Search Documents

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By George D. Haley

This report will be given in two sections. The first sec¬tion outlines techniques and equipment to form almond shaped fluorspar briquettes by means of briquet presses, and the second section outlines techniques of the balling disc. PART I - BRIQUET PRESSES Fluorspar has been briquetted for a number of years and the so called "peach pit" briquet is known to many steelmen. Present production is estimated at over 100,000 tons annually. Slide 1 shows an assortment of various sizes and shapes of briquettes. It is possible to form fluorspar into almost any configuration of briquet. For safety on the melting floor, pillow type briquets are preferred. Ease of mechanical handling and durability of the product are facil¬itated by an almond shape. The dimensions of the almond can vary from 1-in. to 1-1/2-in. in length, from 13/16-in. to 1-in. in width and from 1/2-in. to 1-in. in thickness. The type of equipment to pro¬duce almond shaped fluorspar briquettes is shown in Slide 2. Here we have a Komarek-Greaves and Company 300 ton briquettor equipped with almond rolls. This machine is capable of producing fluorspar briquettes at a rats of 30 tons per hour with power consumption of 35 hp per ton par hour.

Jan 1, 1969

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

By Weldon Li

Outline ?Introduction and Motivation ?Previous Research ?Details ?Findings ?Current Multi-Piece Mining Wheel Research ?Methodology ?Preliminary findings ?Current and Future Activities ?Summary and Closing Remarks

Oct 1, 2010

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

This paper describes the mechanical and electrical maintenance activities as practised at Isa Mine. The principles of preventative maintenance adopted are described as well as the basis of maintenance cost control.

Jan 1, 1978

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By Dmitri Goljandin, Jaan Kers, Xiangjun Zuo, Lifeng Zhang, Priidu Peetsalu

"In this paper, the mechanical milling of the electronic wastes was carried out. The metal parts and plastic parts were roughly separated. The final plastic powder size could be as small as ~100 µm. Then the pyrometallurgical recycling Printed Circuit Boards (PCB) was executed. The mechanisms of thermal degradation and combustion are investigated using TG/DTA and MS. Some chemical powders, such as Na2CO3, NaHCO3, NaOH and CaCO3 are used to control the exhausted toxic gas such as Br2. Introduction Waste electric and electronic equipment (WEEE), or electronic wastes (E-wastes), has been taken into consideration not only by the government but also by the public due to their hazardous material components [1-3]. From the point of material composition, electronic wastes can be defined as a mixture of various metals, particularly copper, aluminum, and steel, attached to, covered with, or mixed with various types of plastics and ceramics [4]. Precious metals have a wide application in the manufacture of electronic appliances, serving as contact materials due to their high chemical stability and their good conducting properties. Platinum group metals are used among other things in switching contacts (relays, switches) or as sensors to ascertain the electrical measurand as a function of the temperature [5]. Table 1 [6] gives examples of the metal composition of different electronic scraps from literatures. Additionally, non-ferrous metals and precious metals content have gradually decreased in concentration in scraps. The value distributions for different electronic scrap samples are shown in Table 2 [6], where the metal price data are from London Metal Exchange (LME) (Octoebr 2007). It can be seen that for cell phones, calculators, and printed circuit board scraps, the precious metals make up more than 70% of the value, for TV boards and the DVD player they still contribute to about 40%. This indicates that the major economic driver for recycling of electronic waste in industry is from the recovery of precious metals. Behind the precious metals come copper and zinc, while Al, Pb, and Fe are less value. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials."

Jan 1, 2008

By J. T. McGrath, R C. A Thruston

The structural changes which take place in polycrystalline copper under the action of alternating cycles of torsion stress were studied, using the optical microscope and the X-ray dif-fraction camera, and an attempt was made to correlate them with changes in the shape of the cyclic stress-strain curve. It was found that the period of work-hardening was less than one per cent of the fatigue life, and that persistent surface marking, which are assumed to be incipient or actual microcracks, occur upon completion of work-hardening. X-ray diffraction patterns revealed considerable grain distortion at the completion of work-hardening in specimens cycled at a high strain amplitude. This distortion became progressively less as the strain amplitude de-creased. Mechanisms for the completion of work-hardening and the formation of microcracks are discussed.

Jan 1, 1962

By Sergio N. Monteiro

Natural lignocellulosic fibers are successfully replacing synthetic fibers in many engineering applications. In addition to well-known conventional lignocellulosic fibers, others with promising properties are now being considered. The present work investigated the mechanical and structural characteristics of a relatively high strength fiber, curaua (Ananas erectifolius) from the Amazon region of Brazil. The results obtained from tensile tests confirmed the superior strength while scanning electron microscopy (SEM) analysis displayed features that justify the possibility of using the curaua fiber as an effective reinforcement for polymeric composites.

