Search Documents

By Littlewood E

We offer these notes as a practical contribution. All the arguments we advance have been tested by practical experience.In its preparation we realised that our subject was one of such importance and covered so wide a field that, dealt with by one of us alone, it might easily have been too much for him, so we have endeavoured, by mutual criticism and advice and a pooling of ideas, to bring forward a few points that may be of advantage to members. If any of the paper is of benefit to mining on the "Golden Mile," or elsewhere, we shall feel amply repaid for our efforts.It is obvious to all that the longer the machine is working productively per shift the greater the return, to all concerned; the machine-man himself and the company. Furthermore, if a man commences a shift with a definite objective in view; for instance, to bore and fire a specific cut, which he recognizes will give him a good financial return, then that man will exercise all his capabilities to attain that objective.In this paper we hope to demonstrate the value to the machine-man of the knowledge of the capabilities of each hole he bores, so that he will be enabled to utilize his drilling time to the greatest advantage. Also, we hope to show that such drilling time can be advantageously extended.After the war, with the influx of new men to the industry, some education on the finer points of machine work may be desirable, and any instruction in this branch must stress the realization of the value of each hole.We realise that most of those present have a sound workable knowledge of machine-mining, and we are not trying to teach anyone the fundamentals of machine work, but we would like to bring to their attentIon some of the finer points which we believe are very important.The machine-man has control of gear of a capital value of over £150, and the use or misuse of that material has a direct bearing on working costs. Therefore it is imperative that the capital outlay is gainfully employed.A "bogger" in charge of a 5/- shovel engaged unproductively is bad enough. How much worse for £150 worth of gear to be not fully productive.Figs. 1 and 2 demonstrate angles of break, and the full realization of the importance of this angle is essential to our paper. Although these Sketches are two-dimensional, we hope they will be sufficient to demonstrate our meaning. We will pass over them as briefly as possible.Fig. 1 shows three holes asked to perform an identical task.(a) 7-ft. hole bored 2 ft. into solid ground-will not come out.(b) 4-ft. hole bored 1 ft. from solid ground-will come out easily.(c) 5-ft. hole bored to solid ground-the best that can be expected under general conditions encountered.The angle of break is a right-angle, normal to direction of hole.

Jan 1, 1944

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the 'T' bracing principle. Previously, Jarva's line of tunnel boring machines, even their smallest, was designed on the 'X' or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the 'T' scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

By J. Peck, F. Brackebusch, M. Scobie

"A number of alternative strategies exist to improve narrow orebody stope productivity and safety through mechanization. Particular attention is given to one of these: the development of an in-stope mining machine. This paper summarizes those characteristics of vein orebodies in Canadian mines which are considered to govern such mining machine design. It then reviews past and current attempts to develop hardrock mining machines which could potentially be applicable to narrow stope widths.IntroductionSerious interest is mounting to exploit new technology in the development of methods and machinery to stope narrow, hardrock, orebodies. The motives relate not only to the foreseen need to maintain or reduce production costs, but also to considerations of manpower availability, safety, ground control, ore recovery and dilution. This also follows the demonstrated success of technology application in larger metal orebody stoping, where machine development has been seen to lead to improved productivity as well as the future prospects of continuous mining systems and eventual automation, e.g. ITH blasthole drill development and bulk mining. This paper deals in particular with machine design for ore fragmentation in narrow, hardrock orebodies. It is considered that such machine design closely interacts with the over-all stoping method design and that both require consideration in parallel to ensure success in mechanization."

Jan 1, 1990

By George Jones

MACHINE mining on the pitch plays an important part in the produc-tion schedule at the Salem Hill Colliery of the Haddock Mining Co. This mine is just outside the city of Pottsville, in Schuylkill County, along the southern border of the Anthracite Region. The entrance to the mine is through a cross-measure tunnel 15 ft. above water level and running north 1500 ft. until it strikes the Rabbit Hole vein, where the machine mining is carried on. The main slope, dipping south, was sunk 1200 ft. in the Rabbit Hole vein with levels turned off at 300-ft. intervals. The vein is from 24 to 30 in. thick on a varying pitch of 20° to 40°. The overburden has differed from 50 to 466 ft., the most recent work having the maximum overburden. Immediately over the Rabbit Hole vein is a seam of soft sand slate from 1 to 4 ft. thick which presents a problem at times because it dis-integrates rapidly when exposed to the air. It will crack up and fall without any audible warning, therefore the workmen must always be on the alert, watching for loose slabs. The main top is sandstone, vary-ing in thickness from 8 to 20 ft. The bottom rock is similar to the top, but is finer grained and subject to a more complete disintegration. The vein has a 3 to 4-in. shelly band along the bottom, and all under-cutting has been done in this soft band.

