Search Documents

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By K. H. Lee

The rate of beryllium dissolution from a low-grade ore was studied in sulfuric acid solutions. The effect of stirring speed, sulfuric acid concentration, particle size and temperature on the rate of dissolution of beryllium was established. The results of the study showed that the dissolution rate is independent of stirring speed within the range of 250-1000 rpm but depends on 1/2 power of the sulfuric acid concentration. The dissolution rate increases exponentially with decrease in particle size and the maximum attainable rate of extraction with respect to particle size is 6.6 x 10 mol dm min. The apparent activation energy (^E) for the dissolution reaction is 54.4 kJ/mol (13.0 kcal/mol). Based on this magnitude of the activation energy, it is concluded that a surface chemical reaction is the rate limiting step for the temperature range (70° -100°C) investigated.

Jan 1, 1988

By Paul L. Wichlacz

A mathematical model of growth and ferrous iron oxidation for attached bacteria was applied to rotating biological contactor (RBC) units treating acidic mine drainage. The model describes attached bacterial growth as a saturation function, where the rate of substrate utilization is determined by a maximum substrate oxidation rate constant, a half saturation constant, and the concentration of substrate within the RBC. The maximum oxidation rate constant was proportional to flow rate and the substrate concentration in the reactor varied with influent substrate concentration. The model was tested at three separate sites and with three different size RBC units. The ability of the model to predict the rate of iron oxidation under all test conditions was significant. The accuracy of the model was found to be affected by unit size and vary with specific test site.

Jan 1, 1985

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

Kinetics of bubble-particle interaction, surface hydrophobicity and interfacial phenomena in sulfide mineral flotation are discussed in this paper. Results of the measurements of a bubble and mineral induction time (IT) and detachment force (DF), vacuum of bubble evolution (VE) and mineral floatability are discussed for pyrite, galena, chalcocite and chalcopyrite. Natural wetting and wetting induced by xanthates with different lengths of alkyl chains are examined. Experiments show the existence of several maxima of hydrophobicity on dependences of pH and electrochemical potential. These maxima are attributed as the reflection of mineral surface heterogeneity due to xanthate adsorption and the presence of cationic and anionic centres with uncompensated positive and negative charges. These charges can be neutralised by both regulation pH and applied potential. The aim of this paper is to evaluate a thickness of the rupturing film and to estimate how long the bubble-mineral interactions are according to the experimental values of IT, in order to develop a procedure for comparing of the results of DF and atomic force measurements in the same dimensionality, and to compare the results of the experimental studies on the wettability of sulfides with those predicted by the models of physics of capillarity.

Jan 1, 2005

By J. L. Hendrix, R. B. Dix

A study was made of the United States Bureau of Mines chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and mechanisms involved in the reactions between galena and sphalerite with chlorine. The influence of copper on the extraction rates was also studied. It has been shown that the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373 K with rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1981

By N. Kanari

Kinetics of the carbochlorination of Cr2O3 has been studied with C12+CO gas mixtures between 500 °C to 900 °C using thermogravimetric analysis. The apparent activation energy is about 100 kJ/mol. Mathematical fitting of the experimental data suggests that the shrinking sphere model is the most adequate to describe the carbochlorination mechanism of chromium oxide and that is controlled by the chemical reaction. In the temperature range of 550 "C to 800 OC, the reaction order is about 1.34 and is independent of temperature. Changing the C12+CO content from 15 pct to 100 pct increases the reaction rate and does not affect the reaction mechanism. Similarly, changing the ratio of C12/(Cl2+CO) from 0.125 to 0.857 do not modify the carbochlorination mechanism of Cr203. In these conditions, the reaction rate passes through a maximum when using a chlorinating gas mixture having a Cl2/(C12+CO) ratio of about 0.5.

Jan 1, 1998

By Jagannath Pal, Ammasi Ayyandurai

Hematite ore pellets require a much higher induration temperature than magnetite ore pellets because no exothermic heat is generated due to oxidation inside during induration-like magnetite pellets. Carbon is used as in situ heat source in hematite ore pellets which can reduce temperature requirement in the induration strand and hence decreases energy consumption. Many investigators have reported that a 0.8–1.25% addition of carbon in hematite pellets can improve the pellet properties also. However, to investigate the exact role of carbon in hematite pellets, its reaction mechanisms and kinetics study are required which have not been done so far. Therefore, the reaction mechanism and its kinetics have been studied in this investigation. It has been found that carbon reaction happens in pellets from the surface towards the center in a topochemical manner which is controlled by pore diffusion of gas, and its activation energy is around 52 k J mol− 1. It is also found that apart from in situ heat, carbon in hematite pellets enhances diffusion bonding which improves pellet properties. This study ascertains the exact role of carbon in hematite pellets which may help operators to use carbon effectively to reduce energy consumption and improve pellet properties.

