased. At the time of the closure of No. 26 Colliery (as a result of an unrelated fire), these outbursts were the subject of intensive investigation. Although No. 26 is now closed, there is concern that similar events could appear at Phalen Colliery where current development work is proceeding at a depth close to the 700 m threshold. Past investigations into rock/gas outbursts included studies of in situ stresses, the simulation of outburst events in the laboratory, investigations into the potential for destressing an& degassing of problem sandstone and the development of numerical models to assist in the design of openings in outburst prone ground. However, despite this work, methods of predicting outburst conditions are presently limited to examination of probe hole cores for core discing, and methods of working under such conditions are limited to boring and firing and using volley firing techniques to initiate any outbursts while workers are safely out of the heading. During this investigation of worldwide occurrences of this phenomena, literature obtained suggested that outbursts might generate microseismic precursors. An intrinsically safe (IS) microseismic monitoring system was designed and developed based on CANMET's rockburst monitoring system currently in use in hardrock mines, and installed in a development roadway at the deepest extent of the Phalen Colliery. The system will record microseismic activity associated with development work to try to identify characteristic precursors of outburst-prone conditions. This paper describes the steps taken to identify a microseismic system suitable for use at Phalen colliery, of which part of the requirement was that it be IS and approved for use in the Sydney Coalfield. The modifications to the selected system are described, along with its capabilities and the preliminary results of its performance over the first few months of use.

Jan 1, 1994

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

By M. Guarascio

Microseismic monitoring of mining areas is a developing technique, described here for the Belvedere Spinello Mine, southern Italy, where dissolution cavities in the mining area have proved problematic. The preliminary condition for locating seismic impulses has been found to be a reliable seismic ground model. Ground signals are continuously recorded by means of data from piezometric wells, for sinkhole data, and linked gephones, for microseismic data. A computer system has been implemented to collect, analyse and interpret the incoming signals consequently, identification and classification of hypocentres of activity is facilitated, with advantages in terms of safety, preventing harmful side-effects, including rock bursts, and for environmental conservation.

Jan 1, 1987

By Peiwei Xiao, Xiang Li, Biao Li, Haoyu Mao, Nuwen Xu

As an advanced method of rock engineering construction safety monitoring, microseismic monitoring technology can monitor the micro-fracture of rock masses within an effective range, and then perform forecast analysis of rockburst, cracking, falling blocks and other disasters. Although the application of microseismic monitoring technology has become more mature, how to improve its application efficiency remains to be further studied. At present, artificial intelligence has been extensively developed, and the use of intelligent algorithms to improve the efficiency of rockburst forecast can provide a valuable reference for the safe construction of underground engineering. To this end, this paper proposes a microseismic multi-parameter rockburst early warning model based on dynamic Bayesian networks. First, the sensitivity of microseismic source parameters to rockburst forecast is analyzed based on microseismic monitoring data and actual rockburst information of a hydropower station. Second, the main seismic source parameters and their data are selected and imported into a dynamic Bayesian network for learning to obtain the rockburst forecast model. The model is confirmed in its self-validation and K times cross-validation, and the receiver operating characteristic curve of the model is also analyzed, it is found that the area under the curve is close to 1, indicating that the model has good accuracy. Finally, the analysis of the influence strength of the parent and child nodes in the model reveals that the moment magnitude and source scale are the most sensitive parameters, which can be used as an important reference for rockburst forecast.