Jan 1, 2006

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Manuela Castaneda, Henry A. Colorado

This paper is about the use and stabilization of iron oxide based powders with arsenic contents coming from the purification of water. Cement paste samples with 0.0, 2.5, 10 and 20wt% of waste were fabricated by mixing mechanically all components. There are two main positive impacts of using this waste, first, this waste is produced in large amounts worldwide, and therefore the stabilization has a significant impact for the environment. Second, the waste can be used as an admixture and filler for cement, and therefore reduce the amount of cement in the concrete, which has a major impact in the CO2 footprint since cement industry produces a lot of this gas. Compressive strength and density tests were tested after 28 days. Microstructure was analyzed with scanning electron microscopy and x-ray diffraction. Results show that compressive strengths greater than 20 MPa were obtained and the samples had calcite, portlandite and ettringite phases.

Mar 1, 2018

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By Ismail Adeniyi Okewale, Hendrik Grobler

Significant factors believed to be responsible for tailings dam failure which can lead to loss of lives, destruction of properties and assets or damage to the environment are the mechanics of material characteristics and static liquefaction. It is therefore essential to understand the tendency for the likely occurrence of liquefaction in tailings dam as well as mechanics behind the behaviour of this tailing materials (inevitable products of ore mining, mineral and metallurgical processes). This study aims to present the mechanical behaviour and susceptibility to liquefaction of a gold tailings sample. Series of oedometer tests were conducted to determine the compression behaviour and the possibility of transitional behaviour or not. Index and physical tests were conducted to determine engineering grading descriptors which was directly linked to compression behaviour and comparisons made with other tailings. Microstructure was studied to understand the effects of fabric on the behaviour of samples and the chemical composition and mineralogy were also investigated. The compression paths slowly converge and the gold tailings might be said to be less transitional. The gold tailing is less dependent on initial state. The loosest gold tailing is more susceptible to liquefaction and compared to other gold tailings, this sample is less susceptible to liquefaction.

Apr 19, 2024

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

By Z. Hou

ABSTRACT: Short-term strength, damage and healing boundaries for rock salt are experimentally determined and integrated into the Hou/Lux-MDS damage-healing model. This model can be used to describe the mechanical behaviour of rock salt during a damaging process (under high stress to strength ratios) as well as during a healing process (under very low stress to strength ratios with high confining pressure). The development of the damage and the stress to strength ratio in the excavation damaged zone (EDZ) of a storage cavern under a minimum internal pressure as well as the development of the healing of damage and the stress to strength ratio under a subsequent maximum internal pressure are investigated project-related. The results of the investigation make it possible to shift the permissible minimum pressure boundary down, allowing the optimisation of decisive economic characteristics of storage caverns. RÉSUMÉ: Le comportement court terme, l’endommagement et les conditions de colmatage pour le sel gemme ont été étudiés expérimentalement et intégrés dans le model endommagement-colmatage Hou/Lux-MDS. Ce modèle permet de décrire le comportement mécanique de sel gemme pendant le processus d’endommagement (sous fort rapport contrainte-résistance) et le comportement du processus de colmatage sous très faible rapport contrainte-résistance avec forte pression de confinement. Le développement d’endommagement et le rapport de contrainte-résistance dans une zone d’endommagée (EDZ) d’une cavité de stockage avec un maximum de pression de soutènement ont été étudiés. Les résultats de cette étude permettent de conclure qu’il est possible de baisser la pression de soutènement, et par conséquent d’optimiser les caractéristiques économiques décisives des cavité de stockage. ZUSAMENFASSUNG: Für Steinsalz werden Festigkeits-, Schädigungs- und Verheilungsgrenze experimentell ermittelt und in das Schädigungs-Verheilungs-Modell Hou/Lux-MDS integriert. Damit kann das mechanische Verhalten von Steinsalz sowohl bei einem Schädigungsprozess (mit hohen Ausnutzungsgraden) wie auch bei einem Verheilungsprozess (mit niedrigen Ausnutzungsgraden) beschrieben werden. Projektbezogen werden die Schädigungs- und Ausnutzungsgradentwicklung in der Auflockerungszone einer Speicherkaverne unter einem minimalen Innendruck sowie die Verheilungs- und Ausnutzungsgradentwicklung unter einem anschließenden maximalen Innendruck untersucht. Die Untersuchungsergebnisse erlauben, die zulässige Minimaldruckgrenze nach unten zu verschieben, so dass entscheidende wirtschaftliche Kenngrößen von Speicherkavernen optimiert werden können.

Jan 1, 2003