Nov 6, 2022

By I. Iwasaki, K. A. Smith, X. Cheng

A cathodic decomposition model was examined for both pyrrhotite and chalcopyrite in an attempt to analyze the formation of surface coatings in deoxygenated solutions at natural, near neutral pH. Combination potentials established between the mineral-grinding media pair were simulated by applying a potential of -0.455 V (vs. a standard hydrogen electrode) either to a pyrrhotite or to a chalcopyrite electrode. Chronoamperometry was used to study the polarization behaviors and alteration of mineral surfaces through cathodic processes. The kinetic parameters of cathodic decomposition of pyrrhotite and chalcopyrite were determined and compared. It was concluded that pyrrhotite decomposed faster than chalcopyrite in near-neutral pH solutions. Both minerals were then covered by a film consist¬ing mainly of iron hydroxides, which adversely affected their flotation.

Jan 1, 1999

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By E. A. Brocchi, D. H. Gameiro, P. K. Jena

Carbon tetrachloride was found to be a very efficient chlorinating agent for anatase concentrate, even at the low temperatures that were investigated (250-400 degrees C). For example, at 400 degrees C about 90% of the anatase concentrate was found to have been chlorinated within 60 minutes

Jun 13, 1905

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article thefollowing hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the of chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By A Holmgren, W Forsling

In the present study infrared attenuated total reflection (IR-ATR) was used to monitor the rate of in situ adsorption of heptyl xanthate on a layer of zinc sulfide synthesised on a germanium ATR crystal. The zinc sulfide surface was characterised using x-ray photoelectron spectroscopy (XPS). The absorbance of heptyl xanthate measured increased with increasing bulk concentration of the adsorbate up to an equilibrium plateau value corresponding to a fractional coverage of the surface sites of the substrate. For the adsorption from solutions of concentrations between 10-3 and 10-5 M, the rate of adsorption increased with increasing bulk concentration. At higher concentrations the measured absorbance should be corrected for the absorbance due to the concentration of xanthate in bulk solution. The present work provides a discussion of this correction. Assuming the adsorption stage to be rate-controlling and proportional both to the concentration of the adsorbing species in solution and unreacted surface area, a rate law governing this type of transient adsorption kinetics was derived. By means of absorbance data for the concentrations 0.1 and 0.01 mM, the rate constant of adsorption was calculated. From the initial part of a Langmuir adsorption isotherm, the absorbance at monolayer coverage and the equilibrium constant of adsorption could be estimated.

Jan 1, 2005

By M. J. Adam

The U.S. Bureau of Mines is investigating the partitioning of selected complex minerals into simple phases using sulfidation reactions. Successful partitioning of complex mineralogy to simple phases may afford an opportunity to improve selective extraction of mineral constituents of economic value. The research has shown that complex minerals, such as chalcopyrite (CuFeS2) and pentlandite [(Fe,Ni)9Se]' may be partitioned to the simpler phases covellite (CuS) plus pyrite (FeS2) and vaesite (NiS2) plus pyrite (FeS2), respectively. Demonstrations of these reactions were verified through long-react ion-time (24 h or more) experiments, but basic rate investigations and modeling were not included in the previous research. This report describes research aimed at determining the rate at which the complex mineral CuFeS2 converts to the simple sulfides CuS plus FeS2. Small samples of CuFeS2 were blended with elemental S prior to thermal treating under an He atmosphere for time periods up to 4 h. Products from each treatment period were characterized using metallography, chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Results of the investigation revealed a rapid conversion of CuFeS2 to CuS plus FeS2 early in thermal treatment periods. As the reaction occurred, a CuS rimming of particles was observed which separated the reacting species (CuFeS2 and S) and caused a considerable decrease in transformation rate.

Jan 1, 1991

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By A. Warczok

The mechanisms and kinetics of copper oxidation and reduction have been investigated in small scale thermal gravimetric experiments as well as in laboratory pilot scale, packed bed reactors. With blister copper flowing gravitationally down through a packed bed of ceramic particles, counter-current to low oxygen containing combustion gases, the rate of oxidation was found to be very high due to the large surface area created. Similarly, reduction by flowing copper through a packed bed of charcoal lead to rapid de-oxidation. Based on these laboratory measurements, fundamental rate data have been obtained. Modeling of industrial sized packed bed reactors using the laboratory results, opened up the possibilities of developing a new, very intensive, continuous process for copper fire refining. The developed mathematical model together with a computer process simulator, allowed for the design of the industrial-pilot installation to be built and tested at the ENAMI Paipote smelter in Chile.

Jan 1, 2007

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.