Search Documents

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions' it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By F. L. Meng, C. S. Henkel, R. M. Alchalabi

For secondary aluminum producers to maintain a profitable melting operation, five technical factors have to be taken into account from the initial furnace building decision to the final operation and production. These factors are furnace design, furnace equipment selection, furnace control, furnace charge selection and inventory, and furnace operation. Any of these five factors, if not chosen or performed wisely, will likely result in sub-optimal melting operation. As a result the MeltSim melting optimization package has been developed by the collaborative effort of Chinook Sciences and AMCS Corporation to take into account these five factors. The package is a mixture of hardware, software, science and experience. The package incorporates years of reverb furnace operational observations, start-up installations, furnace operator experience and furnace physiochemical mathematical model development. The optimization package enables aluminum producers to design new furnaces, select and place proper equipment, optimize existing furnace operations, and convert air-fuel installations to oxy-fuel. The package provides furnace operation monitoring and advisory signals, and furnace automatic optimal control to furnace operators, shift supervisors and plant managers, all customized, based on plant and melter need and ease of information management.

Jan 1, 2000

NIM reports Report no. 1970 List of unrestricted NIM publications issued from 1966 to 1978. (30th Jun., 1978). Report no. 1976 The preparation and certification of two samples of chromium ore. (9th Sep., 1978). Report no. 1982 The resistivity of mixtures of Mamatwan manganese ore and reducing agents. (31st Aug., 1978). Report no. 1984 Commissioning of the AEI MS702 mass spectrometer. 31st Aug., 1978). Metallurgical slags The Basic Science Section of the Canadian Institute of Mining and Metallurgy is sponsoring an International Symposium on Metallurgical Slags, which is to be held in Halifax, Nova Scotia, during 24th to 28th August, 1980. Mining machinery An international conference on mining machinery is to be held in Brisbane, Australia, from 2nd to 6th July, 1979.

Jan 1, 1979

Jan 1, 1894

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS t ARE ASSOCIATES THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY THE FIGURES AT THE END OE THE ADDRESS INDICATE THE YEAR OE ELECTION HEAVY FACED T1 PE SIGNIFIES HONORARY MEMBERSHIP *ABADIE, EMILE R , Min Engr P 0 Box 83, Berkeley, Cal '76 *ABBE, CLEVELAND, JR, Geol Aid, U S Geological Survey, Washington, D C '00 *ABBOTT, AI ARTHUR, Cerro de Pasco Mining CO , Cerro de Pasco, Peru, So America '95 *ABBOTT, ARTHUR V , Electrical Engr , Westinghouse, Church, Kerr & Co , 8 Bridge St, New York, N Y '82 *ABBOTT, CLARENCE E, Chief Min Engr, Care Fayal Mine, Eveleth, Minn '04 *ABBOTT, JAMES W , Min Engr , Special Agent, Rocky Mountain and Pa¬cific Coast Division, U S Dept of Agriculture, "Tile New Markham," Denver, Colo '94

Jan 1, 1910

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05 ? ACKER, E. O'C., Supt., Treatment Dept., Bethlehem Steel Co., So. Bethlehem, Pa. '86

Jan 1, 1910

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917

Jan 1, 1902

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS t ARE ASSOCIATES THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION HEAVY FACED TYPE SIGNIFIES HONORARY MEMBERSHIP ` *AARONS, JULIAN B , Mine Supt, The Boulder Deep Levels, Ltd , Boulder, Western Australia, '05 *ABADIE, EMILE R, Cons and Min Engr, 1004 James Flood Bldg, San Francisco, Cal '76 *ABBE, CLEVELAND, JR, GeOl Aid, U S Geological Survey, Washington, D C '00 *ABBOTT, AI ARTHUR, Cerro de Pasco Mining CO , Cerro de Pasco, Peru, So America '95 *ABBOTT, ARTHUR V , Electrical Engr , Westinghouse, Church, Kerr & CO , 8 Bridge St, New York, N Y '82 *ABBOTT, CLARENCE E, Chief Min Engr, Care Fayal Mine, Eveleth, Minn '04

Jan 1, 1910

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917

By AIME AIME

HOLDING the annual dinner-dance of the Institute at the Waldorf-Astoria had become such a tradition that there was widespread regret when it became known that the demolition of the building to make way for a huge office structure would perforce bring to an end the long and enjoyable series of gatherings our Institute had held there. This year the . Commodore was the place at which it was held and the commuters on the New York Central and the New Haven railroad systems, at least, found it a more convenient place for them. Except for the famous "Hoover" dinner, which will probably set a mark for all time, it was the largest dinner the Institute held, 1000 being present, and it taxed the facilities of the hotel to the utmost.

Jan 1, 1930

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve -Engineers. AMBLER, HARRY A., Second Training Camp, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22c1 Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers' Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 10, 1917

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDREWS, CLARENCE W., 2d Lieutenant, 12th Batt. Infantry Replacement Regiment. ANDREWS, JOSEPH C., Ordnance Dept., U. S. A. ARLUCK, A. A., Headquarters, 1st Corps of Artillery, A. P. O.. No. 759, A. E. F.

Jan 9, 1918

BARBOUR, PERCY E., Deputy Supt., (Captain), New York State Troopers; Captain, 22nd Regiment, N. Y. N. G. BARLING, 1i. B., 1st Lieutenant, Engineer Officers' Reserve Corps. CHAPMAN, R. H., Major, Engineer Officers' Reserve Corps. DUNN, THEODORE S., 1st Lieutenant, Engineer Officers' Reserve Corps. DWIGHT; ARTHUR S., Major, Engineer Officers' Reserve Corps. FORBES, CARROLL R., Captain, Engineer Officers' Reserve Corps. GOODSPEED,. G. E., JR., 1st Lieutenant, Engineer Officers' Reserve Corps.

Jan 7, 1917

(This list. includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. A complete list will he found in the Year Book mailed with this Bulletin. Another Honor Roll is maintained in the reception room of the Institute.) ALDEN, HERBERT W., Lieutenant-Colonel, Ordnance Dept. ALDER, ALFRED; Engineers' Reserve Corps. ALFORD, NEWELL G., Sergeant, Bureau of War Risk Insurance, Headquarters 84th Division. AMBLER, HARRY A., Lieutenant, 30th Infantry. ANDERSON, GEORGE K., JR., Sec. C, 1st Co.; 3d Officers' Training Camp. AYER, -FRANK A., 1st Lieutenant, 43d Squadron, 3d Prov. Regiment, Aviation Camp.

Jan 3, 1918

AARONS, J. BOYD; Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve Engineers. AMBLER, HARRY A., Second Training Camp,, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy' Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers' Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 11, 1917

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) *AMBLER, HARRY A., 1st Lieutenant, 0. R. C., 30th Infantry, A. E. F. BAKER, R. F., Private, Intelligence Section, Headquarters 90th Division. *BARTON, L. A., Captain, 604th Engineers. *BATTEN, H. L., Lieutenant, Canadian Engineers, C. E. F. *BENSEL, J. A., Major, U. S. Reserves. BIRKETT, HOWARD, Lieutenant, Aviation, U. S. Signal Corps. BLOOMFIELD, E. C., Lieutenant, 1st Canadian Tunnelling Co. BOOTH, L. E., Watertown Arsenal, Det. E. 0. C., N. A., Watertown, Mass. *BOWMAN, REGINALD G., 1st Lieutenant, Engineers, U. S. R., Int. Ord. Dept. No. 4, A. E. F. *BRADLEY, CLARENCE I., Convois Automobile Section 585,. S. S. U., P. A. R., B. C. M.

Jan 7, 1918