Jan 1, 1935

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

By C. Hendricks

This paper is based upon field studies conducted in a western Canadian open pit coal mine. This work has involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board blasthole drills and mining shovels. A review of instrumentation and monitoring methodology will first be presented. Based upon experience from field-based studies, the paper will subsequently focus on the application of monitoring technology within the framework of an integrated Equipment Monitoring System. Such a system will permit the real-time performance evaluation of key equipment involved in surface mille production.

Jan 1, 1991

By J. Sajkiewicz

In a synthetic way discussed are certain results of papers realized at the Wroclaw Technical University in a field of the theory of exploitation of machine systems with conveyor-belt transport. The attention is paid to the two lines in these works which are concerned with the development of analytical as well as simulation methods, in both cases realized with the help of digilat computers.

Jan 1, 1977

By Henry H. Thomas

In Tasmania a tailrace tunnel to handle water discharged from a turbine generator has been successfully driven by a machine tunneling method similar to that described in the July 1962 issue of Civil Engineering. The Hydro-Electric Commission, Tasmania, is constructing a high- head (2750 ft) power project that will utilize the storage in the Great Lake (1,150,000 acre-ft) at an elevation of 3380 ft. The underground power station will house six vertical shaft turbo-generators, each rated at 50,000 kw. The tailrace tunnel, 16 ft diam and 14,600 ft long, was driven through a reasonably homogeneous hard mudstone. It was decided to excavate this mechanically in the hope of saving some money on excavation and a considerable sum on the ultimate lining of the tunnel. Mechanical engineers from Tasmania worked with the firm of James S. Robbins and Associates of Seattle, Wash., which designed and supplied the "mole."

Jan 4, 1963

By I. Ocak

Initial investment for mechanical boring of tunnels is found to be high in most cases. Conventional drilling and blasting is not the possible especially in urban area. In these conditions impact hammer offers many advantages over conventional drill and blast techniques and boring tunnels. These include improved safety, minimal ground disturbances, elimination of blast vibration, reduced ventilation requirements, reduced cost etc. Therefore, hydraulic impact hammers have been used widely in metro tunnelling projects in Istanbul since 1992. Accumulated and published data from various tunnelling projects serve to improve predicting the machine performance and scheduling of job duration. This paper is prepared under this objective. Machine utilization time of impact hammer was evaluated in this study. The main rock formation named Kartal formation arepaleozoic aged sedimentary rocks, shale, sandstone, siltstone, andesite dykes and sediment fillings. The first stage of the project is commissioned to Yapi Merkezi- Yuksel- Dogus- Yenigun- Belen consortium.

Jan 1, 2011

By G. R. Forbes

Flotation froth machine vision systems provide consistent real-time measurements pertaining to the state of the flotation cell being monitored. Typical measurements include froth velocity, froth colour, froth texture and froth stability. This paper presents the results from test work conducted on the molybdenite rougher circuit at the Kennecott Utah Copper Concentrator during February 2006. Machine vision results show that it is not possible to accurately determine bubble size distribution information for the molybdenite froth, despite using state-of-the-art methods. Instead, it is necessary to make use of texture measurements to classify the various different froth states. Numerous combinations of texture measurements and classifiers are used to determine the best combination. Results show that the Fourier ring based texture measurements perform the best when both K nearest neighbour and Gaussian mixture model classifiers are used. The concentrate grade of the flotation cell is modelled using combinations of froth velocity and froth texture descriptors. The results show that by using a linear combination of these descriptors rather than either one by itself it is possible to account for a much larger percentage of the variation observed in the concentrate grade data. Adjusted R2 values of 92% and 84% are achieved when modelling the copper and the molybdenite concentrate grade respectively.

Jan 1, 2014

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967

By A. Adhikari, P. Tukkaraja, S. Jayaraman Sridharan

Shafts are critical components of the mine ventilation systems and contribute significantly to the mine ventilation pressure. Estimation of shaft pressure losses is an important aspect of mine ventilation planning and shaft frictional pressure losses are extensively studies. Shock losses contributed by shaft buntons are estimated using the interference factor model developed half a century ago. This study aims to develop a better performing prediction model for shaft buntons using state of the art experiment and numerical data, and machine learning techniques. Results show that the present prediction model is performing poorly, and the prediction performance can be improved by incorporating additional predictor variables. The Artificial Neural Network standardized Machine Learning model developed in this study is able to predict the shaft bunton shock loss with high accuracy (R2 = 0.956).