Apr 26, 2022

By V. Shumila, T. Butler

Microseismic monitoring systems listen to a rockmass and record ground vibrations associated with brittle rock fracture. Modern systems record continuously and can identify as many as one thousand small and possibly larger magnitude events occurring each day from induced stress change and redistribution. This paper presents examples of the real time use of microseismic information in mining applications. It shows how alerts can quickly identify large magnitude events or unexpected clusters of seismicity and how seismic re-entry protocol can help to improve safety decisions. Additionally, newly developed advanced analysis techniques applied to mine seismic data sets are shown including the use of clustering methods to see into a cloud of seismic data to identify significant activity and quantify possible planar features. The use of source parameter trend analysis is shown to be a beneficial method for interpreting changes in relative stress levels. Seismic moment magnitude distributions are analyzed using the TGR (Truncated Gutenberg Richter) and TMD (Tapered Moment Distribution) methods to estimate bvalue and expected maximum magnitude. Seismic hazard analysis is shown as a useful way to simplify a dataset and highlight seismic hot spots. The rockmass response to excavation is a complicated spatial and temporal process and microseismic monitoring is a method that can be used to help understand the location and mechanics of failure occurring in the rock ultimately helping to improve safety and productivity at a mine site.

Jan 1, 2015

By Pavel Vasak

Microseismic monitoring is becoming standard practice in the Canadian mining industry, particularly as mines get deeper. Full-waveform microseismic systems allow the operator to distinguish the event source mechanism, e.g., blast, shear slip or stress-induced fracture. At mine sites that heave a microseismic system operator blasts are manually identified by comparing the event waveform traces to the morning blast logs. However, this procedure is not routinely done at sites where a system operator is not present and this can lead to misinterpretation of the data at a later stage, particularly where the interpretation is outsourced, often many years later. It is critical to improve the microseismic data quality and consistency for processing and interpretation with a reliable technique to filter out blasts and blast related seismicity. This paper presents the development and implementation of a simple blast identification and filtering routine. The routine was developed specifically for Vale?s Creighton Mine about a decade ago, but is made sufficiently general so that it can be used at any mine site with an ESG (Engineering Seismology Group Canada) based full-waveform microseismic systems. The routine is strictly a post-processing procedure developed for use with the Access database data structure used by ESG. The algorithm was tested at Creighton Mine and a success rate of 80 to 90% was achieved, when compared to manual blast picks.

Oct 1, 2010

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By N. Economou

Temporary local seismic networks were installed in western Crete, in central Crete, and on Gavdos, an island south of western Crete, in order to image shallow seismically active zones of the Hellenic subduction zone. Data acquisition was divided in four campaigns through the years 1996 to 2001. More than 4000 events in the magnitude range between 0.5 and 4.8 were detected and localized. The resulting hypocenter distribution allows the localization of seismically active zones in the area of central Crete from the Mediterranean Ridge to the Cretan Sea. The comparison of the hypocenter distribution and the structure has allowed intraplate and interplate seismicity to be distinguished. A southwards dipping zone of high seismicity within the Aegean lithosphere is found south of central Crete in the region of the Ptolemy trench. Between 20 and 40 km depth beneath central Crete, the Aegean lithosphere appears to be seismically inactive. Especially for the year 2001, 1560 events were localized, by the seismic network installed on Messara, central Crete. Most of the seismic events were located, as expected, in the South region of central Crete. National Observatory of Athens (NOA) maintains a permanent seismic network in Greece. In this work a comparison of the earthquake epicenters obtained from both the NOA network and the BOCHUM-TUC network is presented.

Jan 1, 2006

By K Thorpe

Amorphous silica deposits have been identified at Tikitere and Taheke near Rotorua. Two areas at Tikitere have been surface sampled and drilled to establish a resource of amorphous silica in excess of one million tonnes. A pilot plant was established to develop a process to manufacture a high quality super pozzolanic material. This development process took two years before a commercial product was introduced to the construction industry in 1996. The amorphous silica product, marketed as Microsilica 600, is used as a pozzolanic material to produce high quality strong and durable concrete, sprayed tunnel linings, mortars and grouts. Microsilica 600 has been used locally and exported to 11 countries.

