Search Documents

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By Fathi Habashi

Tras pasar revista a diversos ejemplos de procesos químicos propios de la metalurgia extractiva —referencialmente clasificados como piro, hidro y electrometalurgia—, el autor muestra cómo, por ser más eficientes, económicas y/o cumplir con las modernas regulaciones ambientales, las últimas tecnologías vienen desplazando gradualmente a las más antiguas. Tal es el caso de las recientes investigaciones sobre una nueva tecnología para la producción electrolítica de aluminio que excluye la reducción de carbono, con el fin de eliminar la producción de CO2.

Sep 30, 2020

By Noel Díaz Bernal

El presente texto señala las concentaciones de metales preciosos, oro y plata dentro de las menas comunes de metales básicos de plomo y zinc en vetas dentro de volcánicos terciarios.

Sep 1, 1974

By J. P. Rodier

Despite the good years that the non-ferrous business is now enjoying, one should not forget that in this business growth rates are low, fixed assets are high and prices are more cyclical than in other businesses. Increasing environmental concern puts the industry under pressure. Lead and zinc companies are now profitable and profitability in the next ten years will depend on size of units, location, and choice between new technology and upgrading current ones. Implementation of Metaleurope was a strategic move. It produced a company of sufficient size to achieve new steps in cost cutting and yet remain flexible enough to deal with rising variety of primary and secondary raw materials.

Jan 1, 1990

By Edelink Efrain Tinoco Falero

Na atualidade a produção e a utilização de DRI estão aumentando nos países desenvolvidos, principalmente devido à redução do preço do gás natural e do sucesso da nova tecnologia de extração de gás de xisto. Os custos operacionais e os problemas ambientais são, efetivamente, os fatores tecnológicos importantes a serem considerados na otimização da produção de DRI. Portanto, o teor de carbono do DRI tornou-se essencial em virtude da capacidade de gerar energia química no banho de aço, complementando assim a eletricidade em FEA, e as contribuições exotérmicas da oxidação de Si e C nos conversores LD. Este trabalho faz parte de um programa completo de cooperação entre a companhia de mineração Samarco e o Grupo de Siderurgia da PUC-Rio, lidando com as equações cinéticas da metalização e carburização simultânea em fornos de redução direta. Para este efeito, o reator foi dividido em três zonas internas: Redução, Transição e zona de resfriamento. Além disso, também foram consideradas três regiões concêntricas: periférica, média e centro. Á partir desses resultados, para um tipo de pelotas RD específico, mistura de gases utilizados nas instalações industriais e similar flui-dinâmica do processo, as equações cinéticas de metalização e carburização foram estabelecidas para cada zona. Um programa computacional METCARB, totalmente baseado nessas equações cinéticas, foi então concebido. Finalmente, uma validação adicional procedeu-se tendo em conta duas corridas operacionais industriais.

Aug 17, 2017

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By K. E. Gonsalves, G. M. Chow

"Nanostructured powders (particle diameter of 1 - 100 nm) have uses in electronic, magnetic, structural, thermal applications as well as advanced processing of materials. Among many methods of making nanostructured powders, chemical routes offer many attractive features such as feasibility of cost-effective bulk quantity production, design of chemistry at the molecular scale, and chemical homogeneity of the powders. In this talk, two systems of chemically synthesized nanocomposite powders are presented, namely, granular magnetic materials of Fe-Cu and Co-Cu, and thermal-structural materials of AIN-BN. Synthesis and processing, characterization and properties of these materials are discussed.IntroductionNanostructured powders (particle diameter of 1 - 100 nm) are attractive materials because of many useful properties (e.g. catalytic, optical, magnetic etc.) and processing advantages (e.g. lower sintering temperature) [1]. There are many methods of making nanostructured powders, for example, physical and chemical vapor deposition, mechanical attrition, and solution chemistry [1, 2]. A common method of making composite powders involves the grinding, mixing and blending of constituents powders, but it has the limitation of inhomogeneous mixing. Chemical routes have many useful features. Using solution chemistry, precursors can be molecularly tailored and homogeneously mixed at the molecular level. The chemical approach may result in better properties of the final product. Compared to vapor-phase fabrication techniques, chemical routes are more cost-effective in producing large quantity of material. In addition, control of particle size, size distribution and stabilization of the nanoscale particles against agglomeration can be more effectively manipulated via solution chemistry.In this paper, we present an overview of some of our work in nanocomposite powders prepared by solution chemistry. Metallic systems of FeCu and Co-Cu, and ceramic system of AIN-BN are discussed. The powders were characterized using x-ray diffraction (XRD) , scanning electron microscopy (SEM), conventional and high resolution transmission electron microscopy (TEM, HRTEM), vibrating sample magnetometry (VSM), inductively coupled plasmaatomic emission spectroscopy (ICP-AES)."