Jun 25, 2023

By S. J. Page

Introduction Dust from cutter machines and face drills is controlled in most mines by water. However, the large quantities of water used in metal and coal mines for dust control and suppression pose serious operational problems in water soluble ores, such as salt, trona, or gypsum. This paper reviews the strategies to suppress and collect dust on cutter machines and face drills where water usage must be restricted to very low flow rates - typically 3.78 L/min (1 gpm) or less.

Jan 1, 1985

Control dust generated during mining in salt mines. Approach A machine-mounted exhaust ventilation system which moves with the cutting machine from place to place was developed. The system captures the dust at the face of the heading and exhausts it downstream of the heading in the crosscut. This helps cause fresh air from the crosscut to flow over the machine operator's position, and aids in keeping the dust cloud close to the face. How It Works The system consists of (1) a circular intake hood with a 10-inch slot extending 250 degrees around the base, bolted to the gearhead; (2) 20-inch-diameter wire-wound flexible ducting to connect the intake hood to the fan (25 ft. is allowed sufficient slack for bar movement); (3) an industrial exhaust fan capable of generating 10,000 cfm with 13 inches water gage pressure at 1435 rpm; and (4) 150 ft. of collapsible 24-inch tubing for the exhaust duct which is de-played and returned In each heading by the cutter operator and/or his helper.

Jan 1, 1983

By G. Kris Kapoor

Each new period of public concern, whether rooted in things political, social, economical, or technological, brings with it new words or phrases which highlight that new interest. With people's awareness of our rapid depletion of readily available energy sources and the enormous increase in energy .costs came the new, and now often heard, terms "energy intensive", "energy sensitive", and "energy conservation". Since its birth in 1926, Fuller Company had been directly associated and involved with energy intensive products and processes. We are located in the heart of the Cement Industry. Many of our products and processes are geared to the needs of the portland cement manufacturer, and a look at the inferno within an operating cement or lime kiln will certainly convince anyone that here is an energy intensive process. Fuller Company, then, has always been energy sensitive. Process kilns, hard rock crushers, tube and roller mills, fluid bed thermal reactors, pneumatic compressors and conveyors, material coolers - all are Fuller Company products utilizing or transferring large amounts of energy. Consequently, much of our success in the marketplace depends on how wisely we design and plan for efficient use of power and for conservation of each unit of heat available.

Jan 1, 1975

By A. Smithson

It is generally accepted by British mining engineers that coal will continue to be worked by the. advancing or retreating longwall system for the foreseeable future. At the coal face, the emphasis will be on better machine utilization; increased equipment reliability; modular design and more standardization; remote control and monitoring; and a continuing drive to increase productivity and safety. Improvements at the face can be sustained only if there are corresponding improvements in efficiency elsewhere in the mine. Coal handling systems, for example, must be able to accept increased tonnages without creating bottlenecks. As workings move further from the shafts, the time taken to transport men and materials must be kept within reasonable limits. Development drivages must he on schedule to be ready for the planned opening of new faces, and face ends must keep up with faster moving faces.

Jan 8, 1981

By Dan Nower

Machinery Health Monitoring of Shovels MINExpo 2012: Caterpillar announced the largest Electric Rope Shovel, capable of 120 short tons The next day, JoyGlobal (P&H Mining) ?one-upped? CAT, introduced a shovel capable of 135 short tons Large Concern: breakdown (unplanned outages) of one machine will be more disruptive to production

May 1, 2013

By William G. Kegel

Aside from having a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in acquiring this is the presence of good mechanics-men who have a desire to be mechanics and who want to know more about the design and control of the machines in their charge. The knowledge and ability to be found in a good mechanic is the result of ambition, curiosity, and determination. With these qualities as a start, the aspiring mechanic can launch his career if he begins learning all he can about mechanics, electricity, and hydraulics. The path is rough, but the goal is rewarding. Mining machinery probably absorbs as much or more abuse than any other heavy equipment in use today. And when one considers the conditions under which much of the repair work must be done, it can be seen that the mine operator needs the best of men and tools to perform the service. MOTORS AND POWER SUPPLY Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were large, heavy-framed, open d-c motors (direct current), using a series or shunt winding. A motor having one or more field coils connected in series and themselves in series with the armature, is called a series motor (Fig. 1). The series motor had the advantage of quickly developing starting torque, and it was, and still is, the best motor for locomotive or shuttle car tramming service. The series motor, however, speeds up as the load is reduced and, if not properly controlled, can overspeed. The shunt motor, as its name implies, has one or more field coils in

Jan 1, 1973

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By William G. Kegel

Apart from a usable product and good 'mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and- an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating shaft. In the case of a locomotive, this principle is used in dynamic braking. The momentum of the locomotive drives the motor and generates d-c power. The power is regulated with resistors and provides opposition to the motion of the locomotive.

Jan 1, 1981