Jan 1, 1999

By M. A. EI Zeky, A. E. El-Nikbaily, M. A. Shahin

"Possible mechanisms of microsilica dust formation and factors affecting its quantity have been discussed. General mathematical models to predict the dust quantity based on electrical and coke consumptions, and flue gas temperature as functions of silicon recovery in the process and silicon content of the alloy have been established. It has also been shown that the flue gas temperature can be used as an additional process control parameter. Comments are made on the effect of the dust formation on the whole process economics and it is pointed out that the formed microsilica dust is a valuable by-product and not an industrial waste. INTRODUCTIONFerrosilicon is produced in electric arc furnaces with submerged electrodes. The charge mixture consist s mainly of quartzite, coke as the reducing agent and iron chips. The products are ferro silicon and carbon monoxide, various other volatile materials, water vapour and silicon monoxide gas. Carbon monoxide and silicon monoxide oxidize at the charge surface when mixed with air entering through the furnace hood openings. The off-gas contains a considerable amount of dust, which is mainly very fine particles of silica formed as a result of oxidation. The emission of dust containing gases to the atmosphere causes serious pollution problems to the environment. Therefore, the control of the formation of the dust, preventing it from escaping to the atmosphere, and dealing with this very fine dust collected from the flue gases represent important technological and economical parameters in the ferrosilicon production industry.This paper is concerned with the relations between the quantity of formed micro silica dust, as a function of both silicon recovery and silicon content in the alloy, and various other technological parameters; and their possible effects on the energy consumption and economics of the whole process."

Jan 1, 1989

By O. A. Ojo, E. Anisimov, A. K. Khan

Electro-spark deposition (ESD) has recently generated a great deal of interest in processing aerospace materials. This is due to its potential for joining and repairing difficult-to-weld precipitation strengthened nickel-based superalloys without having problems of welding cracking that often plaque these materials. The short duration of current pulses involved in the process combined with the intermittent contact results in extremely rapid thermal cycle that produces nearly no heat affected zone in the substrate material. The microstructure of electro-spark deposited superalloy was meticulously studied in this work by scanning electron microscopy (SEM) and analytical transmission electron microscopy (TEM). The results show that in contrast to general assumption, the extreme rapid cooling rates involved in the ESD process did not produce partition-less solidification that is devoid of second phase microconstituents in the material. The secondary microconstituents were found formed along the intercellular regions of the solidification microstructure. The nature of these particles and the possible implication of their formation on mechanical properties of ESD processed material are reported and discussed.

Jan 1, 2015

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The ever increasing number of automobiles and the consequential increase in consumption of tires have generated a pressing environmental issue, concerning the disposal of unserviceable tires. The worldwide disposed of waste tires is approximately 1 billion units per year and this amount is expected to increase by 2% each year. This work presents a microstructural characterization of nanomaterials synthesized in a catalyst system from the effluent of burning waste tire chips in a horizontal two-stage laminar-flow furnace. Controlled combustion of waste tire chips took place at temperatures of 900 or 1000 °C, and stainless steel meshes were used to synthesize the nanomaterials at 1000°C. Produced materials were analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The catalyst meshes were covered by materials with diameters of 20 to 200 nm and lengths of about 40 µm. They possessed structures similar to those of carbon nanotubes.IntroductionThe motor vehicles on the road have been increasing annually. World motor vehicle production in 2009 approached 62 million units. Consequently, the consumption of tires has also been on the rise; about 1.4 billion units were produced around the world in 2007 [l]. The disposal of scrap tires is a serious environmental problem. The worldwide disposed of waste tires is almost 1 billion units per year with an expected increase of around 2% each year. However, less than 7% of produced waste tires are recycled (excluding reuse, retreading or incineration). The waste rubber tires are a thermoset polymer, which cannot be reprocessed like thermoplastics polymers, therefore the recycling of this material requires special techniques that demand big investments [2, 3].A solution to the disposal of waste tires is the sequential pyrolysis/combustion process. Past research showed that waste tires are an attractive potential fuel due the high heating value (29-3 7 MJ/kg), which is comparable, or even higher to those of typical bituminous coals [ 4, 5]. Pyrolysis is a process wherein the material is thermally decomposed at elevated temperatures at the absence of an oxidizing gas. Combustion is characterized by the addition of the oxidizing gases during the process. Several studies indicate that the pyrolysis and combustion processes for the tires treatment have a great energy conversion potential [4, 5, 6]."

Jan 1, 2011