Jan 1, 1994

Although copper production established a new record, lead and zinc registered gains, and iron production held steady, the mixed trend in metallic and nonmetallic mining and generally lower prices in 1961 resulted in a net decline in the total value of domestic mineral production. According to preliminary estimates from the U.S. Bureau of Mines, the value of metals produced in this country during the year was approximately $1.9 billion, a decrease of $117 million from 1960; the value of nonmetallics was about $3.7 billion, a $14 million decrease. The following report of mining and mineral developments during 1961 is based on USBM and industry sources. Aluminum Output Dips from 1960 Record Government reports indicate that the domestic primary aluminum industry produced approximately 1,880,000 tons, equivalent to 77% of this nation's capacity. This production is about 6% below the 1960 record output of 2,014,498 tons. Shipments of primary metal ingot slightly exceeded the quantity produced.

Jan 2, 1962

By Craig Cina

Transporting goods from producers to consumers is a fundamental part of the US economy. The demand for transportation closely reflects the economic health and well-being of the nation's industrial, commercial, and agricultural sectors. The inland waterway barge industry has traditionally played a key role in transporting needed commodities to industries on an economical basis. Barges account for 10% of the domestic intercity tonnage carried by all transportation modes. Water carriers operating on inland waterways hauled more than 450 Mt (500 million st) of cargo in 1980-up from 428 Mt (472 million st) in 1970. Inland Waterway Shipments Metallic and nonmetallic minerals comprise one of the largest commodity groups moved on inland waterways. As illustrated in Table 1, metallic and nonmetallic mineral shipments accounted for more than 69 Mt (77 million st), or nearly 15% of all commodities shipped in 1980. Putting this tonnage in perspective, coal and petroleum represent the two largest commodities moved on inland waterways. In 1980, petroleum and petroleum products accounted for 138 Mt (152 million st), or 28% of all commodities shipped. Similarly, coal represented 120 Mt (132 million st), or 25% or all commodities shipped. Even though shipments of metallic and nonmetallic minerals are smaller than coal and petroleum, they still account for a sizeable portion transported. The inland barge industry moves a variety of metallic and nonmetallic minerals ranging from manganese ores to building cement. Minerals transported by barge include: • iron, copper, bauxite, and manganese ores for metal production; • lime and limestone for construction and electric utility scrubbers; • phosphate rock, natural fertilizers, and gypsum for agricultural needs; • sand, gravel and crushed rock, clay, asphalt, tar, and pitches, and building cement for construction purposes; and • a host of other minerals to meet industrial needs. A few mineral commodities are responsible for a large proportion of waterborne mineral shipments.

Jan 10, 1982

By Marvin J. Udy

THREE GENERAL REASONS exist for applying metallic coatings to steel: to improve its appearance, to resist corrosion, and to resist wear and abrasion. Coating steel with other metals to improve the appearance and to resist corrosion is an old practice; coating for resistance to wear is one of the newer development's' that has become of importance with the development of chromium plating. Coating for improvement in appearance is practically confined to electroplating. Metals like copper, nickel, silver, chromium, cadmium, zinc and tin, because of their pleasing color, are used for this purpose. But these metals are never quite corrosion-proof, except cadmium and zinc, when applied directly to steel. Improvement in color or appearance must be permanent and therefore corrosion-resistant and tarnish-proof. For this reason, with the exception of cadmium, zinc and tin, the above metals are used in combination to obtain appearance and resistance to corrosion. Resistance to tarnish is dependent on the property of the particular metal. Chromium, being nontarnishable, has made it possible to obtain combination coatings of copper, nickel and chromium, copper and chromium, or nickel and chromium, which improve the appearance and also resist corrosion and tarnish. Such coatings find a wide field in decorative work particularly the copper-nickel-chromium combinations, and when properly applied are very satisfactory.

Jan 1, 1932

By Shun-ichi Satoh

THE electric arc welding of cast iron has been studied by Braune, Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer, Candy, Neese, Miller, Carter, American Welding Society, Namack, Lebrun, Achenbach, Jansson, Kochendörffer and others.1 The writer of this paper has been able to obtain a series of cast irons, from gray to white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (SiC) and graphite (C). In this work, he has found the curious phenomenon of barium- carbonate.

Jan 1, 1929

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By Aline Lima da Silva

The reduction in SOFC operating temperature due to recent development in materials and fabrication techniques enables the use of ferritic stainless steels as interconnects for SOFCs. Ferritic stainless steels offer many advantages over traditional ceramic interconnects, such as higher thermal and electronic conductivity, as well as relative ease of fabrication. However, the formation of chromium oxide on ferritic stainless steel results in an increase in ohmic resistance and can lead to the loss of cathode catalytic activity (due to Cr volatilization, with cathode poisoning). The oxide growth depends on several factors, such as steel composition, temperature, oxygen partial pressure. In this way, knowing the phase stability, the oxidation behavior of the material and the oxidation kinetics is of great interest. In this context, a thermodynamic study of the oxidation of ferritic stainless steel 430 under oxidizing atmosphere (cathode), at the temperature of 750ºC, is carried out. As one can see, the thermodynamic system can be very complex, involving several phases (chromium oxide, (Fe,Cr,Mn)3O4 Spinel, iron-chromium oxides, etc.). The effect of oxygen partial pressure and alloying elements on phase distribution is evaluated. Thermodynamic modeling is compared with experimental results from literature.

Aug 8, 2018

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By T. R. Carter, A. C. Colvine

"Rocks of the Grenville Province in southeastern Ontario are currently largely dismissed by many geologists as having little or no potential for discovery of significant deposits of metallic minerals. The present study demonstrates that the area contains numerous deposit types which elsewhere are major metal producers. Therefore, there is significant unrealized potential, especially for gold, zinc, uranium, and possibly copper.The variety of deposits of metallic mineralization include stratiform zinc in marbles; stratabound base metal sulphides in volcanic and sedimentary hosts; gold-quartz veins; quartzmagnetite iron formation; copper-nickel and iron-titanium in intrusive rocks; magnetite skarns; molybdenum in skarns and pegmatites; uranium and thorium in pegmatites, veins, and calc-silicate gneisses; hematite veins; dolomite marbles (magnesium); and barite-jluorite-celestite-galena-calcite veins. There has been significant production of iron, lead, zinc, magnesium, gold, silver, and uranium.The vast majority of the metallic mineral deposits are confined to late Precambrian supracrustal and related intrusive rocks of the Grenville Supergroup. Many of the deposits are stratiform and/or stratabound and occur within units toward the top of major volcanic successions and in the lower portions of younger carbonate-clastic sedimentary successions.Processes responsible for mineral concentration in the area include: (I) syngenetic hydrothermal activity related to both volcanism and sedimentation; (2) epigenetic processes related to diagenesis, regional metamorphism, and igneous intrusive activity; (3) magmatic processes related to igneous intrusions; and (4) supergene concentration and enrichment. The genetic classification of the mineral deposits presented is based on observed geological relationships and these interpreted geneses. The deposit types have counterparts in volcanogenic and sedimentary exhalative, Mississippi Valley type, magmatic, contact metasomatic, and lode gold deposits. Many of the exploration criteria for deposits of these types may be applicable in the Grenville Province, despite the generally high metamorphic grades and complex deformation."

Jan 1, 1985

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991